Reference Only
Product Specification for Reference Only
Issued Date:
Rev.:
April 30, 2015
N
Part Description:
MURATA Part No.:
Ultrasonic Transducer
MA40S4S
The product specification in this sheet is for reference only. The contents of this specification are
subject to change.
You are requested to receive the latest specification and to return one copy of the specification to
us with your receipt signature before going into mass production.
Sensor products department 1
Sensor products division
Murata Manufacturing Co., Ltd.
Reference Only
P1/5
Specification of Ultrasonic Transducer
Type: MA40S4S
1. Scope
This product specification is applied to the Transmitter of Ultrasonic Transducer
(Open Type Structure).
2. Customer Part Number
3. Murata Part Number
MA40S4S
4. Structure
Dimension : As per Fig.1
5. Absolute Maximum Ratings
Items
5-1 Operating temperature range
5-2 Storage temperature range
5-3 Max. Input Voltage
Specification
-40 to +85 degC
-40 to +85 degC
20 Vp-p
Note
-
-
at 40kHz, Square continuous wave
6. Specifications
(* Temperature 25 ± 3 degC, 45 to 75 %R.H, unless otherwise noted)
Items
6-1 Operating Frequency
Specification
40.0 kHz
For reference
at 40 kHz,10 Vrms, Sine wave,30 cm
0 dB = 2x10
-5
Pa
(per measuring circuit Fig.2)
at 1 kHz
at 50 V D.C.
-40 to +85 degC
Note
6-2 SPL (Sound Pressure Level) 120 +/- 3 dB
6-3 Capacitance
6-4 Insulation Resistance
6-5 Temperature Characteristics
2,550 pF +/- 20 %
More than 100 Mohm
Within +/- 3dB against initial
value at 25 degC
MURATA MANUFACTURING Co., LTD.
Rev.N
Reference Only
P2/5
7. Environmental tests
(Standard Test Condition: 25 +/- 3 degC, 45 to 75 %R.H)
7.1 Shock Test
The variation of the sound pressure level at 40
25 degC after applied following test conditions
Acceleration
:
Direction
:
Shock time
:
7.2 Vibration Test
The variation of the sound pressure level at 40
25 degC after applied following test conditions
Vibration frequency
:
Sweep Period
:
Amplitude
:
Directions
:
Time
:
kHz is within +/-3 dB compared with initial stage at
sine 980 m/s
2
(100 G), 6 ms
3 directions
3 times / directions
kHz is within +/-3 dB compared with initial stage at
10 to 55 Hz
1 min.
1.5 mm
3 directions
2 hours / direction
7.3 Resistance to Soldering Heat
The variation of the sound pressure level at 40 kHz is within +/-3 dB compared with Initial stage at
25 degC in 1hour after touching soldering iron (Iron temperature : 350 degC), 3 seconds with the
terminal. (Touching point must be 2mm or more away from the transducer body.)
7.4 High Temperature Test
The variation of the sound pressure level at 40 kHz is within +/-3 dB compared with initial stage at
25 degC in 24 hours after applied following test conditions
Temperature
:
+85 +/-2 degC
Time
:
100 hours
7.5 Low Temperature Test
The variation of the sound pressure level at 40 kHz is within +/-3 dB compared with initial stage at
25 degC in 24 hours after applied following test conditions
Temperature
:
-40 +/- 2 degC
Time
:
100 hours
7.6 Humidity Test
The variation of the sound pressure level at 40 kHz is within +/-3 dB compared with initial stage at
25 degC in 24 hours after following test conditions
Temperature
:
+60 +/-2 degC
Humidity
:
90 to 95 %R.H.
Time
:
100 hours
7.7 Operating Test
The variation of the sound pressure level at 40 kHz is within +/-6 dB compared with initial figures at
25 degC in 24 hours after following test conditions
Input voltage
:
24Vp-p at Square wave, 40 kHz
Continuous signal
Time
:
1000 hour
7.8 Pull Strength
There should be no substantial damage until 9.8 N of pulling force.
MURATA MANUFACTURING Co., LTD.
Rev.N
Reference Only
P3/5
8.
