lithic power divider in a low cost SOIC-16 plastic
package. The 6-way power divider is ideally suited
for applications where PCB real estate is at a pre-
mium and part count reduction and cost are critical.
Typical applications include base station switching
networks and other cellular equipment, including
subscriber units. Available in Tape and Reel.
The MAPDCC0019 is fabricated using a passive-
integrated circuit process. The process features full-
chip passivation for increased performance and reli-
ability.
1.
All unused pins must be RF and DC grounded.
Pin Configuration
Pin No.
Function
GND
RF 3 (OUT)
GND
RF 2 (OUT)
GND
RF 1 (OUT)
GND
RF IN
Pin No.
9
10
11
12
13
14
15
16
Function
GND
GND
RF 6 (OUT)
GND
RF 5 (OUT)
GND
RF 4 (OUT)
GND
Ordering Information
Part Number
MAPDCC0019
MAPDCC0019-TR
MAPDCC0019-TB
1
2
Package
Bulk Packaging
1000 piece reel
Sample Test Board
3
4
5
6
7
Note: Reference Application Note M513 for reel size
information.
8
1
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0019
Low Cost Six-Way Power Divider
824 – 960 MHz
Electrical Specifications: T
A
= 25°C, Z
0
= 50
Parameter
Insertion Loss above 7.8 dB
Isolation
VSWR
Input
Output
Rev. V2
Units
dB
dB
—
—
dB
Deg.
Min
—
20
—
—
—
—
Typ
0.8
25
1.4:1
1.3:1
0.5
4
Max
1.2
—
1.8:1
1.5:1
0.9
8
Amplitude Balance
Phase Balance
Absolute Maximum Ratings
2,3
Parameter
Input Power
4
Operating Temperature
Storage Temperature
Handling Procedures
Please observe the following precautions to avoid
damage:
Absolute Maximum
1 W CW
-40°C to +85°C
-65°C to +150°C
Static Sensitivity
GMIC Circuits are sensitive to electrostatic
discharge (ESD) and can be damaged by static
electricity. Proper ESD control techniques should
be used when handling these devices.
2. Exceeding any one or combination of these limits may cause
permanent damage to this device.
3. M/A-COM does not recommend sustained operation near
these survivability limits.
4. With internal load dissipation of 0.125 W maximum.
Typical Performance Curves
Insertion Loss vs. Frequency
Amplitude Imbalance vs. Frequency
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0019
Low Cost Six-Way Power Divider
824 – 960 MHz
Rev. V2
Typical Performance Curves
Isolation vs. Frequency
Phase Imbalance vs. Frequency
Input VSWR vs. Frequency
Output VSWR vs. Frequency
3
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0019
Low Cost Six-Way Power Divider
824 – 960 MHz
Lead-Free,
SOIC-16
†
Rev. V2
†
Reference Application Note M538 for lead-free solder reflow
recommendations.
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0019
Low Cost Six-Way Power Divider
824 – 960 MHz
Rev. V2
M/A-COM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
电源技术
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
