FMS2027
DC–20 GH
Z
MMIC SPDT N
ON
-R
EFLECTIVE
S
WITCH
F
EATURES
:
•
•
•
•
•
Available in die form
Non-Reflective design
Low Insertion loss 2.2 dB at 20GHz typical
Very high isolation 40 dB at 20GHz typical
Excellent low control voltage performance
Preliminary Datasheet v2.2
F
UNCTIONAL
S
CHEMATIC
:
RFIN
G
ENERAL
D
ESCRIPTION
:
The FMS2027 is a low loss high isolation
broadband single pole single throw Gallium
Arsenide switch designed for use in broadband
communications instrumentation and electronic
warfare applications. The die is fabricated
using the Filtronic FL05 0.5µm switch process
technology
that
offers
leading
edge
performance optimised for switch applications.
RFO1
RFO2
T
YPICAL
A
PPLICATIONS
:
•
•
•
Broadband communications
Instrumentation
Electronic warfare (ECM, ESM)
E
LECTRICAL
S
PECIFICATIONS
(based on on-wafer measurements):
P
ARAMETER
Insertion Loss
Insertion Loss
Insertion Loss
Isolation
Isolation
Isolation
Return Loss (on state)
Return Loss (of state)
Switching speed
P1dB
C
ONDITIONS
(DC-10) GHz, Small Signal
(10-15) GHz, Small Signal
(15-20) GHz, Small Signal
(DC-10) GHz, Small Signal
(10-15) GHz, Small Signal
(15-20) GHz, Small Signal
(DC-20) GHz, Small Signal
(DC-20) GHz, Small Signal
50% control to 10% / 90% RF
-5V control
M
IN
T
YP
1.4
1.7
2.2
40
35
40
14
25
10
25
M
AX
U
NITS
dB
dB
dB
dB
dB
dB
dB
dB
ns
dBm
Note: T
AMBIENT
= 25°C, Vctrl = 0V/-5V, Z
IN
= Z
OUT
= 50Ω
1
Specifications subject to change without notice
Filtronic Compound Semiconductors Ltd
Fax: +44 (0) 1325 306177
Email: sales@filcs.com
Tel: +44 (0) 1325 301111
Website:
www.filtronic.com
FMS2027
Preliminary Datasheet v2.2
P
REFERRED
A
SSEMBLY
I
NSTRUCTIONS
:
GaAs devices are fragile and should be
handled with great care. Specially designed
collets should be used where possible.
The back of the die is metallised and the
recommended mounting method is by the use
of solder or conductive epoxy. If epoxy is
selected then it should be applied to the
attachment surface uniformly and sparingly to
avoid encroachment of epoxy on to the top
face of the die and ideally should not exceed
half the chip height. For automated dispense
Ablestick LMISR4 is recommended and for
manual dispense Ablestick 84-1 LMI or 84-1
LMIT are recommended. These should be
cured at a temperature of 150°C for 1 hour in
an oven especially set aside for epoxy curing
only. If possible the curing oven should be
flushed with dry nitrogen.
This part has gold (Au) bond pads requiring
the use of gold (99.99% pure) bondwire. It is
recommended that 25.4µm diameter gold wire
be used. Thermosonic ball bonding is
preferred. A nominal stage temperature of
150°C and a bonding force of 40g has been
shown to give effective results for 25µm wire.
Ultrasonic energy shall be kept to a minimum.
For this bonding technique, stage temperature
should not be raised above 200°C and bond
force should not be raised above 60g.
Thermosonic
wedge
bonding
and
thermocompression wedge bonding can also
be used to achieve good wire bonds.
Bonds should be made from the die first and
then to the mounting substrate or package.
The physical length of the bondwires should be
minimised especially when making RF or
ground connections.
H
ANDLING
P
RECAUTIONS
:
To avoid damage to the devices care should
be exercised during handling.
Proper
Electrostatic Discharge (ESD) precautions
should be observed at all stages of storage,
handling, assembly, and testing.
These
devices should be treated as Class 1A (0-500
V) as defined in JEDEC Standard No. 22-
A114. Further information on ESD control
measures can be found in MIL-STD-1686 and
MIL-HDBK-263.
A
PPLICATION
N
OTES
& D
ESIGN
D
ATA
:
Application Notes and design data including S-
parameters are available; please contact
Filtronic Compound Semiconductors Ltd.
D
ISCLAIMERS
:
This product is not designed for use in any
space based or life sustaining/supporting
equipment.
O
RDERING
I
NFORMATION
:
P
ART
N
UMBER
FMS2027-000
D
ESCRIPTION
Die in Waffle-pack
(Gel-pak available on request)
4
Specifications subject to change without notice
Filtronic Compound Semiconductors Ltd
Fax: +44 (0) 1325 306177
Email: sales@filcs.com
Tel: +44 (0) 1325 301111
Website:
www.filtronic.com
创意市集
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
