Interface Connectors for Factory Automation Network
HR31 Series
Complies with DeviceNet requirements
Comparison of plug heights
●Hirose
HR31
Dec.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
●Other
manufacturer’s product
15
■
Features
1. DeviceNet Compliant
Conforms to requirements of Factory Automation Network DeviceNet standards.
Hirose products are distinct from products of made others, as described below.
Feature
Made by others
Hirose HR31
Crimped and connected to terminal then
fastened simply by inserting into housing.
Plug height is 10.2 mm, allowing use of less
space when mounting several connectors
Permanently identified contact positions
No need for screws, built-in locking pin secures
connector to the board
Crimped to commercially available cap
Reduced number of termination
connectors, inserted into housing and
operations
fastened by screw. (*)
High density mounting
Prevention of connection errors
Number of required operations
to secure receptacle assembly
to the board
Plug height : 15 mm
Contact positions not identified.
Connectors are attached by screws from
the opposite side.
*Although it is possible to terminate discrete cables with screws and not use a pin contact, however, there is the potential issue
and concern for long-term reliability and problems. Therefore, most users prefer to use crimp contacts.
2. Screw-lock style
The screw lock style connector features secure mating and
a higher locking force retention.
Total space occupied by mated
assemblies
3. Snap-lock Style
The snap lock plug features a structure that creates a tactile
click during mating.
With screw lock
12
20
4. Commercially available tools may be used
35.5
Use crimp tools conforming to JIS C 9711 standards.
Terminated contacts can be removed using 1 mm dia. steel
pin. and re-inserted.
3 4
5
5. Protected contacts
10.2
When installed, the crimped contacts are protected
completely by the plug housing. This design eliminates the
risk of damaging the contacts.
1 2
27
10.2
2014.12w
1
HR31 Series●Interface Connectors for Factory Automation Network
Product Specification
Rating
Current rating
Voltage rating
12A (2.5mm
2
wire)
10A (1.5mm
2
wire)
250V AC, 350V DC
Operating temperature range
Storage temperature range
-40ç to +100ç
-40ç to +85ç
Item
1.Contact resistance
2.Insulation resistance
3.Withstanding voltage
Specification
5 mø max.
1000 Mø min.
No flashover or insulation breakdown
Conditions
1A DC
500 V DC
2000V AC/one minute
Standard waveform of 4KV, positive/negative,
3 times each
Frequency: 10 to 55 Hz, single amplitude of
0.75 mm, 5 min. in each of the 3 directions, 10
cycles each
1000 cycles
Temperature: -40ç / Room temperature to
+100ç / Room temperature
Time: 30 / 10 to 15 / 30 / 10 to 15 (Minutes)
5 cycles
96 hours at temperature of 40ç and humidity
of 90% to 95%
4.Impulse withstanding voltage No flashover or insulation breakdown
5.Vibration
No electrical discontinuity of 10 µs or more
Contact resistance: 10 mø max.
Dec.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
6.Durability
(insertion/ withdrawal)
7.Temperature cycle
Insulation resistance: 1000 Mø min.
Insulation resistance:
10 Mø min. (Humidity state)
100 Mø min. (Dry state)
8.Humidity
Materials
Plug
Crimp contact
Part
Insulator
Screw
Socket contact
Insulator
Receptacle
Male contact
Nut
Board retention pin
Material
PBT
Steel
Contact area: phosphor bronze
Termination area: copper
PBT
Brass
Steel
Phosphor bronze
Finish
Color: Black or Green
Nickel plating
Contact area: gold plating
Termination area: tin plating
Color: Black or Green
Contact area: gold plating
Termination are: gold plating
Nickel plating
Tin plating
Remarks
UL94V-0
–––––
–––––
UL94V-0
–––––
–––––
Board retention pin
Ordering information
●Connector
HR31 - 5.08 P A - 5 S C (01)
q
w
e
r
t
y
u
i
u
Terminal type
C: Crimping
DL: Right angle through hole type
D: Straight through hole type
i
Other specifications: A two-digit number
such as (01) or (02) is
added to indicate
other specifications.
q
Model name
w
Contact pitch
e
Connector type
HR31
5.08mm
P: Plug
R: Receptacle
Blank: With screw
r
Screw lock type
A: Without screw
5
t
Number of contacts
y
Contact type
S: Female contact
P: Male contact
●Crimp
contact
HR31 - SC - 1 1 1 (01)
!0
!1 !2 !3
o
!4
HR31
o
Model name
!3
Plating type
1: Gold plating
!0
Contact type
SC: female contact
!1
Contact packaging type 1: loose contact
!4
Other specifications: A two-digit number
!2
Conductor cross area
such as (01) or (02) is
2
added to indicate
1: 1.04 to 2.63mm
2
other specifications.
