74LVC1G125
Bus buffer/line driver; 3-state
Rev. 9 — 29 December 2010
Product data sheet
1. General description
The 74LVC1G125 provides one non-inverting buffer/line driver with 3-state output.
The 3-state output is controlled by the output enable input (OE). A HIGH-level at pin OE
causes the output to assume a high-impedance OFF-state.
The input can be driven from either 3.3 V or 5 V devices. This feature allows the use of
this device in a mixed 3.3 V and 5 V environment.
This device is fully specified for partial power-down applications using I
OFF
. The I
OFF
circuitry disables the output, preventing the damaging backflow current through the device
when it is powered down.
2. Features and benefits
Wide supply voltage range from 1.65 V to 5.5 V
High noise immunity
Complies with JEDEC standard:
JESD8-7 (1.65 V to 1.95 V)
JESD8-5 (2.3 V to 2.7 V)
JESD8-B/JESD36 (2.7 V to 3.6 V)
24
mA output drive (V
CC
= 3.0 V)
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
CMOS low power consumption
Inputs accept voltages up to 5 V
Latch-up performance exceeds 250 mA
Direct interface with TTL levels
Multiple package options
Specified from
40 C
to +85
C
and
40 C
to +125
C
NXP Semiconductors
74LVC1G125
Bus buffer/line driver; 3-state
3. Ordering information
Table 1.
Ordering information
Package
Temperature range
74LVC1G125GW
74LVC1G125GV
74LVC1G125GM
74LVC1G125GF
74LVC1G125GN
74LVC1G125GS
40 C
to +125
C
40 C
to +125
C
40 C
to +125
C
40 C
to +125
C
40 C
to +125
C
40 C
to +125
C
Name
TSSOP5
SC-74A
XSON6
XSON6
XSON6
XSON6
Description
plastic thin shrink small outline package; 5 leads;
body width 1.25 mm
plastic surface-mounted package; 5 leads
plastic extremely thin small outline package;
no leads; 6 terminals; body 1
1.45
0.5 mm
plastic extremely thin small outline package;
no leads; 6 terminals; body 1
1
0.5 mm
extremely thin small outline package; no leads;
6 terminals; body 0.9
1.0
0.35 mm
extremely thin small outline package; no leads;
6 terminals; body 1.0
1.0
0.35 mm
Version
SOT353-1
SOT753
SOT886
SOT891
SOT1115
SOT1202
Type number
4. Marking
Table 2.
Marking
Marking code
[1]
VM
V25
VM
VM
VM
VM
Type number
74LVC1G125GW
74LVC1G125GV
74LVC1G125GM
74LVC1G125GF
74LVC1G125GN
74LVC1G125GS
[1]
The pin 1 indicator is located on the lower left corner of the device, below the marking code.
5. Functional diagram
2
A
Y
4
2
4
A
Y
1
OE
mna118
1
EN
mna119
OE
mna120
Fig 1.
Logic symbol
Fig 2.
IEC logic symbol
Fig 3.
Logic diagram
74LVC1G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 9 — 29 December 2010
2 of 19
NXP Semiconductors
74LVC1G125
Bus buffer/line driver; 3-state
6. Pinning information
6.1 Pinning
74LVC1G125
74LVC1G125
OE
A
1
2
GND
GND
3
001aaf198
OE
5
V
CC
1
6
V
CC
OE
A
74LVC1G125
1
2
3
6
5
4
V
CC
n.c.
Y
A
2
5
n.c.
3
4
Y
GND
4
Y
001aaf199
001aaf400
Transparent top view
Transparent top view
Fig 4.
Pin configuration
SOT353-1 and SOT753
Fig 5.
Pin configuration SOT886
Fig 6.
Pin configuration SOT891,
SOT1115 and SOT1202
6.2 Pin description
Table 3.
Symbol
OE
A
GND
Y
n.c.
V
CC
Pin description
Pin
SOT353-1, SOT753
1
2
3
4
-
5
SOT886, SOT891, SOT1115, SOT1202
1
2
3
4
5
6
output enable input
data input
ground (0 V)
data output
not connected
supply voltage
Description
7. Functional description
Table 4.
Input
OE
L
L
H
[1]
H = HIGH voltage level;
L = LOW voltage level;
X = don’t care;
Z = high-impedance OFF-state.
