T
JS
-T
18
S-
TS series
Proportional miniature thumb controls •
non-contacting Hall effect technology
DISTINCTIVE FEATURES
One or two axis
Analog, PWM or USB outputs
IP67 Above panel sealing mounting
Rear or drop-in mounting
Pushbutton option
ENVIRONMENTAL SPECIFICATIONS
• Operating Temperature: -40 °C to +85 °C (-40 °F to +185 °F)
• Storage Temperature: -40 °C to +85 °C (-40 °F to +185 °F)
• Above Panel Sealing: IP67, IP69K
1
(subject to mounting style & final
specifications)
• EMC Immunity Level: EN61000-4-3
• EMC Emissions Level: EN61000-6-3:2001
• ESD: EN61000-4-2
SENSOR SPECIFICATIONS
• Technology: Hall effect sensors, single or dual
• Supply Voltage Range: 5.00 V ± 0.01 VDC
• Supply Current: 11 mA max
• Ratiometric Output Options: See options
• Reverse Polarity max: -10 V
• Transient overvoltage max: 16 V
• Start-up time: 15 ms max
• Output Impedance: 2Ω
• Return to Center Voltage Tolerance: ± 200 mV initial
The company reserves the right to change specifications without notice.
1
JOYSTICKS
04
JOYSTICKS
TS series
Proportional miniature thumb controls •
non-contacting Hall effect technology
MECHANICAL SPECIFICATIONS
• Operating Force: 3.1 N ± 0.5 N (0.70 lbf ± 0.11 lbf)
2
• Maximum Vertical Load: 200 N (45 lbf)
2
• Maximum Horizontal Load: 150 N (33.7 lbf)
2
PUSHBUTTON SWITCH
SPECIFICATIONS
(OPTION 6 HANDLE)
• Electrical Life: 100,000 cycles
• Rating: 50 mA, 12 VDC.
• Terminal: Brass with silver plating
• Contact Resistance: 100 mΩ max
• Insulation Resistance: 100 MΩ min. 500 VDC
• Dielectric Strength: 250 VAC /1 minute
• Contact Arrangement: 1 pole 1 throw
• Stop Strength: Max 3 kgf vertical static load for 15
seconds
• Operating Temperature: -25 °C to +70 °C
(-4 °F to +158 °F)
• Storage Temperature: -30 °C to +85 °C
(-22 °F to +158 °F)
• Vibration Resistance: MIL-STD-202F METHOD
201A
• Shock Resistance: MIL-STD-202F METHOD 213B
• Mechanical Angle of Movement: 50° X & Y axis (subject to
limiter plate)
• Expected Life: 1 million cycles
• Mass/Weight: 18.25 g ± 5.0 g (0.64 oz ± 0.18 oz)
• Lever Action (centering): Spring
All options are IP68 and IP69K rated, however drop-in mounting does not prevent
panel ingress.
2
Force applied to the top of the castle cap.
1
MATERIALS
• Body: Glass filled nylon
• Threaded Housing: Black oxide plated brass
• Boot: Silicone
• Handles:
1, 2, 3, E, F, G
- Glass filled nylon
4, 5, 6, 7, 8
- Silicone
B, C, D
- Thermoplastic elastomer
H
- Polycarbonate
APEM products may be recycled at end-of-life for the re-claiming of valuable metal
components.
LED SPECIFICATIONS
(OPTION H HANDLE)
LED CONTROL
1 – ON, driven by
joystick supply
voltage
2 – User
controlled
OPERATING VOLTAGE
-
OPERATING CURRENT
6 mA
CONNECTIONS
WIRING SPECIFICATION
(Termination options 1 & 2)
Black
Red
Blue
Yellow
Orange
Blue/White Stripe
Yellow/Black Stripe
Red/White Stripe
Black/White Stripe
1
2
5V
6 mA
Ground & button common,
or LED common
Power (5 V)
1
X axis output (alpha)
Y axis output (alpha)
Pushbutton switch (option 6 handle)
or LED supply (option H handle)
2 2
X axis output (beta)
Y axis output (beta)
Power (5 V) (beta)
Ground (beta)
Hall sensor and LED supply (LED control option 1)
User controllable (LED control option 2)
2
TS series
Proportional miniature thumb controls •
non-contacting Hall effect technology
NEW OPTIONS AVAILABLE
PLASTIC THREADED HOUSING
LED ILLUMINATION OPTION H HANDLE
MOUNTING
PLASTIC HOUSING - REAR MOUNT OPTION CUTOUT
PLASTIC HOUSING - DROP-IN
PLASTIC HOUSING - DROP-IN OPTION CUTOUT DIMENSIONS
CUTOUT
Ø2.87
(0.113)
Ø25.65
(1.01)
4 x PUSH IN CONNECTORS
PLASTIC HOUSING - REAR MOUNT OPTION CUTOUT
4 x 1/2 FH SS PHIL SCREW
CHAMFERED
FOR #4 FLAT
HEAD SCREW
(4 PLACES)
Ø2.87
(0.113)
Ø25.65
(1.01)
24.64
(0.97)
DROP-IN
BEZEL
24.64
(0.97)
1.00 (0.04) x 45º
CHAMFER
O-RING
24.64
(0.97)
24.64
(0.97)
REAR MOUNT
BEZEL
• The under panel depth for the Drop-in
configuration is 16.02 mm (0.631 in).
• The maximum panel thickness for the Rear
Mount configuration is 2.032 mm (0.08 in).
• Mounting screws can be driven to a
recommended torque of 4 lbf.
