First Edition
Mar 10, 2006
LCD Module Technical Specification
T-51944D104J-FW-A-ABN
Final Revision
******
Type No.
Approved by (Quality Assurance Division)
Checked by (ACI Engineering Division)
S.Sano
Prepared by (ACI Engineering Division)
No.
--
1
2
3
4
5
6
7
8
9
10
11
12
13
--
--
--
CONTENTS
APPLICATION
OVERVIEW
Item
Page
1
2
3
4
4
7
9
14
15
17
20
21
22
23
26
29
31
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
INTERFACE PIN CONNECTION
INTERFACE TIMING
BLOCK DIAGRAM
MECHANICAL SPECIFICATION
OPTICAL CHARACTERISTICS
RELIABILITY TEST CONDITION
INSPECTION STANDARDS
OTHER FEATURE
HANDLING PRECAUTIONS FOR TFT-LCD MODULE
PACKAGING SPECIFICATION
PRODUCTS NUMBER LABLING FORMS
LAMP UNIT for 10.4” SVGA
T-51944D104J-FW-A-ABN (AB) No. 2006-0048
OPTREX CORPORATION
Page 1/36
1. APPLICATION
This specification applies to color TFT-LCD module, T-51944D104J-FW-A-ABN.
These specification papers are the proprietary product of OPTREX and include materials protected
under copyright of OPTREX. No part of this document may be reproduced in any form or by any
means without the express written permission of OPTREX.
OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a product specified in this document. No
license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual
property rights of OPTREX or of others.
OPTREX classifies the usage of the TFT-LCD module as follows. Please confirm the usage before
using the product.
(1) Standard Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
(2) Special Usage
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
(3) Specific Usage
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control
systems, life support systems and any other equipment. OPTREX should make a contract
that stipulate apportionment of responsibilities between OPTREX and our customer.
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should contact OPTREX sales representative in advance.
OPTREX has been making continuous effort to improve the reliability of its products. Customers
should implement sufficient reliability design of their application equipments such as redundant
system design, fail-safe functions, anti-failure features.
OPTREX assumes no responsibility for any damage resulting from the use of the product that does
not comply with the instructions and the precautions specified in this document.
Please contact and consult a OPTREX sales representative for any questions regarding this product.
T-51944D104J-FW-A-ABN (AB) No. 2006-0048
OPTREX CORPORATION
Page 2/36
2. OVERVIEW
T-51944D104J-FW-A-ABN is 10.4” color TFT-LCD (Thin Film Transistor Liquid Crystal Display)
module composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 800
×
600, 262K-color or 16.7M-color images are displayed on
the 10.4” diagonal screen. Input power voltage is 3.3 V for LCD driving.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 40
MHz clock cycle.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM
Display Area (mm)
Number of Dots
Pixel Pitch (mm)
Color Pixel Arrangement
Display Mode
Number of Color
Luminance (cd/m
2
)
Wide Viewing Angle Technology
Viewing Angle (CR
≥
10)
Surface Treatment
Electrical Interface
Optimum Viewing Angle (Contrast ratio)
Module Size (mm)
Module Mass (g)
Backlight Unit
SPECIFICATION
211.2
×
158.4
(10.39-inch diagonal)
800
×
3 (H)
×
600 (V)
0.264 (H)
×
0.264 (V)
RGB vertical stripe
Normally white TN
262K(6 bit/color), 16.7M(8 bit/color)
400
Optical Compensation Film
-65~65° (H)
-60~50° (V)
Antireflection and hard-coating 2H
LVDS(6 bit/8 bit)
6 o’clock
243.0 (W)
×
181.6 (H)
×
12.2 (D)
570
CCFL, 2-tubes, edge-light, replaceable
Characteristic value without any note is typical value.
T-51944D104J-FW-A-ABN (AB) No. 2006-0048
OPTREX CORPORATION
Page 3/36
3. ABSOLUTE MAXIMUM RATINGS
ITEM
Power Supply Voltage for LCD
Logic Input Voltage
Lamp Voltage
Lamp Current
Lamp Frequency
Operation Temperature (Panel)
Operation Temperature (Ambient)
Storage Temperature
Note 1,2)
Note 2)
Note 2)
SYMBOL
VCC
VI
VL
IL
FL
T
op(Panel)
T
op(Ambient)
T
stg
MIN.
0
−0.3
0
0
40
−20
−20
−20
MAX.
4.0
VCC+0.3
2000
9
100
70
70
80
UNIT
V
V
Vrms
mArms
kHz
°C
°C
°C
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg
≤
40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than the value of 90%RH at 40°C without
condensation.
4. ELECTRICAL CHARACTERISTICS
(1) TFT-LCD
Ambient temperature: Ta = 25℃
ITEM
Power Supply Voltage for LCD
Power Supply Current for LCD
Permissive Input Ripple Voltage
*1) Power and signals sequence:
t1
≤
10 ms
0 < t2
≤
50 ms
0 < t3
≤
50 ms
SYMBOL
VCC
ICC
VRP
200 ms
≤
t4
200 ms
≤
t5
0
≤
t6
VCC
0.9VCC
LCD Power Supply
Logic Signal
MIN.
3.0
--
--
TYP.
3.3
315
--
MAX.
3.6
430
100
UNIT
V
mA
mVp-p
Remarks
*1)
*2)
VCC = +3.3V
0.9VCC
data
0.1VCC
0.1VCC
0.1VCC
t1
t2
VL
t3
t4
Backlight Power Supply
t5
t6
data: RGB DATA, DCLK, DENA
T-51944D104J-FW-A-ABN (AB) No. 2006-0048
OPTREX CORPORATION
Page 4/36
VCC-dip conditions:
1) When 2.6 V
≤
VCC < 3.0 V, td
≤
10 ms
2) When VCC < 2.6 V
VCC-dip conditions should also follow the power and signals sequence.
VCC
td
*2) Typical current condition:
64-gray-bar pattern(6 bit)
256-gray-bar pattern(8 bit)
600 line mode
VCC = +3.3 V , f
H
=37.9 kHz, f
V
=60 Hz, f
CLK
= 40 MHz
(2) Backlight
Ta = 25℃
ITEM
Lamp Voltage
Lamp Current
Lamp Frequency
Starting Lamp Voltage
SYMBOL
MIN.
--
3.0
40
900
1350
1440
TYP.
470
6.5
--
--
--
--
--
2.6 V
MAX.
--
7.5
100
--
--
--
--
3.0 V
UNIT
Vrms
mArms
kHz
Vrms
Vrms
Vrms
h
Remarks
IL = 6.5 mArms
*1),*5)
*2)
Ta = 25°C
Ta = 0°C
Ta =
−20°C
*3),*4) IL = 6.5 mArms,
Continuous operation
VL
IL
FL
VS
Lamp Life Time
LT
50,000
*1) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL
CTH
A
LCD
Module
CTL
CTH
A
Inverter
Power
Supply
*2) Lamp frequency of inverter may produce interference with horizontal synchronous frequency,
and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and
keep inverter as far from module as possible or use electronic shielding between inverter and
module to avoid the interference.
*3) Lamp life time is defined as the time either when the brightness becomes 50% of the initial value,
or when the starting lamp voltage does not meet the value specified in this table.
*4) The life time of the backlight depends on the ambient temperature. The life time will decrease
under low/high temperature.
T-51944D104J-FW-A-ABN (AB) No. 2006-0048
OPTREX CORPORATION
Page 5/36
能源基础设施
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
