MH88437-P
Data Access Arrangement
Advance Information
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FAX and Modem interface (V.34/V.34+)
Designed to work at data rates up to 56kbits
External programmable line and network
balance impedances
Programmable DC termination characteristics
IEC950 recognised component
Transformerless 2-4 Wire conversion
Integral Loop Switch
Dial Pulse and DTMF operation
Accommodates parallel phone detection
Line state detection outputs:
-loop current/ringing voltage/line voltage
+5V operation, low on-hook power (25mW)
Full duplex voice and data transmission
On-Hook reception from the line
Meets French current limit requirements
Conforms to German dial pulse standards
Approvable to UL 1950
Industrial Temperature Range Available
•
•
DS5060
ISSUE 4
October 1998
Package Information
MH88437AD-P 28 Pin DIL Package
MH88437AS-P 28 Pin SM Package
0˚C to 70˚C
MH88437AD-PI Ind. Temp. DIL Variant
-40˚C to +80˚C
MH88437AS-PI Ind. Temp. SM Variant
-40˚C to + 80˚C
Telemetry
Set Top Boxes
Description
The Mitel MH88437 Data Access Arrangement
(D.A.A.) provides a complete interface between
audio or data transmission equipment and a
telephone line. All functions are integrated into a
single thick film hybrid module which provides high
voltage isolation, very high reliability and optimum
circuit design, needing a minimum of external
components.
The impedance and network balance are externally
programmable, as are the DC termination
characteristics, making the device suitable for most
countries worldwide.
Applications
Interface to Central Office or PABX line for:
• FAX/Modem
• Electronic Point of Sale
•
Security System
Isolation Barrier
VCC
VBIAS
AGND
CL
LC
VR+
VR-
NB1
NB2
THL cancellation
and line
impedance
matching circuit
VX
ZA
RV
LCD
LOOP
RS
Opto-
Isolation
TIP
RING
Input Buffer
&
Line Termination
Logic Input
Buffer
Isolation
Analog
Buffer
VLOOP1
VLOOP2
Isolation
Analog
Buffer
Ring & Loop
Buffer
Isolation
Network Connections
User Connections
Figure 1 - Functional Block Diagram
1
MH88437-P
NB1
NB2
VR+
VR-
VX
LC
ZA
AGND
VCC
VBIAS
LOOP
IC
RS
IC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
TIP
RING
IC
VLOOP1
VLOOP2
IC
SC
SC
IC
NP
NP
CL
RV
LCD
Advance Information
Figure 2 - Pin Connections
Pin Description
Pin #
1
2
3
4
5
6
7
8
9
10
11
12,
14
13
15
16
17
18
19
2
Name
NB1
NB2
VR+
VR-
VX
LC
ZA
AGND
V
CC
VBIAS
LOOP
IC
RS
LCD
RV
CL
NP
NP
Description
Network Balance 1.
External passive components must be connected between this pin and
NB2.
Network Balance 2.
External passive components must be connected between this pin and
NB1.
Differential Receive (Input).
Analog input from modem/fax chip set.
Differential Receive (Input).
Analog input from modem/fax chip set.
Transmit (Output).
Ground referenced (AGND) output to modem/fax chip set, biased at
+2.0V.
Loop Control (Input).
A logic 1 applied to this pin activates internal circuitry which provides
a DC termination across Tip and Ring. This pin is also used for dial pulse application.
Line Impedance.
Connect impedance matching components from this pin to Ground
(AGND).
Analog Ground.
4-Wire 0V reference connect to mains earth (ground).
Positive Supply Voltage.
+5V.
Internal Reference Voltage.
+2.0V reference voltage. This pin should be decoupled
externally to AGND, typically with a 10
µF
6.3V capacitor
.
Loop (Output).
The output voltage on this pin is proportional to the line voltage across Tip -
Ring, scaled down by a factor of 50.
Internal Connection.
No connection should be made to this pin externally.
Ringing Sensitivity.
Connecting a link or resistor between this pin and LOOP (pin 11) will
vary the ringing detection sensitivity of the module.
Loop Condition Detect (Output).
Indicates the status of loop current.
Ringing Voltage Detect (Output).
The RV output indicates the presence of a ringing voltage
applied across the Tip and Ring leads.
Current Limit.
A logic 0 applied to this pin activates internal circuitry which limits the loop
current.