METAL THREADED HOUSING - DROP-IN OPTION CUTOUT DIMENSIONS
METAL THREADED HOUSING - DROP-IN CUTOUT
R17.17 x 2
(0.063)
2X R1.6
.063
11.94
.470
PLASTIC THREADED HOUSING - DROP-IN CUTOUT
FIG. 5
R17.17
2X (0.063)
11.94
.470
2X R1.6
.063
11.94
(0.47)
11.94
(0.470)
NUT
25.02
.985
Ø25.02
(0.985)
25.02
.985
(
25.02
0.985)
• The under panel depth for the Metal Threaded
Housing configuration is 14.55 mm (0.573 in).
• Mounting nut can be tightened to a
recommended torque of 10 lbf.
• The under panel depth for the Plastic Threaded
Housing configuration is 14.55 mm (0.573 in).
• Mounting nut can be tightened to a
recommended torque of 10 lbf.
3
JOYSTICKS
JOYSTICKS
TS series
Proportional miniature thumb controls •
non-contacting Hall effect technology
BUILD YOUR PART NUMBER
TS
SERIES
MOUNTING OPTIONS
TERMINATION
2
LIMITER
N
D
R
A
T
P
HANDLE
1
None
Drop-in
Rear mount
Drop-in and Rear Mount
Threaded housing, Metal
Threaded housing, Plastic
1
2
3
4
5
22 AWG 25 cm PTFE
2-1
28 AWG 25 cm PTFE
2-2
72” Overmold Cable with
USB Male Type Connector
2.54 mm (0.100”)
Pitch TE Connector
2.54 mm (0.100”)
Pitch TE Connector with
10” Mating Harness
U
S
G
P
Single axis
Square
Guided feel
Plus
0
1
2
3
4
5
None
Castle
Winged Hat
Conical
Finger Tip
Round Jog
6
7
8
A
B
C
Pushbutton
1
Mushroom
1
Low Profile
1
Handles 1, 2, 3
Castle, elastomer
Winged Hat,
elastomer
D
E
F
G
H
Conical, elastomer
Quadcave
Puck
Roller
Castle, LED
illumination
OUTPUT OPTIONS
4
LED CONTROL
00
01
02
03
04
05
0 V to 5 V
0.25 V to 4.75 V
0.5 V to 4.5 V
1 V to 4 V
0 V to 5 V - Sensor 1
0 V to 5 V - Sensor 2
0.25 V to 4.75 V - Sensor 1
0.25 V to 4.75 V - Sensor 2
06
07
08
09
10
0.5 V to 4.5 V - Sensor 1
0.5 V to 4.5 V - Sensor 2
1 V to 4 V - Sensor 1
1 V to 4 V - Sensor 2
0 V to 5 V - Sensor 1
5 V to 0 V - Sensor 2
0.5 V to 4.5 V - Sensor 1
4.5 V to 0.5 V - Sensor 2
0.25 V to 4.75 V - Sensor 1
4.75 V to 0.25 V - Sensor 2
11
12
13
14
15
1 V to 4 V - Sensor 1
4 V to 1 V - Sensor 2
Customer specified
PWM
3
USB (Game Controller)
Joyball (Cursor
emulation)
BLANK
1
2
No illumination
ON, driven by joystick
supply voltage
6
User controlled
7
POWER SUPPLY OPTIONS
LED COLOR
A
B
Single
Independent
5
BLANK
BB
RR
No illumination
Blue
Red
Pushbutton, Mushroom and Low profile handle not available with T (threaded housing, metal)
or P (threaded housing, plastic),
2-1
Wires are thick, robust, and best suited for stand alone applications.
2-2
Wires are thin and best suited for tightly constrained wire routing.
3
Contact factory for PWM configuration.
4
Output voltage is ratiometric to supply voltage.
5
Only available on dual output. Not available with Handle 6 (Pushbutton). Not available with termination options 4 or 5.
6
LED control is driven by joystick supply voltage. Illumination is constantly on
7
LED requires independent 5V supply. Illumination is user controlled.
1
4
TS series
Proportional miniature thumb controls •
non-contacting Hall effect technology
PLASTIC HOUSING
17.17
(0.676)
PIN INDICATES
+Y DIRECTION
19.20
(0.75)
23.00
(0.91)
TOP VIEW
33.27
(1.31)
10.00 - 13.00
(0.40 - 0.50)
25.40
(1.00)
29.70
(1.17)
Top view
17.17
(0.676)
METAL THREADED HOUSING
33.12
(1.304)
10.00 - 13.00
(0.40 - 0.50)
Ø32.77
(1.29)
Ø24.89
(0.98)
LOCATING FEATURE, Y+
Ø24.89
(0.98)
17.17
(0.676)
11.81
(0.465)
Ø24.89
(0.98)
17.17
(0.676)
33.12
(1.304)
10.00 - 13.00
(0.40 - 0.50)
Bottom view
17.16
.68
11.81
(0.465)
33.12
(1.304)
10.00 - 13.00
(0.40 - 0.50)
Ø32.77
(1.29)
LOCATING FEATURE, Y+
Ø32.77
11.81
(1.29)
(0.465)
34.84
1.37
10.1
.40
LOCATING FEATURE, Y+
MINIMUM PANEL TH
Top view
32.77
1.29
PLASTIC THREADED HOUSING
LOCATING FLAT, Y+
35.56
1.40
17.16
.68
Bottom view
34.84
1.37
10.1
.40
MINIMUM PANEL THICKNESS: .125"
32.77
1.29
Top view
35.56
1.40
17.16
.68
LOCATING FLAT, Y+
34.84
1.37
10.1
.40
MINIMUM PANEL T
32.77
1.29
35.56
1.40
LOCATING FLAT, Y+
5
JOYSTICKS
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