Caution
8-1 Limitation of Applications
Please do not use in the applications listed below which require a high reliability to prevent the
defects which might cause a damage to the Peoples’ life and/or property.
1)
Aircraft equipment
2)
Aerospace equipment
3)
Undersea equipment
4)
Power plant control equipment
5)
Medical equipment
6)
Transportation equipment (trains, ships, etc.)
7)
Traffic signal equipment
8)
Disaster prevention / crime prevention equipment
9)
Data-processing equipment
10)
Military equipment (regardless of directly/indirectly)
11)
Security device/system
12)
Outside-usage, in which the transducer is exposed to splashes or dusts
13)
Application of similar complexity and/or reliability requirement to the applications listed in
the above
8-2 Fail-safe
Please make sure to provide an appropriate fail-safe function on your product to prevent a second d
amage that may be caused by the abnormal function or the failure of our product.
9. Caution in use
9-1 (Notice in design and usage)
1)
The transducer may generate surge voltage by mechanical or thermal shock.
2)
Please do not apply D.C. voltage for ultrasonic transducer to avoid migration.
3)
Please do not use this ultrasonic transducer in water.
4)
Please do not apply an excessive mechanical shock or force on the top of this ultrasonic
transducer and terminal pins. It may cause of disconnection and malfunction.
5)
Please do not use nor storage this ultrasonic transducer in heavy dust condition. It may be
a cause of clogging and low performance. Also, please do not use this transducer in high
humidity or high concentrated exhaust gas. It may be a cause of corrosion and
malfunction.
6)
Care should be taken when select the material to hold, or cover backside of transducer. If
it contains sulfur or sulfide, electrode on piezo-electric element may be corroded and
became malfunction.
7)
This transducer does not have a definition of terminal polarity. Please check a signal
before using if you need a signal phase control for your application.
9-2 (Notice in storage)
1)
The products should not be used or stored in a corrosive atmosphere, especially where
chloride gas, sulfide gas, acid, alkali, salt or the like are present. Store the products in the
room where is normal temperature and humidity, and avoid the sunlight, sudden changes
in temperature and humidity. It may cause of failure or malfunction in such conditions.
2)
Store the products where the temperature and relative humidity do not exceed -10 to 40
degC, and 30 to 80 %RH. Use the products within 6 months after receiving.
9-3 (Notice in mounting)
1)
Please do not apply excessive force to terminals, when soldering.
2)
Please use soldering temperature with not exceeds 350 degC, 3 seconds.
3)
Flow soldering is not applicable.
4)
Please do not clean by water and dissolving agent.
5)
This product cannot be used mounted on PCB. Soldering fillet at the bottom of case may
interfere with throughhole of PCB. Please contact products engineering section of Murata if
you will use this product mounted on PCB.
MURATA MANUFACTURING Co., LTD.
Rev.N
Reference Only
P4/5
10.
Note
1)
2)
3)
Please make sure that your product has been evaluated in view of your specifications
with our product being mounted to your product.
You are requested not to use our product deviating from the agreed specifications.
We consider inappropriate to include any terms or conditions with regard to the business
transaction in the product specifications, drawings or other technical documents.
Therefore, if your technical documents as above include such terms and conditions such
as warranty clause, product liability clause, or intellectual property infringement liability
clause, they will be deemed to be invalid.
Dimensions
(2.0)
7.1 ± 0.3
Dia. 9.9 ± 0.3
2-
0.64± 0.1
10.0 ± 1.0
Caution)
There is a fillet of solder in this area.
Please refer to 9-3 (Notice in mounting)
Prohibited area of customer
soldering
() : Reference value
Unit: mm.
5.0 ± 0.3
Lot No. 6 digits
X X XXXX
xxxxxx
S
Year (1 digit)
Month (1 digit)
Serial Number (4 digits)
Run number is reset
every month.
0~9 (cycle 10 years) Jan.~Sep. → 1 ~ 9 0001~9999
Ex.. 2013 → 3 Oct. → X
2014 → 4
2015 → 5
2016 → 6
Nov. → Y
Dec. → Z
Fig.1: Product Dimension
MURATA MANUFACTURING Co., LTD.
Rev.N
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