Function table
[1]
Output
A
L
H
X
Y
L
H
Z
74LVC1G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 9 — 29 December 2010
3 of 19
NXP Semiconductors
74LVC1G125
Bus buffer/line driver; 3-state
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
V
CC
I
IK
V
I
I
OK
V
O
I
O
I
CC
I
GND
P
tot
T
stg
[1]
[2]
[3]
Parameter
supply voltage
input clamping current
input voltage
output clamping current
output voltage
output current
supply current
ground current
total power dissipation
storage temperature
Conditions
V
I
< 0 V
[1]
Min
0.5
50
0.5
-
[1][2]
[1][2]
Max
+6.5
-
+6.5
50
V
CC
+ 0.5
+6.5
50
100
-
250
+150
Unit
V
mA
V
mA
V
V
mA
mA
mA
mW
C
V
O
> V
CC
or V
O
< 0 V
Active mode
Power-down mode
V
O
= 0 V to V
CC
0.5
0.5
-
-
100
T
amb
=
40 C
to +125
C
[3]
-
65
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
When V
CC
= 0 V (Power-down mode), the output voltage can be 5.5 V in normal operation.
For TSSOP5 and SC-74A packages: above 87.5
C
the value of P
tot
derates linearly with 4.0 mW/K.
For XSON6 package: above 118
C
the value of P
tot
derates linearly with 7.8 mW/K.
9. Recommended operating conditions
Table 6.
Symbol
V
CC
V
I
V
O
T
amb
t/V
Recommended operating conditions
Parameter
supply voltage
input voltage
output voltage
ambient temperature
input transition rise and fall rate
V
CC
= 1.65 V to 2.7 V
V
CC
= 2.7 V to 5.5 V
Active mode
V
CC
= 0 V; Power-down mode
Conditions
Min
1.65
0
0
0
40
-
-
Typ
-
-
-
-
-
-
-
Max
5.5
5.5
V
CC
5.5
+125
20
10
Unit
V
V
V
V
C
ns/V
ns/V
74LVC1G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 9 — 29 December 2010
4 of 19
NXP Semiconductors
74LVC1G125
Bus buffer/line driver; 3-state
10. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
T
amb
=
40 C
to +85
C
V
IH
HIGH-level input voltage
V
CC
= 1.65 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 2.7 V to 3.6 V
V
CC
= 4.5 V to 5.5 V
V
IL
LOW-level input voltage
V
CC
= 1.65 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 2.7 V to 3.6 V
V
CC
= 4.5 V to 5.5 V
V
OL
LOW-level output voltage
V
I
= V
IH
or V
IL
V
CC
= 1.65 V to 5.5 V; I
O
= 100
A
V
CC
= 1.65 V; I
O
= 4 mA
V
CC
= 2.3 V; I
O
= 8 mA
V
CC
= 2.7 V; I
O
= 12 mA
V
CC
= 3.0 V; I
O
= 24 mA
V
CC
= 4.5 V; I
O
= 32 mA
V
OH
HIGH-level output voltage V
I
= V
IH
or V
IL
V
CC
= 1.65 V to 5.5 V; I
O
=
100 A
V
CC
= 1.65 V; I
O
=
4
mA
V
CC
= 2.3 V; I
O
=
8
mA
V
CC
= 2.7 V; I
O
=
12
mA
V
CC
= 3.0 V; I
O
=
24
mA
V
CC
= 4.5 V; I
O
=
32
mA
I
I
I
OZ
I
OFF
I
CC
I
CC
C
I
input leakage current
OFF-state output current
V
CC
= 0 V to 5.5 V; V
I
= 5.5 V or GND
V
CC
= 3.6 V; V
I
= V
IH
or V
IL
;
V
O
= 5.5 V or GND
V
I
= 5.5 V or GND;
V
CC
= 1.65 V to 5.5 V; I
O
= 0 A
per pin; V
CC
= 2.3 V to 5.5 V;
V
I
= V
CC
0.6 V; I
O
= 0 A
V
CC
0.1
1.2
1.9
2.2
2.3
3.8
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.1
0.1
0.1
5
5
-
-
-
-
-
-
5
10
10
10
500
-
V
V
V
V
V
V
A
A
A
A
A
pF
-
-
-
-
-
-
-
-
-
-
-
-
0.1
0.45
0.3
0.4
0.55
0.55
V
V
V
V
V
V
0.65
V
CC
-
1.7
2.0
0.7
V
CC
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.7
0.8
0.3
V
CC
V
V
V
V
V
V
V
Conditions
Min
Typ
[1]
Max
Unit
0.35
V
CC
V
power-off leakage current V
CC
= 0 V; V
I
or V
O
= 5.5 V
supply current
additional supply current
input capacitance
74LVC1G125
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 9 — 29 December 2010
5 of 19
Microchip MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
