®
RAMBUS
Preliminary Information
Direct RDRAM™
256/288-Mbit (512Kx16/18x32s)
Overview
The Rambus Direct RDRAM™ is a general purpose
high-performance memory device suitable for use in a
broad range of applications including computer
memory, graphics, video, and any other application
where high bandwidth and low latency are required.
The 256/288-Mbit Direct Rambus DRAMs (RDRAM
)
are extremely high-speed CMOS DRAMs organized as
16M words by 16 or 18 bits. The use of Rambus
Signaling Level (RSL) technology permits 600MHz to
800MHz transfer rates while using conventional
system and board design technologies. Direct RDRAM
devices are capable of sustained data transfers at 1.25
ns per two bytes (10ns per sixteen bytes).
The architecture of the Direct RDRAMs allows the
highest sustained bandwidth for multiple, simulta-
neous randomly addressed memory transactions. The
separate control and data buses with independent row
and column control yield over 95% bus efficiency. The
Direct RDRAM's 32 banks support up to four simulta-
neous transactions.
System oriented features for mobile, graphics and large
memory systems include power management, byte
masking, and x18 organization. The two data bits in the
x18 organization are general and can be used for addi-
tional storage and bandwidth or for error correction.
Figure 1: Direct RDRAM CSP Package
The 256/288-Mbit Direct RDRAMs are offered in a CSP
horizontal package suitable for desktop as well as low-
profile add-in card and mobile applications.
Key Timing Parameters/Part Numbers
Organization
a
512Kx16x32s
512Kx16x32s
I/O Freq. Core Access Time
MHz
(ns)
600
711
711
800
800
600
711
711
800
800
53
50
45
45
40
53
50
45
45
40
Part
Number
256Ms-53-600
256Ms-50-711
256Ms-45-711
256Ms-45-800
256Ms-40-800
288Ms-53-600
288Ms-50-711
288Ms-45-711
288Ms-45-800
288Ms-40-800
Features
s
Highest sustained bandwidth per DRAM device
- 1.6GB/s sustained data transfer rate
- Separate control and data buses for maximized
efficiency
- Separate row and column control buses for
easy scheduling and highest performance
- 32 banks: four transactions can take place simul-
taneously at full bandwidth data rates
Low latency features
- Write buffer to reduce read latency
- 3 precharge mechanisms for controller flexibility
- Interleaved transactions
Advanced power management:
- Multiple low power states allows flexibility in
power consumption versus time to transition to
active state
- Power-down self-refresh
Organization: 2kbyte pages and 32 banks, x 16/18
- x18 organization allows ECC configurations or
increased storage/bandwidth
- x16 organization for low cost applications
Uses Rambus Signaling Level (RSL) for up to
800MHz operation
512Kx16x32s
512Kx16x32s
512Kx16x32s
512Kx18x32s
512Kx18x32s
512Kx18x32s
512Kx18x32s
512Kx18x32s
s
s
a. The bank designations are described in a later section. Refer
to Section "Row and Column Cycle Description" on page 17.
32s - 32 banks which use a “split” bank architecture
16d - 16 banks which use a “doubled” bank architecture
4i - 4 banks which use an “independent” bank architecture.
Related Documentation
Data sheets for the Rambus memory system components are avail-
able on the Rambus website at http://www.rambus.com. Please
obtain the "Documentation Change History"for this data sheet. The
DCH is an integral part of the data sheet and contains the most
recent information about changes made to the published version.
Check the Rambus website regularly for the latest DCH and data
sheet updates.
s
s
Document DL0060
Version 1.1
Preliminary Information
Page 1
Direct RDRAM™ 256/288-Mbit (512Kx16/18x32s)
Pinouts and Definitions
Center-Bonded Devices - Preliminary
This table shows the pin assignments of the center-
bonded RDRAM package. The mechanical dimensions
10
9
8
7
6
5
4
3
2
1
A
VDD
GND
GND
VDD
GND
GND
VDD
GND
GND
DQA6 DQA4 DQA2 DQA0
SCK
VCMOS
of this package are shown in a later section. Refer to
Section "Center-Bonded uBGA Package (9x8
OPTIONAL)" on page 65.
Table 1: Center Bonded Device (top view)
VDD
GND
VDD
GND
VDD
VDD
VDD
VDD
GND
VDD
GND
VDD
VDD
CMD
VDD
GND
GNDa GNDa
CTM
VDD
CTM
VDD
GND
GND
VDD
COL1
VDD
GND
GND
VCMOS
VDD
GND
VDD
DQA8 DQA7 DQA5 DQA3 DQA1
ROW2 ROW0 COL3
DQB1 DQB3 DQB5 DQB7 DQB8
CFM
GND
CFM
VDDa
ROW1 COL4
VREF
GND
COL2
VDD
COL0
GND
DQB0 DQB2 DQB4 DQB6
GND
VDD
SIO0
SIO1
GND
GND
GND
VDD
GND
VDD
GND
GND
GND
GND
VDD
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
T
U
Note the following:
s
This is the “Top View” (balls facing down, back-
side of chip facing up).
