Clock OSC
SG5032VAN
SG5032VAN 75.000000 MHz KJBA
Product name
X1G0042610049xx
Product Number / Ordering code
Please refer to the 9.Packing information about xx (last 2 digits)
Output waveform
LVDS
Pb free / Complies with EU RoHS directive
Reference weight Typ. 52 mg
1.Absolute maximum ratings
Parameter
Symbol
Maximum supply voltage
Storage temperature
Input voltage
Min.
-0.3
-40
-0.3
Typ.
-
-
-
Max.
+4
+125
Vcc+0.3
Unit
V
ºC
V
Conditions / Remarks
-
Storage as single product
ST or OE Terminal
Vcc-GND
T_stg
Vin
2.Specifications(characteristics)
Parameter
Symbol
Output frequency
Supply voltage
Operating temperature
Frequency tolerance
Current consumption
Stand-by current
Disable current
Symmetry
Output voltage(LVDS)
Min.
-
2.25
-20
-50
-
-
-
45
250
-
1.15
-
-
0.7Vcc
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-5
-
Typ.
75.0000
-
-
-
-
-
-
-
-
-
-
-
100
-
-
-
-
-
9.4
2.3
5.4
28.9
-
TBD
-
TBD
TBD
TBD
TBD
TBD
TBD
-
-
Max.
-
3.63
+70
50
30
0.0
20.0
55
450
50
1.35
150
-
-
0.3Vcc
300
300
3
-
-
-
-
-
-
-
-
-
-
-
-
-
5
-
Unit
MHz
V
ºC
x10
-6
mA
mA
mA
%
mV
mV
V
mV
Ω
Conditions / Remarks
-
-
-
OE=Vcc L_LVDS=100 ohm
-
OE=GND
-
-
-
-
-
-
-
-
Output load condition(LVDS)
Input voltage
Rise time
Fall time
Start-up time
Jitter
Phase jitter
Phase noise
f0
Vcc
T_use
f_tol
Icc
I_std
I_dis
SYM
V
OD
dV
OD
Vos
dVos
L_LVDS
V
IH
V
IL
t
r
tf
t_str
t
DJ
T
RJ
t
RMS
t
p-p
t
acc
t
PJ
L(f)
ps
ps
ms
ps
ps
ps
ps
ps
ps
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
-6
-
-
-
Deterministic Jitter Vcc=2.5V
Random Jitter Vcc=2.5V
δ(RMS of total distribution) Vcc=2.5V
Peak to Peak Vcc=2.5V
-
Off set Frequency: 12kHz to 20MHz Vcc=2.5V
-
Off set 10Hz Vcc=2.5V
Off set 100Hz Vcc=2.5V
Off set 1kHz Vcc=2.5V
Off set 10kHz Vcc=2.5V
Off set 100kHz Vcc=2.5V
Off set 1MHz Vcc=2.5V
Frequency aging
f_age
x10 /Year
25℃,1stYear
-
1 Page
3.Test circuit
1) To observe waveform and current (case 1)
A
+3.3 V
By-pass
capacitor 2
Power
supply 1
Vcc
OUT
OUT
Differentila probe
100 Ω
OE
OE pin*
NC
GND
Oscillo-
scope
By-pass
capacitor 1
* The lines from OUT and OUT pin are same length.
* To measure the disable current, OE pin is connected to GND
2) To observe waveform and current (case 2)
A
+3.3 V
By-pass
capacitor 2
Power
supply 1
Vcc
OUT
OUT
50 Ω
OE
OE pin
NC
GND
50 Ω
By-pass
capacitor 1
V
OD
V
V
V
OS
* The lines from OUT and OUT pin are same length.
3) Measurement condition
A) Oscilloscope
•Bandwidth should be 5 times higher than DUT’s output frequency (4 GHz).
•Probe ground should be placed closely from test point and lead length should be as short as possible.
B) By-pass capacitor 1 (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
C) By-pass capacitor 2 (approx. 10 μF) places closely between power supply terminals on the board.
D) Use the current meter whose internal impedance value is small.
E) Power supply
• Start up time (0 Vg90 %Vcc) of power source should be more than 150 μs and
slew rate should be less than 19.8 mV/μs.
• Impedance of power supply should be as low as possible.
2 Page
4.Timing chart
Each output waveform (OUT, and OUT)
Vcc
OUT
50 % of OUT
amplitude
50 % of OUT
amplitude
OUT
V
OS1
GND
V
OS2
tw
SYM = tw / t
t
Differential output waveform (OUT
–
OUT)
dV
OS
=½V
OS1
-V
OS2
½
tr
tf
80 % of amplitude
Differential
0V
OUT
V
OD1
V
OD2
OUT
20 % of amplitude
dV
OD
=½V
OD1
-V
OD2
½
5.External dimensions
(Unit: mm)
6.Footprint(Recommended)
0.89
#6
(Unit: mm)
1.60
2.60
0.89
#4
#5
#1
#2
#3
2.54
To maintain stable operation, provide a 0.01uF to 0.1uF
by-pass capacitor at a location as near as possible to the
power source terminal of the crystal product (between Vcc
- GND).
3 Page
7.Reflow profile
Reflow condition (Follow of JEDEC STD-020D.01)
300
250
200
150
100
50
Time
+25CtoPeak
0
60
120 180 240 300 360 420 480 540 600 660 720 780
Time[s]
;+217C
Tsmax;+200C
TL
Temperature[C]
TP
;+260C
+255C
Avg.
Ramp-up
3
C/sMax.
tp
;20sto40s
tL
60sto150s
(+217Cover)
Ramp-down
6C/sMax.
Tsmin;+150C
ts
60sto180s
(+150Cto+200C)
8.Example of schematic layout
This figure shows an example of this product’s application schematic.
As with any high speed analog circuitry, the power supply pins for this device are vulnerable to
noise. In order to achieve optimum jitter performance, power isolation with filter device is
required for power supply pins.
In order to achieve best performance of the power isolation filter, it is recommended that the filter
composing devices is placed on the device side of the PCB as close to the power pins as
possible. The component value of this filter is just an example, it may have to be adjusted.
4 Page
* By-pass capacitor (approx. 0.01 μF to 0.1 μF) places closely between Vcc and GND.
* By-pass capacitor (approx. 10 μF) places closely between power supply terminals on the board.
* Please design the two output lines by characteristic impedance 100 Ω and same length, and try
to make the output lines as short as possible.
9.Packing information
[ 1 ]Product number last 2 digits code(xx) description
The recommended code is "00"
Code
13
00
Condition
500pcs / Reel
1000pcs / Reel
X1G0042610049xx
Code
01
11
12
Condition
Any Q'ty vinyl bag(Tape cut)
Any Q'ty / Reel
250pcs / Reel
5 Page
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
