The RP15-OFW series are SMD open frame ultraminiature power DC/DC converters in a case half the
size of industry standard 15W converters. The converters use solder ball pins to enable SMD
mounting and can be reflow soldered. Despite their small size, the RP15-OFW converters are fully
specified devices with output currents up to 4 Amps, no minimum load, 2250VDC isolation and low
ripple/noise figures. The outputs are also fully protected against short circuits, overcurrent and
overvoltage. The RP15-0FW series will find many uses in telecommunications and other demanding
applications where price, board space or board height is at a premium.
3
EAR
rranty
Selection Guide
Part Number
RP15-243.3SOFW
(3)
RP15-2405SOFW
(3)
RP15-2412SOFW
(3)
RP15-2415SOFW
(3)
RP15-483.3SOFW
(3)
RP15-4805SOFW
(3)
RP15-4812SOFW
(3)
RP15-4815SOFW
(3)
Input
Voltage Range
[VDC]
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
Output
Voltage
[VDC]
3.3
5
12
15
3.3
5
12
15
Output
Current
[mA]
4000
3000
1300
1000
4000
3000
1300
1000
Input
(1)
Efficiency
(1)
Current
typ.
[mA]
[%]
647
85
718
87
756
86
727
86
324
85
359
87
378
86
363
86
Max. Capacitive
Load
(2)
[µF]
12000
6000
1000
660
12000
6000
1000
660
Notes:
Note1: Values at nominal input voltage and no load/full load.
Note2: Test by minimum Vin and constant resistor load.
E196683
UL60950-1 Certified
Model Numbering
RP15-__ __ SOFW/_
Input Voltage
Output Voltage
Single
Ordering Examples
RP15-4805SOFW = 48V 4:1 Input, 5V Output, No CTRL pin, No Trim Pin
RP15-4805SOFW/P = 48V 4:1 Input, 5V Output, Positive Logic CTRL pin and Trim pin fitted.
RP15-243.3SOFW/N = 24V 4:1 Input, 3.3V Output, Negative Logic CTRL pin and Trim pin fitted
Notes:
Note3: No suffix for standard part without Trim or CTRL
add suffix “P” for CTRL function with positive logic (1=ON, 0=OFF) and trim pin
add suffix “N” for CTRL function with negative logic (0=ON, 1=OFF) and trim pin
Control Logic
(3)
www.recom-power.com
REV.: 1/2016
PD-1
RP15-OFW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
BASIC CHARACTERISTICS
Parameter
Input Voltage Range
Series
Condition
nom. Vin = 24V
nom. Vin = 48V
Vin = 24V
DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
Min.
9DC
18VDC
Typ.
24VDC
48VDC
8VDC
Max.
36VDC
75VDC
9VDC
18VDC
Under Voltage Lockout (UVLO)
Vin = 48V
Input Filter
Input Reflected Ripple
(4)
Input Surge Voltage
Start-up time
Operating Frequency Range
Minimum Load
Optional Output Trim
Ripple and Noise
Remote ON/OFF
(5)
Negative Logic
Input current of Remote pin (CTRL)
(5)
16VDC
Pi-Type
30mAp-p
50VDC
100VDC
30ms
30ms
315kHz
360kHz
0%
±10.0%
100mVp-p
Open or 3.0V < Vr < 15V
Short or 0V < Vr < 1.2V
Short or 0V < Vr < 1.2V
Open or 3.0V < Vr < 15V
2.5mA
-0.5mA
+1.0mA
350kHz
400kHz
385kHz
440kHz
nominal Vin and full load
Vin = 24V, 100ms max.
Vin = 48V, 100ms max.
Power up
Remote ON/OFF
3.3Vout, 5Vout
12Vout, 15Vout
full load
20MHz bandwidth, with 1μF M/C X7R and a 10μF T/C
Positive Logic
DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
DC-DC OFF
DC-DC ON
Notes:
Note4: Simulated source impedance of 12μH. 12μH inductor in series with +Vin.
Note5: If no suffix is specified, the control and trim pins will be omitted. If fitted, the ON/OFF control
function can be positive or negative logic. The pin voltage is referenced to -Vin.
RP15-2405SOFW
95
90
85
Efficiency vs. Output Current
90
85
Efficiency vs. Input Voltage
Efficiency [%]
80
75
70
65
60
55
50
45
40
10
20
30
40
50
60
70
80
9Vin
24Vin
36Vin
90
100
Efficiency [%]
80
75
70
65
60
9
12
15
18
21
24
27
30
33
36
Output Current [%]
Input Voltage [VDC]
continued on next page
PD-2
REV.: 1/2016
www.recom-power.com
RP15-OFW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
Series
RP15-4805SOFW
95
90
85
Efficiency vs. Output Current
95
90
Efficiency vs. Input Voltage
Efficiency [%]
80
75
70
65
60
55
50
45
40
10
20
30
40
50
60
70
80
18Vin
48Vin
75Vin
90
100
Efficiency [%]
85
80
75
70
65
18
24
30
36
42
48
54
60
66
75
Output Current [%]
Input Voltage [VDC]
REGULATIONS
Parameter
Output Voltage Accuracy
Voltage Adjustability
Line Voltage Regulation
Load Voltage Regulation
Transient Response recovery time
low line to high line at full load
0% to 100% load
25% load step change
Condition
Value
±1%
±10%
±0.2%
±0.2%
250μs
External Output Trimming
Output Voltage Trimming
Single output Powerline Plus converters offer the feature of trimming the output voltage over a certain range around the nominal value by using
external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing
these trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the
resistor required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below.