Pin #1 designation is at location A1.
Columns “A” and “U”, and Rows “1” and “10”
can be deleted when die size shrink to the point
that those balls will not fall within the die bound-
aries.
For 32Mx8 devices either DQA8 & DQB8 must be
defined as no connects or columns “B” and “T”
must be deleted completely.
s
s
s
Page 2
Preliminary Information
Document DL0060
Version 1.1
Direct RDRAM™ 256/288-Mbit (512Kx16/18x32s)
Table 2: Pin Description
Signal
SIO1,SIO0
I/O
I/O
Type
CMOS
a
# Pins
edge
2
# Pins
center
2
Description
Serial input/output. Pins for reading from and writing to the control
registers using a serial access protocol. Also used for power man-
agement.
Command input. Pins used in conjunction with SIO0 and SIO1 for
reading from and writing to the control registers. Also used for
power management.
Serial clock input. Clock source used for reading from and writing to
the control registers
Supply voltage for the RDRAM core and interface logic.
Supply voltage for the RDRAM analog circuitry.
Supply voltage for CMOS input/output pins.
Ground reference for RDRAM core and interface.
Ground reference for RDRAM analog circuitry.
Data byte A. Nine pins which carry a byte of read or write data
between the Channel and the RDRAM. DQA8 is not used by
RDRAMs with a x16 organization.
Clock from master. Interface clock used for receiving RSL signals
from the Channel. Positive polarity.
Clock from master. Interface clock used for receiving RSL signals
from the Channel. Negative polarity
Logic threshold reference voltage for RSL signals
Clock to master. Interface clock used for transmitting RSL signals
to the Channel. Negative polarity.
Clock to master. Interface clock used for transmitting RSL signals
to the Channel. Positive polarity.
Row access control. Three pins containing control and address
information for row accesses.
Column access control. Five pins containing control and address
information for column accesses.
Data byte B. Nine pins which carry a byte of read or write data
between the Channel and the RDRAM. DQB8 is not used by
RDRAMs with a x16 organization.
CMD
I
CMOS
a
1
1
SCK
V
DD
V
DDa
V
CMOS
GND
GNDa
DQA8..DQA0
I
CMOS
a
1
14
2
2
19
2
1
6
1
2
9
1
9
I/O
RSL
b
9
CFM
CFMN
V
REF
CTMN
CTM
RQ7..RQ5 or
ROW2..ROW0
RQ4..RQ0 or
COL4..COL0
DQB8..
DQB0
I
I
RSL
b
RSL
b
1
1
1
1
1
1
1
1
3
5
9
I
I
I
I
I/O
RSL
b
RSL
b
RSL
b
RSL
b
RSL
b
1
1
3
5
9
Total pin count per package
74
54
a. All CMOS signals are high-true; a high voltage is a logic one and a low voltage is logic zero.
b. All RSL signals are low-true; a low voltage is a logic one and a high voltage is logic zero.
Document DL0060
Version 1.1
Preliminary Information
Page 3
Direct RDRAM™ 256/288-Mbit (512Kx16/18x32s)
DQB8..DQB0
9
RQ7..RQ5 or
ROW2..ROW0
3
RCLK
1:8 Demux
CTM CTMN
SCK,CMD
2
SIO0,SIO1
2
CFM CFMN
RQ4..RQ0 or
COL4..COL0
5
DQA8..DQA0
9
RCLK
1:8 Demux
TCLK
RCLK
Control Registers
6
REFR
Power Modes
Packet Decode
ROWR
ROWA
11
5
5
9
ROP DR
AV
Match
COLX
5
5
DX
Packet Decode
COLC
5
5
5
7
BX COP DC
S
Match
COLM
8
8
C
MB MA
BR
R
DEVID
XOP
M
BC
Mux
Row Decode
Match
XOP Decode
DM
Write
Buffer
Mux
Mux
PRER
ACT
Sense Amp
64x72
SAmp SAmp SAmp
PREX
Column Decode & Mask
DRAM Core
64x72 512x128x144
0
Bank 0
0/1
64x72
72
SAmp SAmp SAmp
PREC
RD, WR
0
Internal DQB Data Path
72
72
Internal DQA Data Path
0/1
Bank 1
1/2
72
1/2
RCLK
9
9
•••
Bank 2
•••
9
•••
9
RCLK
SAmp SAmp SAmp
14/15 13/14
Bank 13
Bank 14
Bank 15
SAmp SAmp SAmp
13/14 14/15
Write Buffer
Write Buffer
1:8 Demux
1:8 Demux
9
9
15
SAmp SAmp SAmp
15
SAmp SAmp SAmp
16
16
17/18 16/17
Bank 16
Bank 17
Bank 18
•••
16/17 17/18
TCLK
9
9
TCLK
•••
8:1 Mux
•••
8:1 Mux
9
9
SAmp SAmp SAmp
30/31 29/30
Bank 29
Bank 30
Bank 31
SAmp SAmp SAmp
29/30 30/31
31
Figure 2: 256/288-Mbit (512Kx16/18x32s) Direct RDRAM Block Diagram
31
Page 4
Preliminary Information
Document DL0060
Version 1.1
Direct RDRAM™ 256/288-Mbit (512Kx16/18x32s)
General Description
Figure 2 is a block diagram of the 256/288-Mbit Direct
RDRAM. It consists of two major blocks: a “core” block
built from banks and sense amps similar to those
found in other types of DRAM, and a Direct Rambus
interface block which permits an external controller to
access this core at up to 1.6GB/s.