No Pin.
Isolation Barrier, fitted, no pin fitted in this position.
No Pin.
Isolation barrier, no pin fitted in this position
Advance Information
Pin Description (continued)
Pin #
20,23
26
21,22
24
25
27
28
Name
IC
SC
VLOOP2
VLOOP1
RING
TIP
Description
MH88437-P
Internal Connection.
No connection should be made to this pin externally.
Short Circuit.
These two pins should be connected to each other via a 0Ω link.
Loop Voltage Control Node 2.
Used to set DC termination characteristics.
Loop Voltage Control Node 1.
Used to set DC termination characteristics.
Ring Lead.
Connects to the “Ring” lead of the telephone line.
Tip Lead.
Connects to the “Tip” lead of the telephone line.
applications the MH88437 will comply with
Luxembourg and Italian specifications. For approval
in Denmark and Sweden the TRB21 route is
recommended.
Approval specifications are regularly changing and
the relevant specification should always be consulted
before commencing design.
Functional Description
The device is a Data Access Arrangement (D.A.A.). It
is used to correctly terminate a 2-Wire telephone
line. It provides a signalling link and a 2-4 Wire line
interface between an analog loop and subscriber
data transmission equipment, such as Modems,
Facsimiles (Fax’s), Remote Meters, Electronic Point
of Sale equipment and Set Top Boxes.
Line Termination
Isolation Barrier
The device provides an isolation barrier capable of
meeting the supplementary barrier requirements of
the international standard IEC 950 and the national
variants of this scheme such as EN 60950 for
European applications and UL 1950 for North
American applications.
When Loop Control (LC) is at a logic 1, a line
termination is applied across Tip and Ring. The
device can be considered off-hook and DC loop
current will flow. The line termination consists of both
a DC line termination and an AC input impedance. It
is used to terminate an incoming call, seize the line
for an outgoing call, or if it is applied and
disconnected at the required rate, can be used to
generate dial pulses.
The DC termination resembles approximately 300Ω
resistance, which is loop current dependent.
Furthermore, it can be programmed to meet different
national requirements. For normal operation
VLOOP3 should be open circuit and a resistor (R2)
should be fitted between VLOOP1 and VLOOP2, as
shown in Figure 4.
The approval specification will give a DC mask
characteristic that the equipment will need to comply
to. The DC mask specifies the amount of current the
DAA can sink for a given voltage across tip and ring.
Graph 1 shows how the voltage across tip and ring
varies with different resistors (R2) for a given loop
current.
External Protection Circuit
An External Protection Circuit assists in preventing
damage to the device and the subscriber equipment,
due to over-voltage conditions. See Application Note
MSAN-154 for recommendations.
Suitable Markets
The MH88437 has features such as programmable
line and network balance impedance, programmable
DC termination and a supplementary isolation
barrier. For countries that do not need to meet the
French and German requirements there is a pin for
pin compatible device the MH88435.
There are, however, a small number of countries with
a 100MΩ leakage requirement that this device does
not meet. These are Belgium, Greece, Italy,
Luxembourg,
Spain
and
Poland.
Although
Luxembourg will now accept TBR21 and there are
exceptions to the Italian specification, in most
Network Balance
The network balance impedance of the device can
be programmed by adding external components By
3
MH88437-P
40
Advance Information
35
30
Iloop=15mA
25
V(t-r)
Iloop=20mA
Iloop=26mA
20
15
10
5
0
50
150
250
350
450
550
650
750
850
950
R2(kOhms)
Figure 3 - DC Programming Capability
applying a logic 0 to Pin 17, CL, the loop current will
be limited to below 60mA as required in France and
the European TBR21 specification. For all other
countries where current limiting is not required, CL
should be set to 1.
The AC input impedance should be set by the user to
match the line impedance.
To find the external programming components for
configuration 4, the following formula should be
used:
Zext = [(10 x R1)-1k3]+[(10 x R2)//(C1/10)]
e.g. If the required input impedance = 220Ω + (820Ω/
/115nF), the external network to be connected to ZA
will be:
ZA = 900Ω
+
(8k2Ω//12nF)
Where the input impedance (Z) = 600R the equation
can be simplified to:
ZA = (10 x Z) - 1k3Ω
For complex impedances the configuration shown in
Figure 4 (below) is most commonly found.
