MIC5310
Dual 150mA µCap LDO in 2mm x 2mm MLF
®
General Description
The MIC5310 is a tiny Dual Ultra Low Dropout
(ULDO™) linear regulator ideally suited for portable
electronics due to its high power supply ripple
rejection (PSRR) and ultra low output noise. The
MIC5310 integrates two high-performance 150mA
ULDOs into a tiny 2mm x 2mm leadless MLF
®
package, which provides exceptional thermal package
characteristics.
The MIC5310 is a µCap design which enables
operation with very small ceramic output capacitors
for stability, thereby reducing required board space
and component cost. The combination of extremely
low-drop-out voltage, high power supply rejection and
exceptional thermal package characteristics makes it
ideal for powering RF/noise sensitive circuitry, cellular
phone camera modules, imaging sensors for digital
still cameras, PDAs, MP3 players and WebCam
applications
The MIC5310 ULDO™ is available in fixed-output
®
voltages in the tiny 8-pin 2mm x 2mm leadless MLF
package which occupies less than half the board area
of a single SOT-6 package. Additional voltage options
are available. For more information, contact Micrel
marketing department.
Data sheets and support documentation are found on
the Micrel web site
www.micrel.com.
Features
•
•
•
•
•
•
•
•
•
•
•
•
2.3V to 5.5V input voltage range
Ultra-low dropout voltage ULDO™ 35mV @ 150mA
High PSRR - >70dB @ 1KHz
Ultra-low output noise: 30µV
RMS
±2% initial output accuracy
Tiny 8-pin 2mm x 2mm MLF
®
leadless package
Excellent Load/Line transient response
Fast start up time: 30µs
µCap stable with 1µF ceramic capacitor
Thermal shutdown protection
Low quiescent current: 75µA per output
Current limit protection
Applications
•
•
•
•
•
•
Mobile phones
PDAs
GPS receivers
Portable electronics
Portable media players
Digital still and video cameras
Typical Application
ULDO is a trademark of Micrel, Inc.
MLF and
MicroLeadFrame
are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 •
http://www.micrel.com
March 2011
M9999-032411-C
Micrel, Inc.
MIC5310
Absolute Maximum Ratings
(1)
Supply Voltage (V
IN
) .....................................0V to +6V
Enable Input Voltage (V
EN
)...........................0V to +6V
Power Dissipation...........................Internally Limited
(3)
Lead Temperature (soldering, 3sec ...................260°C
Storage Temperature (T
S
) ................. -65°C to +150°C
ESD Rating
(4)
.........................................................2kV
Operating Ratings
(2)
Supply voltage (V
IN
)............................... +2.3V to +5.5V
Enable Input Voltage (V
EN
).............................. 0V to V
IN
Junction Temperature ......................... -40°C to +125°C
Junction Thermal Resistance
MLF-8 (θ
JA
) ............................................... 90°C/W
Electrical Characteristics
(5)
V
IN
= EN1 = EN2 = V
OUT
+ 1.0V; higher of the two regulator outputs, I
OUTLDO1
= I
OUTLDO2
= 100µA; C
OUT1
= C
OUT2
= 1µF;
C
BYP
= 0.1µF; T
J
= 25°C,
bold
values indicate –40°C
≤
T
J
≤
+125°C, unless noted.
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation
Dropout Voltage (Note
6)
Conditions
Variation from nominal V
OUT
Variation from nominal V
OUT
; –40°C to +125°C
V
IN
= V
OUT
+ 1V to 5.5V; I
OUT
= 100µA
I
OUT
= 100µA to 150mA
I
OUT
= 100µA
I
OUT
= 50mA
I
OUT
= 100mA
I
OUT
= 150mA
Ground Current
EN1 = High; EN2 = Low; I
OUT
= 100µA to 150mA
EN1 = Low; EN2 = High; I
OUT
= 100µA to 150mA
EN1 = EN2 = High; I
OUT1
= 150mA, I
OUT2
= 150mA
Ground Current in Shutdown
Ripple Rejection
Current Limit
Output Voltage Noise
Enable Inputs (EN1 / EN2)
Enable Input Voltage
Enable Input Current
Logic Low
Logic High
V
IL
≤
0.2V
V
IH
≥
1.0V
Turn-on Time (See Timing Diagram)
Turn-on Time (LDO1 and 2)
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any T
A
(ambient temperature) is P
D(max)
= (T
J(max)
– T
A
) /
θ
JA
. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.
5. Specification for packaged product only.
6. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal V
OUT
. For outputs below
2.3V, the dropout voltage is the input-to-output differential with the minimum input voltage 2.3V.
Min
-2.0
-3.0
Typ
Max
+2.0
+3.0
Units
%
%
%/V
%/V
%
mV
mV
mV
mV
µA
µA
µA
µA
dB
dB
0.02
0.5
0.1
12
25
35
85
85
150
0.01
70
65
300
550
30
0.3
0.6
2.0
50
75
100
120
120
190
2
EN1 = EN2 = 0V
f = 1kHz; C
OUT
= 1.0µF; C
BYP
= 0.1µF
f = 20kHz; C
OUT
= 1.0µF; C
BYP
= 0.1µF
V
OUT
= 0V
C
OUT
= 1.0 µF; C
BYP
= 0.1µF; 10Hz to 100kHz
950
mA
µV
RMS
0.2
1.1
0.01
0.01
30
100
V
V
µA
µA
µs
C
OUT
= 1.0µF; C
BYP
= 0.01µF
March 2011
5
M9999-032411-C
工业自动化与控制
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
