• Wide Range 1.7 to 3.6 volt for read, erase, and program operations
• Multi I/O Support - Single I/O, Dual I/O and Quad I/O
• Program Suspend/Resume & Erase Suspend/Resume
• Low Power Mode and High Performance Mode
P/N: PM2218
1
REV. 0.00, JAN. 12, 2015
ADVANCED INFORMATION
MX25R1035F
Contents
1. FEATURES .............................................................................................................................................................. 4
2. GENERAL DESCRIPTION ..................................................................................................................................... 6
6. DATA PROTECTION.............................................................................................................................................. 10
Table 2. Protected Area Sizes ................................................................................................................... 11
Read Electronic Manufacturer ID & Device ID (REMS) ........................................................................... 23
ID Read .................................................................................................................................................... 24
Table 9. Readable Area of Memory While a Program or Erase Operation is Suspended .........................56
Table 10. Acceptable Commands During Program/Erase Suspend after tPSL/tESL ................................56
Table 11. Acceptable Commands During Suspend (tPSL/tESL not required) ...........................................57
9-31. Program Resume and Erase Resume ..................................................................................................... 58
9-32. No Operation (NOP) ................................................................................................................................ 59
9-33. Software Reset (Reset-Enable (RSTEN) and Reset (RST)) ................................................................... 59
9-34. High Voltage Operation ............................................................................................................................ 60
11. POWER-ON STATE ............................................................................................................................................. 68
16. ORDERING INFORMATION ................................................................................................................................ 82
17. PART NAME DESCRIPTION ............................................................................................................................... 83
18. PACKAGE INFORMATION .................................................................................................................................. 84
P/N: PM2218
3
REV. 0.00, JAN. 12, 2015
ADVANCED INFORMATION
MX25R1035F
Wide Vcc Range 1M-BIT [x 1/x 2/x 4] CMOS MXSMIO
®
(SERIAL MULTI I/O)
FLASH MEMORY
1. FEATURES
GENERAL
• Supports Serial Peripheral Interface -- Mode 0 and Mode 3
•
1,048,576 x 1 bit structure or 524,288 x 2 bits (two I/O mode) structure or 262,144 x 4 bits (four I/O mode)
structure
• Equal Sectors with 4K byte each, or Equal Blocks with 32K/64K byte each
- Any Block can be erased individually
• Single Power Supply Operation
- 1.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
PERFORMANCE
• High Performance
- Fast read
- 1 I/O: 80MHz with 8 dummy cycles
- 2 I/O: 80MHz with 4 dummy cycles, equivalent to 160MHz
- 4 I/O: 80MHz with 2+4 dummy cycles, equivalent to 320MHz
- Fast program and erase time
- 8/16/32/64 byte Wrap-Around Burst Read Mode
• Low Power Consumption
• Typical 100,000 erase/program cycles
• 20 years data retention
SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Advanced Security Features
- Block lock protection
The BP0-BP3 status bit defines the size of the area to be software protection against program and erase
instructions
• Additional 8K bits secured OTP
- Features unique identifier.
- Factory locked identifiable and customer lockable
• Auto Erase and Auto Program Algorithm
-
Automatically erases and verifies data at selected sector or block
-
Automatically programs and verifies data at selected page by an internal algorithm that automatically times the
program pulse widths (Any page to be programed should have page in the erased state first)
•
Status Register Feature
•
Command Reset
•
Program/Erase Suspend and Program/Erase Resume
•
Electronic Identification
-
JEDEC 1-byte manufacturer ID and 2-byte device ID
- RES command for 1-byte Device ID
- REMS command for 1-byte manufacturer ID and 1-byte device ID
•
Support Serial Flash Discoverable Parameters (SFDP) mode
P/N: PM2218
4
REV. 0.00, JAN. 12, 2015
ADVANCED INFORMATION
MX25R1035F
HARDWARE FEATURES
•
SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• SO/SIO1
- Serial Data Output or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• WP#/SIO2
- Hardware write protection or serial data Input/Output for 4 x I/O read mode
• RESET#/SIO3
- Hardware Reset pin or Serial input & Output for 4 x I/O read mode
我最近在《华尔街日报》看到一篇题为“我们需要能维修自己的电子小玩意儿的权利(We need the right to repair our gadgets)”的文章(参考原文:),作者对于众多电子产品看来是“有计画的废弃(planned obsolescence)”之现象非常愤怒,认为大众应该要求电子产品可以被维修。 但实际的情况是,举例来说,家家都有的电视机如果故障了,修理费用可能...[详细]