TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-069
REVISION
Clincher™ Latch Headers
1 of 8
AUTHORIZED BY
DATE
D
31 Aug 06
J. Spickler
CLASSIFICATION
UNRESTRICTED
1.0
OBJECTIVE
This specification defines the performance, test, quality, and reliability requirements of Clincher Latch Headers.
2.0
SCOPE
This specification is applicable to the termination characteristics of the Clincher Latch Header when mated with
the FCI Clincher Latching Receptacle. This product provides board to flat cable and board to flex interconnect
capabilities in vertical and right angle single row configurations on 0.100" pitch.
3.0
GENERAL
This document is composed of the following sections:
Paragraph
1.0
2.0
3.0
4.0
5.0
5.1
5.2
5.3
5.4
6.0
7.0
8.0
9.0
9.1
9.2
9.3
9.4
9.5
9.6
CHART I
TABLE I
APPLICABLE DOCUMENTS
4.1
Specifications
4.1.1 Engineering drawings
4.1.2 Process drawings
4.2
Military Standards/Specifications
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.3
MIL-STD-202: Test methods for electronic and electrical component parts.
MIL-STD-1344: Test methods for electrical connectors
MIL-C-45662: Calibration system requirements
MIL-G-45204: Gold Plating, Electrodeposited
MIL-P-45209: Palladium Plating, Electrodeposited
MIL-P-81728: Plating, Tin-Lead, Electrodeposited
Title
Objective
Scope
General
Applicable Documents
Requirements
Qualification
Material
Finish
Design and Construction
Electrical Characteristics
Mechanical Characteristics
Environmental Conditions
Quality Assurance Provisions
Equipment Calibration
Inspection Conditions
Sample Quantity and Description
Acceptance
Qualification Testing
Requalification Testing
IR Reflow Profile
Qualification Testing Matrix
4.0
Federal Specifications
FCI
GS-01-001
Copyright
Form E-3334
Rev E
PDM: Rev:D
STATUS:
Released
Printed: Nov 28, 2010
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-069
REVISION
Clincher™ Latch Headers
2 of 8
AUTHORIZED BY
DATE
D
31 Aug 06
J. Spickler
CLASSIFICATION
UNRESTRICTED
4.3.1 QQ-N-290
4.4
Nickel Plating (Electrodeposited)
Other Standards/Specifications
4.4.1 UL-94-V0: Flammability
4.4.2 ASTM B-159: Phosphor Bronze Wire
4.4.3 FCI BUS-19-002: Solderability of Plated Materials or Contacts
4.5
FCI Lab Reports - Supporting Data
4.5.1 EL-95-09-037
EL-96-01-040
5.0
REQUIREMENTS
5.1
Qualification
Connectors furnished under this specification shall be capable of meeting the qualification test
requirements specified herein.
5.2
Material
The material for each component shall be as specified herein or equivalent.
5.2.1 Pins: Pins shall be Phosphor Bronze Alloy UNS C51000 drawn wire in accordance with ASTM B-
159.
5.2.3 Insulator: High temperature resin with a flame retardant rating of UL-94-V0.
5.3
Finish
The finish of the pins shall be as specified herein for the options as listed in the product drawings under
consideration.
5.3.1 Gold Finish: As defined by product drawings, the pins will be plated with the specified thickness of
gold per MIL-G-45204, Type II, Grade C over 50 u" nickel per QQ-N-290, Class 2.
5.3.2 Tin Lead Finish: As defined by product drawings, the pins will be plated with 120µ" minimum
thickness of 93/7 tin lead per MIL-P-81728 over 50µ” of nickel per QQ-N-290,
Class 2.
5.3.3 GXT (Palladium Alloy) Finish: As defined by product drawings, the pins will be plated with a thin
gold flash over the specified thickness of palladium alloy per MIL-P-
45209 over 50 u" of nickel per QQ-N-290, Class 2.
Copyright
Form E-3334
Rev E
FCI
GS-01-001
PDM: Rev:D
STATUS:
Released
Printed: Nov 28, 2010
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-069
REVISION
Clincher™ Latch Headers
3 of 8
AUTHORIZED BY
DATE
D
31 Aug 06
J. Spickler
CLASSIFICATION
UNRESTRICTED
5.4
Design and Construction
Connectors shall be of the design, construction and physical dimensions specified on the applicable
product drawings.
6.0
ELECTRICAL CHARACTERISTICS
6.1
Insulation Resistance - The insulation resistance of the unmated connector shall not be less than 5,000
megohms when measured in accordance with MIL-STD-202, Method 302. The
following details shall apply:
a. Test Voltage: 500 V DC.
b. Electrification Time: One minute.
c. Points of Measurement: Between adjacent pins.
6.2 Dielectric Withstanding Voltage - There shall be no evidence of arc-over, insulation breakdown or
excessive leakage current ( > 1 milliampere) when the unmated connector
is tested in accordance with MIL-STD-1344, Method 3001.1. The
following details shall apply:
a.
b.
c.
d.
