http://www.luguang.cn
Email: lge@luguang.cn
1. Features and Applications
The LTCA10.7MS2 filters are small,high performance and very thin(1.5mm) chip
devides consisting of 2 ceramic elements for communication equipment.They
are designed on MgTiO
3
ceramic cap package.The filers exhibit flat GDT
characteristic in pass band.The filters are recommended for digital
communication applications and are perfect in hand held cellular phines,pocket
cordless phones, etc.
2. Appearances and Dimendions
Appdarances: smooth surface and clear mark. No visible damage and dirt.
Dimensions: According to Figure 1.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
1
http://www.luguang.cn
Email: lge@luguang.cn
3. Electrical Characteristics
Items
Requirements
A:10.700MHz± 30kHz max.
B:10.670 MHz± 30kHz max.
C;10.730 MHz± 30kHz max.
D;10.640 MHz± 30kHz max
Center
E;10.760 MHz± 30kHz max
Frequency(f
0
) The center point of 3db band width is defined as the center frequency
and identified by the letters:A,B,C,D or E
3dB Bandwidth
20 dB Bandwidth
Insertion loss(at fn)
Ripple(within 3dB Bandwidth)
Spurious Response(9MHz-12MHz)
Input/Output Impedance
4. Rating
Items
4.1
4.2
4.3
4.4
Withstanding Voltage
Insulation Resistance
Operating temperature range
Storage temperature range
230 ±50kHz
570kHz max
6.0dB
1.0dB max
30dB min
330Ω
Spec
DC 50v 1 minutes
100MΩ
min.(DC 10V)
-25
½
+85℃
-40
½
+85℃
5. Measuring method
Measuring Condition
Parts shall be measured under a cndition (Temperature:25±3℃,Humidity;65±5﹪
R.H.)unless the standard condition(Temperature:20±15℃,Humidity;65±20﹪R.H)
is regulated to measure.
Measuring circuit
R1=280Ω±5%, R2=330Ω±5%,Rg=50Ω
①:
Input
C2=10Pf(Including stray capacitance
②:
Ground
and capacitance of RF Voltmeter)
③:Output
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
2
http://www.luguang.cn
Email: lge@luguang.cn
Spec
Meet Table 1
Meet Table 1
Meet Table 1
6. Reliability Specifications
Item
Test Condition
6.1
LowTemp
Stored in _40±3℃for 96 hours, and left at room
Storage
temp.for 1 hour before measurement.
6.2
High Temp
Stored in 85±2℃ for 96 hours, and left at room
Storage
temp.for 1 hour before measurement.
6.3
Stored at40±2,in90½95﹪R.H.for96 hours ,and left
Humidity Test at room temp.for 1 hour before measurement.
6.4
Thermal Shock
6.5
Soldering Test
After temp.cycling of _40℃(30minutes) to +85℃
(30minutes) was performed 5 times, filter shall be
Meet Table 1
measured after being placed in natural condition for
1 hour.
Passed thtough the reflow oven under the following Meet Table 1
condition for 2 times, and left at room temp. for 24
hours before measurement.
Temp. at the surface Time
Of the substeate
Preheat 150±5℃
60½100sec
Peak 235±5℃
Less than 10 sec
Dipped in 35±5℃ solder bath for 3±0.5
Seconds with rosin flrx
The terminals
Shall be at least95
﹪
covered by
solder
Meet Table 1
Meet Table 1
6.6
Solderability
6.7
6.8
Drop test
Vibration
6.9
Board Bending
Free drop to the wood plate from the height of 70
cm for 3 times.
Apply the vibration of weep frequency 10 to
55Hz/minutes,amplitude 1.5mm, duration 2 hours
in each direction of 3 planes.
Mount on a glass-epoxy
board(width=50mm,thickness=1.6mm)then bend it
to 1mm displacement(velocity 1mm/sec) and keep
it for 5 seconds
Mechanical
damage such as
break shall not
occur
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
3
http://www.luguang.cn
Email: lge@luguang.cn
Tablel Characteristics change limit in reliability test
Characteristics
Change Iimit
Insertion Loss
±2dB max
3db bandwidth
±25kHz max
20dB Bandwidth
±60kHz max
7.Packaging
7.1 Reel Dimensions
7.2 Taping Dimensions
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
4
http://www.luguang.cn
7.3 Tape Characteristics
Email: lge@luguang.cn
7.4 Reel Quantity:4000pcs/reel or 1000pcs/reel
7.5 Every reel is vacuum packed.(at 300 Torr of vacuum rate).
8. Notices
8.1 Please avoid cleaning this chip ceramic filter.
8.2 Please contact us if you want to use the product in specital occasion.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
5
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
