REVISIONS
LTR
A
DESCRIPTION
Change to military drawing format. Add vendors CAGE 48726, 34333, and
U4637. Editorial changes throughout.
Change CAGE code to 67268. Add device type 02. Delete vendor CAGE code
U4637. Delete switching circuits. Extensive changes to table I. Editorial
changes throughout.
Add one vendor CAGE U4637 for device types 01 and 02.
Inactivate device type 01 for new design.
Changes in accordance with N.O.R. 5962-R155-92.
Changes in accordance with N.O.R. 5962-R103-95.
Add power dissipation, theta JA, and derating limits for case outline 2 as
specified in paragraph 1.3. - ro
DATE (YR-MO-DA)
87-03-20
APPROVED
M. A. FRYE
B
88-07-20
M. A. FRYE
C
89-05-03
M. A. FRYE
D
E
F
92-12-23
94-04-19
02-02-07
M. A. FRYE
M. A. FRYE
R. MONNIN
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
CURRENT CAGE CODE 67268
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
F
15
F
16
REV
SHEET
F
1
F
2
F
3
F
4
F
5
F
6
F
7
F
8
F
9
F
10
F
11
F
12
F
13
F
14
PREPARED BY
DONALD R. OSBORNE
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D. A. DiCENZO
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
APPROVED BY
N. A. HAUCH
MICROCIRCUIT, LINEAR, REGULATING PULSE-
WIDTH MODULATOR, MONOLITHIC SILICON
DRAWING APPROVAL DATE
86-02-19
AMSC N/A
REVISION LEVEL
F
SIZE
A
SHEET
CAGE CODE
14933
1 OF
16
85515
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E134-02
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
85515
01
V
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
Generic number
1526
1526A
Circuit function
Pulse-width modulator
Pulse-width modulator
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
V
2
Descriptive designator
GDIP1-T18 or CDIP2-T18
CQCC1-N20
Terminals
18
20
Package style
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Input voltage (V
IN
) .................................................................. 40 V dc
Collector supply voltage (V
C
) ................................................. 40 V dc
Logic inputs ............................................................................ -0.3 V dc to +5.5 V dc
Analog inputs ......................................................................... -0.3 to +V
IN
Output current (I
SOURCE
or I
SINK
) .........................................
±200
mA
Reference output current ........................................................ 50 mA
Maximum power dissipation (P
D
) (T
A
= +25°C):
Case V ................................................................................ 1,000 mW 1/ 2/
Case 2 ................................................................................ 1,500 mW 1/ 2/
Maximum junction temperature (T
J
) ....................................... +150°C
Storage temperature range .................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds) ............................ +300°C
Thermal resistance, junction-to-case (
θ
JC
) ............................ See MIL-STD-1835
Thermal resistance, junction-to-ambient (
θ
JA
):
Case V ................................................................................ 100°C/W
Case 2 ................................................................................ 80°C/W
_____
1/ For case V, derate at 10 mW/°C for ambient temperatures above +50°C. For case 2, derate at 13 mW/°C for
ambient temperatures above +25°C.
2/ Must withstand the added P
D
due to short circuit current; e.g., I
OS
.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
85515
SHEET
F
2
1.4 Recommended operating conditions.
Input voltage (V
IN
):
Device type 01 .................................................................... 8 V dc to 35 V dc
Device type 02 .................................................................... 7 V dc to 35 V dc
Collector supply voltage (V
C
) ................................................. 4.5 V dc to 35 V dc
Ambient operating temperature (T
A
) ...................................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
85515
SHEET
F
3
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Logic diagrams. The logic diagrams shall be as specified on figure 2.
3.2.4 Switching waveforms. The switching waveforms shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
85515
SHEET
F
4
TABLE I. Electrical performance characteristics.
Conditions 1/
-55°C
≤
T
A
≤
+125°C
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits 2/
Min
Max
Unit
Power consumption section
Standby current
I
IN
SHUTDOWN = 0.4 V,
V
IN
= 35 V
Reference section
Reference output voltage
V
REF
I
LOAD
= 0 mA
1
2,3
Line regulation
V
RLINE
V
IN
= 8 V to 35 V
V
IN
= 7 V to 35 V
Load regulation
V
RLOAD
I
LOAD
= 0 mA to -20 mA
1,2,3
1,2,3
01
02
01
02
Short circuit current
I
OS
V
REF
= 0 V, t
≤
25 ms
1,2,3
01
02
Output noise voltage
N
O
∆V
IN
/
∆V
REF
Oscillator section 4/
Initial accuracy
A
CC
R
T
= 4.12 kΩ
±0.1%,
C
T
= 0.01
µF ±0.1
%,
R
deadtime
= 0
Ω
Voltage stability
∆f
OSC
V
IN
= 8 V to 35 V
5,6
4,5,6
02
All
36
44
1
%
4
All
36.8
43.2
kHz
f
O
= 10 Hz to 10 kHz 3/
T
A
= +25°C
Ripple rejection
V
IN
= 15 V,
+1 V rms at 2.4 kHz
4
4,5,6
01
02
50
50
dB
4
All
-125
-100
200
µVrms
All
4.95
4.90
5.05
5.10
20
10
30
20
mA
mV
mV
V
1,2,3
01
02
30
20
mA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
85515
SHEET
F
5
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