Test Voltage: 1500 Volts ( DC, RMS or AC, 60 Hz).
Test Duration: 60 seconds.
Test Condition: 1 (760 Torr - sea level).
Points of Measurement: Between adjacent pins.
6.3 Capacitance - The capacitance between adjacent pins in an unmated connector shall not exceed 2.0 picofarads
when measured in accordance with MIL-STD-202, Method 305, at a frequency of 100 kilohertz.
7.0
MECHANICAL CHARACTERISTICS
7.1 Pin Retention - Individual pins shall withstand an axial load of 2.0 pounds minimum applied at a rate of 0.2
inches/minute without dislodging from the insulator. Reference MIL-STD-1344A, Method
2007.1.
Receptacle, the latch
7.2 Latch Retention - When properly mated and latched with the Clincher Latching
shall withstand an axial load of 6.0 pounds minimum applied at a rate of 0.2
inches/minute without unmating.
8.0
ENVIRONMENTAL CONDITIONS
After exposure to the following environmental conditions in accordance with the specified test procedure and
details, the product shall show no physical damage and shall meet the electrical requirements per paragraph 6.0
as specified in the Table l test sequences. Connectors shall be unmated during exposure.
Copyright
Form E-3334
Rev E
FCI
GS-01-001
PDM: Rev:D
STATUS:
Released
Printed: Nov 28, 2010
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-069
REVISION
Clincher™ Latch Headers
4 of 8
AUTHORIZED BY
DATE
D
31 Aug 06
J. Spickler
CLASSIFICATION
UNRESTRICTED
8.1
Thermal Shock - MIL-STD-202, Method 107.
a.
b.
c.
d.
Test Condition: B ( 25, 1 hour cycles ).
Temperature Range: -65 to +105 deg. Celsius.
Time at Each Temperature: 30 minutes.
Transfer Time - 5 minutes, maximum.
8.2
High Temperature Life - MIL-STD-202, Method 108.
a. Test Temperature: 105 deg. Celsius.
b. Test Duration: B (250) hours.
8.3
Solderability - FCI BUS-19-002 & MIL-STD-202, Method 208C.
a.
Contact areas evaluated shall meet the Method 208 requirements.
8.4
Resistance to Solder Heat - MIL-STD-202, Method 210B.
a. Test Condition: E
b. There shall be no evidence of physical or mechanical damage.
8.5
IR Reflow - Test IR profile per Chart I. There shall be no evidence of physical or mechanical damage after
reflow.
a. Peak Temperature: 245 +/- 5 deg. Celsius.
9.0
QUALITY ASSURANCE PROVISIONS
9.1
Equipment Calibration - All test equipment and inspection facilities used in the performance of any test
shall be maintained in a calibration system in accordance with MIL-C-45662 and
ISO 9000.
Inspection Conditions - Unless otherwise specified herein, all inspections shall be performed under the
following ambient conditions:
a. Temperature: 25 +/- 5 degrees Celsius
b. Relative Humidity: 30 to 60%
c. Barometric Pressure: Local ambient
9.3
Sample Quantity and Description
9.3.1 The qualification samples shall consist of nine of the eight position size connectors of the particular
type being tested.
9.2
Copyright
Form E-3334
Rev E
FCI
GS-01-001
PDM: Rev:D
STATUS:
Released
Printed: Nov 28, 2010
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
GS-12-069
REVISION
Clincher™ Latch Headers
5 of 8
AUTHORIZED BY
DATE
D
31 Aug 06
J. Spickler
CLASSIFICATION
UNRESTRICTED
9.4
Acceptance
9.4.1
Electrical and mechanical requirements placed on test samples as indicated in paragraphs 6.0
and 7.0 shall be established from test data using appropriate statistical techniques or shall
herwise be customer specified, and all samples tested in accordance with this product
specification shall meet the stated requirements.
9.4.2 Failures attributed to equipment, test setup or operator error shall not disqualify the product. If
product failure occurs, corrective action shall be taken and samples submitted for qualification.
9.5
Qualification Testing - Qualification testing shall be performed on samples produced with equipment and
procedures normally used in production. The test sequence shall be as shown in
Table I.
Requalification Testing - If any of the following conditions occur, the responsible product engineer shall
initiate requalification testing consisting of all applicable parts of the qualification
test matrix, Table I.
a. A significant design change is made to the existing product which impacts the
product form, fit or function. Examples of significant changes shall include,
but not be limited to, changes in the plating material composition or thickness,
contact force, contact surface geometry, insulator design, contact base
material, or contact lubrication requirements.
b. A significant change is made to the manufacturing process which impacts the
product form, fit or function.
c. A significant event occurs during production or end use requiring corrective
action to be taken relative to the product design or manufacturing process.
9.6
Copyright
Form E-3334
Rev E
FCI
GS-01-001
PDM: Rev:D
STATUS:
Released
Printed: Nov 28, 2010
.
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
