PIEZO
■
MODEL:
ULTRASONIC
SENSOR
SPECIFICATIONS
T/R40-14C0-01
SPECIFICATION:
40±1.0KHz
≥150mV
(FIG4 SIMULATION TEST CIRCUIT)
≤1.2ms
120±15
60±10
1800±15%
160(40KHz) Pulse width 0.5ms, interval 20ms
50000h
-40½+80
-40½+85
(FIG4 SIMULATION TEST CIRCUIT)
■
ELECTRICAL
1
Center frequency(KHz)
2
3
Echo Sensitivity
Decay Time
Directivity (deg) X-axis
Directivity (deg) Y-axis
4
5
6
7
8
9
10
Capacitance
(pF)
Allowable Maximum Input
Voltage(Vp-p)
Mean Time To Failure
Operating Temperature(
℃
)
Storage temperature(
℃
)
■
APPEARANCE
AND DIMENSIONS
TOP VIEW
BOTTOM VIEW
φ 1 4. 0± 0. 3
12 .0 ±0 .3
6. 0± 0. 3
9 .0 ± 0. 3
8. 0± 1 .0
1 1. 0± 1. 0
2 -φ 0. 6± 0 .0 5
5. 0 ±0 .5
■ENVIRONMENT
CHARACTERISTICS
CONDITIONS
High and low temperature
(from-40℃ to +80℃ at a relative humidity of 30%)
Humidity of 10% to 90%
at the temperature of 25℃
Storage at +85℃ for 96 hours and at -40℃ for
96hours followed by a normalization period at 25℃. As
shown in FIG1.
Operation at 95% relative humidity and 40℃ for 100
hours, followed by a normalization period of 24hours at
30% and 25℃.As shown in FIG2.
Vibration at 10Hz to 55Hz ,1.5mm amplitude. 1
minute sweep.
X,Y,Z,3 each axis for 3 hours.
Shock: After impact of 50G is applied as following X,Y
axis/3 cycle/each direction.
All sensitivity shall be within 30% of the
specified values after the device is subjected
to any or all of the conditions.
STANDARDS
Sensitivity shall not change by more than
30% all of the conditions.
F IG 1
T E M P . T E S T
+85℃ +3℃ /-0℃
+25℃ +10℃ /-5℃
+25℃ +10℃ /-5℃
-40℃ +0/-3℃
1hour
96hours
2hours
96hours
1hour
F IG
2 T E M P . /H U M ID I T Y T E S T
40℃ 95％ RH
25℃ 30％ RH
100hours
15min
24hours
F IG 3 V IB R A T IO N T E S T
2
WATER PROOF TYPE
NOTE:
1. DESIGN RESTRICTION/PRECAUTIONS
■
This sensor is designed for use in air environment. Do not use it in liquid.
■
In the case where secondary accidents due to operation failure or malfunctions can be anticipated,
add a fail safe function to the design.
■
In the case where this sensor is to be hold in housing, use soft buffer between sensor and housing.
The front part of this sensor must be free to vibrate. If this part is hold, its characteristics will vary.
SENSOR
THE FRONT PART
HOUSE
SOFT BUFFER
HOUSE
2. USAGE RESTRICTION/PRECAUTIONS:
■
To prevent sensor malfunctions, operational failure or any deterioration of its characteristics, do not
use this sensor in the following, or similar conditions.
a) In strong shock or vibration.
b) In high temperature and humidity for a long time.
c) In corrosive gases or sea breeze.
d) In an atmosphere of organic solvents.
e) In dirty and dusty environments that may contaminate the sensor front.
f) Over specified allowable input voltage(Vp-p)
■
Do not solder adding stress on outer lead, also do not apply stress like spin or pressure just after
soldering.
In case you form the leads, support the root firmly.
3. WARRANTY:
■ Period
Warranty period is one year after delivery.
■
Scope
Defective sensors attributable to manufacturer’ responsibility shall be replaced for free during the
warranty period.
However, following cases are out of the scope.
a) Unsuitable handling or misuse by user.
b) Modification or repair by user.
c) Any other cases not due to manufacturer’responsibility such as natural calamity, accident .etc.
This scope covers only replacement.
Any loss derived from failure or malfunction of the sensor, or cost on replacing is excluded from this
warranty scope.
3
FIG4 SIMULATION TEST CIRCUIT
FIG5 DIRECTIVITY TEST
探头
测试插座
桌子
（接测试板）
管
4
TESTING INSTRUMENT AND CONDITION
No.
1
LIST
Testing item
Resonant
Frequency
Testing
Equipment/Methods
Piezoelectric Transducer
Resistance Testing System II
Testing conditions
Testing Environment temperature
Distance to obstacle: 1 meter ,
Obstacle: organic glass board with
20CM*20CM*1.0CM
1.The inductance :
8mH, Q m Value: 60-80, Pulse
：20
2.The Minimum detect distance≥35cm
3.The acoustic system without coupling
The sensor surface is covered by 100mm thickness
of sponge
1.
The inductance :8mH,Qm Value: 60-80, Max Pulse
≤20
2.The Minimum detect distance≥35cm
3.The acoustic system without coupling
In normal room temperature,
the distance to the ground: 55cm
the distance to the obstacle: 50cm
the obstacle: diameter of 50mm PVC pipe,
the obstacle height: 1 meter
Note: there is no other obstacle in a circumference of
1 meter.
Testing temperature :25±2°C
Pulse Width: 0.5mS, Interval :20mS
Normal room temperature
In normal room temperature, according to the Fig. 4
test circuit
In normal room temperature, according to the Fig. 4
test circuit
2
Echo Sensitivity
According to Fig. 4 Test
Circuit
3
Ring Time
According to Fig. 4 Test
Circuit
4
Directivity
(X-axis &Y-axis)
According to Fig. 4 &
Fig. 5 Test Circuit
5
6
7
8
9
Digital LC ZL5
According to Fig. 4 Test
Maximum Input
Circuit
Oscillograph：
Voltage（V p-p)
Fektronix TDS1002
Mean Time to
Aging Equipment
Failure
AWHY001
Operating
High-Low alternating
Temperature(°C) temperature Cabinet
Storage
High-Low alternating
Temperature(°C) temperature Cabinet
Capacitance
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
