Datasheet> 器件分类 > 无源元件> 电容器> PLG0E222MDO1TD

PLG0E222MDO1TD: 产品描述Aluminum Electrolytic Capacitor, Polarized, Aluminum, 2.5V, 20% +Tol, 20% -Tol, 2200uF; 产品类别无源元件电容器; 文件大小512KB，共2页; 制造商Nichicon(尼吉康); 官网地址http://www.nichicon.co.jp; 标准

下载文档详细参数选型对比全文预览

PLG0E222MDO1TD在线购买

供应商	器件名称	价格	最低购买	库存
	PLG0E222MDO1TD	-	-	点击查看	点击购买

PLG0E222MDO1TD概述

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 2.5V, 20% +Tol, 20% -Tol, 2200uF

PLG0E222MDO1TD规格参数

参数名称	属性值
是否无铅	不含铅
是否Rohs认证	符合
Objectid	763881121
包装说明	,
Reach Compliance Code	compliant
Country Of Origin	Japan
ECCN代码	EAR99
Samacsys Manufacturer	Nichicon
Samacsys Modified On	2023-01-21 20:03:25
YTEOL	6.65
电容	2200 µF
电容器类型	ALUMINUM ELECTROLYTIC CAPACITOR
直径	8 mm
介电材料	ALUMINUM (WET)
ESR	8 mΩ
长度	12 mm
负容差	20%
端子数量	2
最高工作温度	105 °C
最低工作温度	-55 °C
封装形式	Radial
包装方法	Tape
极性	POLARIZED
正容差	20%
额定（直流）电压（URdc）	2.5 V
纹波电流	6700 mA
端子节距	3.5 mm

文档预览

下载PDF文档

全文
预览

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

PLG

Specifications

Item

Category Temperature Range

Rated Voltage Range

Radial Lead Type, Higher Capacitance

Higher Capacitance, Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

Radial lead type :

Lead free flow soldering condition correspondence

Compliant to the RoHS directive (2011/65/EU).

PLG

Higher

Capacitance

PLF

Performance Characteristics

– 55 to +105°C

2.5 to 16V

330 to 3900µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Rated Capacitance Range

Capacitance Tolerance

ESR (

Tangent of loss angle (tan

δ)

Less than or equal to the specified value at 120Hz, 20°C

Leakage Current (

Less than or equal to the specified value.

Z+105°C / Z+20°C

Z– 55°C / Z+20°C

1.25

(100kHz)

After 2 minutes' application of rated voltage at 20°C

Temperature Characteristics

(Max.Impedance Ratio)

Endurance

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 105°C.

Capacitance change

tan

ESR

( 1)

Leakage current ( 2)

Capacitance change

tan

ESR

( 1)

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

Less than or equal to the initial specified value

Damp Heat

(Steady State)

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

Resistance to

Soldering Heat

After soldering the capacitor under the soldering conditions prescribed

here as preheat at 150 to 200°C for 60 to 180 seconds and peak

temperature at 265°C for 10 seconds or less, the capacitor shall meet

the specifications listed at right, provided that its temperature profile is

measured at both of terminal ends facing the soldering side.

Navy blue print on the case top

Capacitance change

tan

ESR

( 1)

Leakage current ( 2)

Marking

1 ESR should be measured at both of the terminal ends closest to the capacitor body.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

Dimensions

Capacitance

Type numbering system (Example : 4V 1200µF)

Resin coated Case

9 10 11 12

Voltage(g:4V)

P L G 0 G 1 2 2 MCO 1

φD±0.5

1200

841

P ±0.5

Size code

Configuration

Series

Lot. No.

L+0.5MAX.

15MIN

4MIN

Capacitance tolerance (±20%)

Rated capacitance (1200µF)

Rated voltage (4V)

Series name

Size

φD

φd

φ8

8.0

8.5

3.5

0.6

(mm)

φ8

12L

φ10

13L

8.0

10.0

11.5

3.5

0.6

12.5

5.0

0.6

Type

Voltage

Code

2.5

6.3

Frequency coefficient of rated ripple current

Frequency0/ 120Hz

Coefficient

0.05

1kHz

0.30

10kHz 100kHz or more

0.70

1.00

Please refer to page 20 about the end seal configuration.

Dimension table in next page.

PLG0E222MDO1TD相似产品对比

	PLG0E222MDO1TD	PLG0E272MDO1TD	PLG1C471MDO1	PLG0E392MDO1TD	PLG0J122MDO1
描述	Aluminum Electrolytic Capacitor, Polarized, Aluminum, 2.5V, 20% +Tol, 20% -Tol, 2200uF	Aluminum Electrolytic Capacitor, Polarized, Aluminum, 2.5V, 20% +Tol, 20% -Tol, 2700uF	Multilayer Ceramic Capacitors MLCC - SMD/SMT 100uF 16V X5R +/-20% 1210 HiCV	Aluminum Electrolytic Capacitor, Polarized, Aluminum, 2.5V, 20% +Tol, 20% -Tol, 3900uF	Phone Connectors 3.5MM STEREO JACK
ESR	8 mΩ	8 mΩ	11 mOhms	8 mΩ	9 mOhms
是否无铅	不含铅	不含铅	-	不含铅	-
是否Rohs认证	符合	符合	-	符合	-
Objectid	763881121	763881130	-	763881139	-
Reach Compliance Code	compliant	compliant	-	compliant	-
Country Of Origin	Japan	Japan	-	Japan	-
ECCN代码	EAR99	EAR99	-	EAR99	-
YTEOL	6.65	6.98	-	6.65	-
电容	2200 µF	2700 µF	-	3900 µF	-
电容器类型	ALUMINUM ELECTROLYTIC CAPACITOR	ALUMINUM ELECTROLYTIC CAPACITOR	-	ALUMINUM ELECTROLYTIC CAPACITOR	-
直径	8 mm	10 mm	-	10 mm	-
介电材料	ALUMINUM (WET)	ALUMINUM	-	ALUMINUM (WET)	-
长度	12 mm	13 mm	-	13 mm	-
负容差	20%	20%	-	20%	-
端子数量	2	2	-	2	-
最高工作温度	105 °C	105 °C	-	105 °C	-
最低工作温度	-55 °C	-55 °C	-	-55 °C	-
封装形式	Radial	Radial	-	Radial	-
包装方法	Tape	Tape	-	Tape	-
极性	POLARIZED	POLARIZED	-	POLARIZED	-
正容差	20%	20%	-	20%	-
额定（直流）电压（URdc）	2.5 V	2.5 V	-	2.5 V	-
纹波电流	6700 mA	5560 mA	-	7000 mA	-
端子节距	3.5 mm	5 mm	-	5 mm	-

PLG0E222MDO1TD

PLG0E222MDO1TD在线购买

PLG0E222MDO1TD概述

PLG0E222MDO1TD规格参数

文档预览

PLG0E222MDO1TD相似产品对比

推荐资源