2: 0.2 to 1.65mm
2
HR31 Series●Interface Connectors for Factory Automation Network
Plug (with screw lock)
27
25.4
35.5
Dec.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
HR31-5.08P-5SC
Part No.
HR31-5.08P-5SC(72)
HRS No.
131-0002-2 72
Weight
8g
B
Color
Green
Crimp contact
2.35
23
B
Part No.
HR31-SC-111(71)
HR31-SC-121(71)
HRS No.
131-0004-8 71
131-0005-0 71
ØA
4
3.3
Weight
1g
Contact plating Applicable conductor cross area (Note 2)
2
1.04 to 2.63mm
Gold
2
0.2 to 1.65mm
Note 1: Packaging (100 pcs/pack)
Note 2: For a multi-strand conductors
Receptacle (Right angle through hole type with screw lock)
ØA
35.5
8.6
1
2
3
4
5
10.2
8.3
B-B
Connector mounting side
12
28.3
7.5
10
HR31-5.08R-5PDL
Part No.
HR31-5.08R-5PDL(72)
HR31-5.08R-5PDL(75)
HRS No.
131-0001-0 72
131-0001-0 75
Weight
4g
Color
Black
Green
Contact plating
Gold
Board retention pin
With
PCB mounting pattern
●
With screw lock
7.5±0.05
1.6
5-Ø
+0.1
0
h
roug
(Th
hole
)
+0.1
0
10 ±0.05
2-Ø
2.3
(Thr
oug
le)
h ho
5.08±0.05
10.16±0.05
15.24±0.05
15.24±0.05
5.08±0.05
10.16±0.05
Connector mounting side
(Board thickness =1.6)
3.3
3
1 2 3 4 5
3
HR31 Series●Interface Connectors for Factory Automation Network
Receptacle (Straight through hole type with screw lock)
35.5
8.6
１
２
３
４
５
12
4.3
Dec.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
HR31-5.08R-5PD
Part No.
HR31-5.08R-5PD(76)
HRS No.
131-0003-5 76
Weight
4g
Color
Green
Connector mounting side B
Contact plating
Gold
Board retention pin
Without
PCB mounting pattern
●
With screw lock
r
Th
ou
g
o
hh
le)
Ø
5-
1.6
.1
+0
0
(
3.8±0.05
5.08±0.05
10.16±0.05
5.08±0.05
10.16±0.05
Connector mounting side B
(Board thickness =1.6)
3.8
4
HR31 Series●Interface Connectors for Factory Automation Network
Tools
Type
Part No.
HRS No.
Manual crimp tool
Contact removal pin
HR31-TC-01
HR31-SC-TP
902-1512-4
150-0215-1
Dec.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Manual crimp tool
Contact removal pin
●
Tools application procedures
1. Manual contact crimp tool
The tool will terminate all specified crimp contacts. Placement of correct contact in
corresponding crimp position on the tool is critical. The positions are clearly indicated on the tool
as (2) and (1.25). The exposed conductor strip length is 5mm.
Crimp position indicator
Applicable crimp contact
2
1.25
HR31-SC-111
HR31-SC-121
Crimp position indicator
1.25
2. Contact removal/extraction
Wiring errors can be corrected by removing the crimp contacts using the extraction tool and the
following procedure.
1) Insert the extraction tool from the underside of connector and apply pressure onto the mold
lance. (Fig.1)
2) While pressing on the mold lance, angle the extraction tool and release the disconnection
prevention mechanism on the crimping contact. (Fig.2)
3) Remove the extraction tool.
4) Pull the wire rearward to disconnect and remove the contact.
2
Mold lance
Wire
Mold lance
Wire
Pull-out
Contact removal pin
Insertion direction
Contact removal pin
5
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
