Edition 2004-04-02
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
81669 München, Germany
©
Infineon Technologies AG 5/7/04.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide
(www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the
failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life
support devices or systems are intended to be implanted in the human body, or to support and/or maintain and
sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other
persons may be endangered.
.
HYB18T256400/800/160AF
DATASHEET Rev. 1.02 (05.04)
Features
•
High Performance:
-5
Speed Sorts
DDR2
-400
-3.7
DDR2
-533
-3S
DDR2
-667
-3
DDR2
-667
256Mb DDR2 SDRAM
Units
tck
MHz
Mb/s/pin
Bin
(CL-tRCD-TRP)
max. Clock
Frequency
Data Rate
CAS Latency (CL)
tRCD
tRP
tRAS
tRC
3-3-3
200
400
3
15
15
40
55
4-4-4
266
533
4
15
15
45
60
5-5-5
4-4-4
333
667
5
15
15
45
60
4
12
12
45
57
tck
ns
ns
ns
ns
• 1.8V ± 0.1V Power Supply
1.8 V ± 0.1V (SSTL_18) compatible) I/O
• DRAM organisations with 4, 8 and 16 data in/outputs
• Double Data Rate architecture: two data transfers per
clock cycle, four internal banks for concurrent operation
• CAS Latency: 3, 4 and 5
• Burst Length: 4 and 8
• Differential clock inputs (CK and CK)
• Bi-directional, differential data strobes (DQS and
DQS) are transmitted / received with data. Edge
aligned with
read data and center-aligned with write data
• DLL aligns DQ and DQS transitions with clock
• DQS can be disabled for single-ended data strobe
operation
• Commands entered on each positive clock edge, data
and data mask are referenced to both edges of DQS
• Data masks (DM) for write data
• Posted CAS by programmable additive latency for
better command and data bus efficiency
• Off-Chip-Driver impedance adjustment (OCD) and
On-Die-Termination (ODT) for better signal quality.
• Auto-Precharge operation for read and write bursts
• Auto-Refresh, Self-Refresh and power saving Power-
Down modes
• Average Refresh Period 7.8µs at a T
CASE
lower than
85
o
C, 3.9µs between 85
o
C and 95
o
C
• Normal and Weak Strength Data-Output Drivers
• 1k page size
• Lead-freePackages:
60 pin FBGA for x4 & x8 components
84 pin FBPA for x16 components
1.0 Description
The 256Mb Double-Data-Rate-2 (DDR2) DRAMs are high-
speed CMOS Double Data Rate 2 Synchronous DRAM
devices containing
268,435,456
bits and are internally config-
ured as a quad-bank DRAMs. The 256Mb chip is organized
as either 16Mbit x 4 I/O x 4 bank, 8Mbit x 8 I/O x 4 bank or
4Mbit x 16 I/O x 4 bank device. These synchronous devices
achieve high speed double-data-rate transfer rates of up to
667 Mb/sec/pin for general applications.
The chip is designed to comply with all key DDR2 DRAM key
features: (1) posted CAS with additive latency, (2) write
latency = read latency -1, (3) normal and weak strength data-
output driver, (4) Off-Chip Driver (OCD) impedance adjust-
ment and (5) an ODT (On-Die Termination) function.
All of the control and address inputs are synchronized with
a pair of externally supplied differential clocks. Inputs are
latched at the cross point of differential clocks (CK rising
and CK falling). All I/Os are synchronized with a single
ended DQS or differential (DQS, DQS) pair in a source
synchronous fashion. A 15 bit address bus is used to con-
vey row, column and bank address information in a RAS /
CAS multiplexing style.
The DDR2 devices operate with a 1.8V +/-0.1V power
supply and are available in FBGA packages.
An Auto-Refresh and Self-Refresh mode is provided along
with various power-saving power-down modes.
The functionality described and the timing specifications
included in this data sheet are for the DLL Enabled mode
of operation.
Page 3
Rainer.Weidlich@Infineon.com
Rev. 1.02
May 2004
INFINEON Technologies
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