ROW Pins:
The principle use of these three pins is to
manage the transfer of data between the banks and the
sense amps of the RDRAM. These pins are de-multi-
plexed into a 24-bit ROWA (row-activate) or ROWR
(row-operation) packet.
COL Pins:
The principle use of these five pins is to
manage the transfer of data between the DQA/DQB
pins and the sense amps of the RDRAM. These pins are
de-multiplexed into a 23-bit COLC (column-operation)
packet and either a 17-bit COLM (mask) packet or a 17-
bit COLX (extended-operation) packet.
Control Registers:
The CMD, SCK, SIO0, and SIO1
pins appear in the upper center of Figure 2. They are
used to write and read a block of control registers.
These registers supply the RDRAM configuration
information to a controller and they select the oper-
ating modes of the device. The REFR value is used for
tracking the last refreshed row. Most importantly, the
five bit DEVID specifies the device address of the
RDRAM on the Channel.
ACT Command:
An ACT (activate) command from
an ROWA packet causes one of the 512 rows of the
selected bank to be loaded to its associated sense amps
(two 512 bytes sense amps for DQA and two for DQB).
PRER Command:
A PRER (precharge) command
from an ROWR packet causes the selected bank to
release its two associated sense amps, permitting a
different row in that bank to be activated, or permitting
adjacent banks to be activated.
Clocking:
The CTM and CTMN pins (Clock-To-
Master) generate TCLK (Transmit Clock), the internal
clock used to transmit read data. The CFM and CFMN
pins (Clock-From-Master) generate RCLK (Receive
Clock), the internal clock signal used to receive write
data and to receive the ROW and COL pins.
RD Command:
The RD (read) command causes one
of the 128 dualocts of one of the sense amps to be trans-
mitted on the DQA/DQB pins of the Channel.
DQA,DQB Pins:
These 18 pins carry read (Q) and
write (D) data across the Channel. They are multi-
plexed/de-multiplexed from/to two 72-bit data paths
(running at one-eighth the data frequency) inside the
RDRAM.
WR Command:
The WR (write) command causes a
dualoct received from the DQA/DQB data pins of the
Channel to be loaded into the write buffer. There is also
space in the write buffer for the BC bank address and C
column address information. The data in the write
buffer is automatically retired (written with optional
bytemask) to one of the 128 dualocts of one of the sense
amps during a subsequent COP command. A retire can
take place during a RD, WR, or NOCOP to another
device, or during a WR or NOCOP to the same device.
The write buffer will not retire during a RD to the same
device. The write buffer reduces the delay needed for
the internal DQA/DQB data path turn-around.
Banks:
The 32Mbyte core of the RDRAM is divided
into 32 0.5Mbyte banks, each organized as 512 rows,
with each row containing 128 dualocts, and each
dualoct containing 16 bytes. A dualoct is the smallest
unit of data that can be addressed.
Sense Amps:
The RDRAM contains 34 sense amps.
Each sense amp consists of 1kbyte of fast storage (512
bytes for DQA and 512 bytes for DQB) and can hold
one-half of one row of one bank of the RDRAM. The
sense amp may hold any of the 1024 half-rows of an
associated bank. However, each sense amp is shared
between two adjacent banks of the RDRAM (except for
sense amps 0, 15, 16, and 31). This introduces the
restriction that adjacent banks may not be simulta-
neously accessed.
PREC Precharge:
The PREC, RDA and WRA
commands are similar to NOCOP, RD and WR, except
that a precharge operation is performed at the end of
the column operation. These commands provide a
second mechanism for performing precharge.
PREX Precharge:
After a RD command, or after a
WR command with no byte masking (M=0), a COLX
packet may be used to specify an extended operation
(XOP). The most important XOP command is PREX.
This command provides a third mechanism for
performing precharge.
RQ Pins:
These pins carry control and address infor-
mation. They are broken into two groups. RQ7..RQ5
are also called ROW2..ROW0, and are used primarily
for controlling row accesses. RQ4..RQ0 are also called
COL4..COL0, and are used primarily for controlling
column accesses.
Document DL0060
Version 1.1
Preliminary Information
Page 5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