Trim up
6
RU
5
4
5
Trim down
RD
RP15-xx3.3SOF
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
3.333
385.07
1
3.267
116.72
2
3.366
191.51
2
3.234
54.78
3
3.399
126.99
3
3.201
34.13
4
3.432
94.73
4
3.168
23.81
5
3.465
75.37
5
3.135
17.62
6
3.498
62.47
6
3.102
13.49
7
3.531
53.25
7
3.069
10.54
8
3.564
46.34
8
3.036
8.32
9
3.597
40.96
9
3.003
6.60
10
3.63
36.66
10
2.97
5.23
%
Volts
kOhms
%
Volts
kOhms
continued on next page
www.recom-power.com
REV.: 1/2016
PD-3
RP15-OFW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
RP15-xx05SOF
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
5.05
253.45
1
4.95
248.34
2
5.10
125.70
2
4.90
120.59
3
5.15
83.12
3
4.85
78.01
4
5.20
61.82
4
4.80
56.71
5
5.25
49.05
5
4.75
43.94
6
5.30
40.53
6
4.70
35.42
7
5.35
34.45
7
4.65
29.34
8
5.4
29.89
8
4.60
24.78
9
5.45
26.34
9
4.55
21.23
10
5.50
23.50
10
4.50
18.39
%
Volts
kOhms
%
Volts
kOhms
Series
RP15-xx12SOF
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
12.12
203.22
1
11.88
776.56
2
12.24
99.06
2
11.76
380.72
3
12.36
64.33
3
11.64
248.78
4
12.48
46.97
4
11.52
182.81
5
12.60
36.56
5
11.40
143.22
6
12.72
29.61
6
11.28
116.83
7
12.84
24.65
7
11.16
97.98
8
12.96
20.93
8
11.04
83.85
9
13.08
18.04
9
10.92
72.85
10
13.20
15.72
10
10.8
64.06
%
Volts
kOhms
%
Volts
kOhms
RP15-xx15SOF
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
15.15
161.56
1
14.85
818.22
2
15.3
78.22
2
14.70
401.56
3
15.45
50.45
3
14.55
262.67
4
15.60
36.56
4
14.40
193.22
5
15.75
28.22
5
14.25
151.56
6
15.90
22.67
6
14.10
123.78
7
16.05
18.70
7
13.95
103.94
8
16.20
15.72
8
13.80
89.06
9
16.35
13.41
9
13.65
77.48
10
16.50
11.56
10
13.50
68.22
%
Volts
kOhms
%
Volts
kOhms
PROTECTIONS
Parameter
Short Circuit Protection (SCP)
Over Voltage Protection (OVP)
Over Load Protection (OLP)
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Notes:
Note6: This power module is not internally fused. An input line fuse must always be used.
PD-4
REV.: 1/2016
www.recom-power.com
Condition
3.3Vout
5Vout
Zener Diode Clamp
12Vout
15Vout
% of Iout rated, Hiccup mode
I/P to O/P
500VDC
Value
continuous, automatic recovery
3.7 - 5.4V
5.6 - 7.0V
13.8 - 17.5V
16.8 - 20.5V
150% typ.
2.25kVDC/1 minute
1GΩ min.
1500pF typ.
RP15-OFW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
ENVIRONMENTAL
Parameter
Reflow Soldering Process
Moisture sensitivity level (MSL)
Operating Temperature Range
Temperature Coefficient
Thermal Impedance
Operating Humidity
Thermal Shock
Vibration
MTBF
MIL-HDBK-217F
Bellcore TR-NWT-000332
(7)
RP15-4805SOFW
100
80
60
40
20
0
-40
Series
Condition
Value
IPC J-STD-020D
IPC J-STD-03B level 2a
without derating
with derating
Natural convection (20LFM)
-40°C to +70°C
-40°C to +120°C
±0.02%/°C max.
18.2°C/Watt
5% - 95% RH
MIL-STD-810F
MIL-STD-810F
2444 x 10
3
hours
1322 x 10
3
hours
Derating Graph
(8)
Output Power [%]
-20
0
20
40
60
80
100 120
Ambient Temperature [°C]
Notes:
Note7: BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C.
MIL-HDBK 217F Notice 2. Ta = 25°C, full load, (Ground Benign, controlled environment).
Note8: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-
number not shown here please contact our technical support service at techsupportAT@recom-power.com
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
UL General Safety
Report / File Number
E196683
Standard
UL60950-1 1st Ed.: 2003
C22.2 No. 60950 1st. Ed.: 2003
EMC Compliance
EMI Standard
(9)
Radiated Immunity
Fast Transient
(10)
Surge
(10)
Conducted Immunity
Condition
with external filter
10 V/m
±2kV
±1kV
10 Vr.m.s
Standard / Criterion
EN55022, Class A, Class B
EN61000-4-3, Criteria A
EN61000-4-4, Criteria A
EN61000-4-5, Criteria A
EN61000-4-6, Criteria A
Notes:
Note9: The standard modules meet EMI Class A or Class B with external components, see filter suggestions below.
Note10: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Recom
51单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