ZA = 4k7Ω
Note: A table of commonly used impedances can be
found in the DAA Application’s document MSAN-154.
Where Zext = external network connected between
ZA and AGND and Zint = 1.3kΩ (internal resistance)
between NB1 and NB2. For countries where the
balance impedance matches the line impedance, a
16kΩ resistor should be added between NB1 and
NB2.
Input Impedance
The MH88437 has a programmable input impedance
set by fitting external components between the ZA
pin and AGND.
R1
R2
C1
Figure 4 - Complex Impedances
4
Advance Information
Ringing Voltage Detection
The sensitivity of the ringing voltage detection
circuitry can be adjusted by applying an external
resistor (R7, Figure 5) between the RS and LOOP
pins. With a short circuit, the threshold sensitivity is
~10Vrms, therefore R7 = 30kΩ x (Desired threshold
voltage - 10Vrms).
Example: 300kΩ gives ~20Vrms and 600kΩ gives
~30Vrms.
An AC ringing voltage across Tip and Ring will cause
RV to output TTL pulses at the ringing frequency,
with an envelope determined by the ringing cadence.
MH88437-P
2-4 Wire Conversion
The device converts the balanced 2-Wire input,
presented by the line at Tip and Ring, to a ground
referenced signal at VX, biased at 2.0V. This
simplifies the interface to a modem chip set.
Conversely, the device converts the differential signal
input at VR+ and VR- to a balanced 2-Wire signal at
Tip and Ring. The device can also be used in a
single ended mode at the receive input, by leaving
VR+ open circuit and connecting the input signal to
VR- only. Both inputs are biased at 2.0V.
During full duplex transmission, the signal at Tip and
Ring consists of both the signal from the device to
the line and the signal from the line to the device.
The signal input at VR+ and VR- being sent to the
line, must not appear at the output VX. In order to
prevent this, the device has an internal cancellation
circuit, the measure of this attenuation is Transhybrid
Loss (THL).
The MH88437 has the ability to transmit analog
signals from Tip and Ring through to VX when on-
hook. This can be used when receiving caller line
identification information.
Parallel Phone and Dummy Ringer
An external parallel phone or dummy ringer circuit
can be connected across Tip and Ring as shown in
Figure 5. A Dummy Ringer is an AC load which
represents a telephone’s mechanical ringer.
In normal circumstances when a telephone is On-
Hook and connected to the PSTN, its AC (Ringer)
load is permanently presented to the network. This
condition is used by many PTT’s to test line
continuity, by placing a small AC current onto the line
and measuring the voltage across tip (A) and ring
(B).
Today’s telecom equipment may not have an AC load
present across tip and ring (e.g. modems), therefore
any testing carried out by the PTT will see an open
circuit across tip and ring. In this instance the PTT
assumes that the line continuity has been damaged.
To overcome this problem many PTT’s specify that a
"Dummy Ringer" is presented to the network at all
times. Ideally its impedance should be low in the
audio band and high at the ringing frequencies (e.g.
25Hz). Note that the requirement for the "Dummy
Ringer" is country specific.
Parallel phone detection is used mostly in set-top
box applications. This is when a modem call will
need to be disconnected from the central office by
the equipment when the parallel phone is in the off-
hook state. This is to allow the subscriber to make
emergency calls.
To detect this state, additional circuitry will be
required. Refer to Application Note MSAN-154.
Transmit Gain
The Transmit Gain of the MH88437 is the gain from
the differential signal across Tip and Ring to the
ground referenced signal at VX. The internal
Transmit Gain of the device is fixed as shown in the
AC Electrical Characteristics table. For the correct
gain, the Input Impedance of the MH88437, must
match the specified line impedance.
By adding an external potential divider to VX, it is
possible to reduce the overall gain in the application.
The output impedance of VX is approximately 10Ω
and the minimum resistance from VX to ground
should be 2kΩ.
Example: If R3 = R4 = 2kΩ, in Figure 5, the overall
gain would reduce by 6.0dB.
Receive Gain
The Receive Gain of the MH88437 is the gain from
the differential signal at VR+ and VR- to the
differential signal across Tip and Ring. The internal
Receive Gain of the device is fixed as shown in the
AC Electrical Characteristics table. For the correct
5
综合技术交流
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
