CHIP ATTENUATORS
KAMAYA OHM
RAC10 1A, RAC16 1A, 2A
•
Features
1. The RAC10 1A and RAC16 1A, 2A Series are small size chip
attenuators, suitable for high density surface packaging.
2.Suitable for use as DC and up to UHF band frequencies.
3.Similar foot print for chip resistor networks.
4.Standard impedance of 50 ohm and 75 ohm are available up to 600
ohm available on request.
5.Replaces conventional attenuation circuits with one chip in place of
three discrete resistors.
•
Dimensions and Circuit
a
1
2
b
Q
1
W
Q
2
a
RAC16 : Impedance on Termination 1
Attenuation factor on Termination 3
Dot mark on Termination 4
RAC10 : Dot mark on Termination 1
Attenuation factor on Termination 2 to 3
Circuit
4
3
H
4
3
H
W
b
1
2
P
L
RAC16 1A, 2A
Style
Terminal Style
RAC10 1A
C
.2A
A
RAC16 1A
L
1.0±0.05
1.6±0.1
W
1.0±0.05
1.6±0.1
P
4
3
L
RAC10 1A
Unbalanced
Q
0.33±0.10
0.5
±0.1
a
0.15±0.10
0.25±0.10
b
0.25
+0.05
−0.10
0.25
+0.15
−0.10
*P
0.65
0.8
Type
Unit : mm
H
0.35±0.10
0.55
+0.05
−0.10
*Unit weight/pc.
1.1mg
3.5mg
*Values for reference
•
Product Classification
Example
RAC
Product Type
10
Size
Style
1
Characteristic Impedance
A
Circuits
1
Attenuation Factor
Attenuation Factor
Code Attenuation Factor
X
0.5dB
1
1dB
2
2dB
3
3dB
4
4dB
5
5dB
6
6dB
7
7dB
8
8dB
9
9dB
A
10dB
B
11dB
C
12dB
Code
D
13dB
A
E
14dB
F
15dB
C
G
16dB
L
20dB
C
Terminal Style
TH
Packaging
* Packaging
Code
Packaging
B Bulk(Loose Packaging)
TP Paper Tape.
TH Paper Tape.(2mm pitch)
*Refer to Taping and Packaging
information in page 34.35
Product Type
Size
Code Width
10
1.0mm
16
1.6mm
Characteristic Impedance
Code Characteristic Impedance
1
50 ohm
2
75 ohm
Application
RAC10.16
RAC16
RAC10
Circuits
Code Circuits
A Unbalanced
πType
Terminal Style
Termination Style
Application
Without corner RAC16
Type
With corner
RAC10
30
KAMAYA OHM
CHIP ATTENUATORS RAC10 1A, RAC16 1A, 2A
•
Ratings
Style
Characteristic
Impedance
Attenuation
dB
0.5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
20
1
2
3
6
10
1
2
3
6
10
Attenuation Factor Tolerance
dB
±0.1
Attenuation Range
DC≤f≤3GHz
VSWR Voltage
standing wave Ratio
1.1max.
Rated Input Power
mW/element
Category Temperature Range
°C
±0.3
±0.4
±0.75
DC
≤
f
≤
1.5GHz
1.5GHz
<
f
≤
3GHz
1.2max.
1.3max.
RAC10 1A
50 ohm
±0.8
100
−40∼+125
RAC16 1A
50 ohm
RAC16 2A
75 ohm
±2.5
±0.3
±0.3
±0.5
±0.75
±0.75
±0.3
±0.3
±0.5
±0.75
DC
≤
f
≤
3GHz
1.3max.
DC
≤
f
≤
3GHz
1.2max.
*The following information is available.
1. 0dB attenuation.
2. Test methods for Attenuation Factor and VSWR characteristics.
•
Performance Characteristics
Description
0.5−2dB
Characteristic
impedance
50 ohm, 75 ohm
JIS C 5201-1 : 1998
Requirements
3dB−5dB
6dB−20dB
Measuring
Circuit
1
Test Methods
2
R
1
R
2
4
R
2
3
R
L
R
L
=50 ohm
75 ohm
Insulation resistance
Solderability
Resistance to soldering
heat
Rapid change of
temperature
At least 100M ohm
In accordance with Clause 4.17.4.5
Within±0.1dB
Within±0.2dB
Within±0.3dB
50Vd.c., 60s
Clause 4.17 Dip into 235°C solder bath for 2s.
Clause 4.18 Dip into 260°C solder bath for 5s.
No major visible damage.
Within±0.1dB
Within±0.2dB
Within±0.3dB
Clause 4.19 5 cycles between
−55°C
and
+125°C
No major visible damage.
Within±0.1dB
Within±0.2dB
Within±0.3dB
Clause 4.25.1 Rated voltage, 1.5h"ON", 0.5h"OFF" 85°C, 1000h.
Endurance at 85˚C
Bend strength of the
face plating
Within±0.1dB
Within±0.2dB
Within±0.3dB
Clause 4.33 Amount of bend 3mm, 10s
31
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
