3M
™
Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
3000 Series
•
Military (with 3M’s 3518 and N3518 polarizing key)
and centerbump polarization
•
Optional ejector latches
•
Optional polarizing posts
•
Mounting holes for securing header to board
•
Dependable eye-of-the needle pin design
•
Optional high-temperature insulator
•
See Regulatory Information Appendix (RIA) for
chemical compliance information
Date Modified: April 30, 2008
TS-0478-B
Sheet 1 of 3
Physical
Insulation:
Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT)
Flammability: UL 94V-0
Color: Gray (PBT), Black (PCT)
Contact:
Material: Copper Alloy
Plating:
Underplating: 100 μ” [ 2.54 μm ] Nickel
Wiping Area: 30 μ” [ 0.76 μm ] Gold
Solder Tails: 100 μ” [ 2.54 μm ] Tin Lead or 300u” [7.62 um] Matte Tin (See Ordering Information)
Marking:
3M Logo, Part Identification Number and Orientation Triangle
Electrical
Current Rating:
1 A
Insulation Resistance:
>1 × 10
9
Ω
at 500 V
DC
Withstanding Voltage:
1,000 V
RMS
at Sea Level
Environmental
Temperature Rating:
-55°C to +105°C
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
-600T02
Header
with No Ejector/Latch
-620T02
Header
with Short Ejector/Latch
for 3M Sockets without Strain Relief
3000 Series
-630T02
Header
with Long Ejector/Latch
for 3M sockets with Strain Relief
.08
[2.0]
.08
[2.0]
.424
±
.010
[10.77]
.97 Ref
[24.6]
.573
±
.010
[14.55]
1.07 Ref
[27.2]
A
.68
[17.3]
.37 Ref
[9.4]
.46 Ref
[11.7]
D
.020
0.51
.100
2.54
REF.
.28
7.1
.185
4.70
.13
3.2
2X O .100 [2.54]
SEE NOTE #2
.100
2.54
POSITION #1
B
A
Notch B
(See Table)
.025
±
.002 Sq Typ
[0.64]
Position 1
Orientation
Triangle
.24
[6.1]
.35
[8.9]
Notch A
(See Table & Note 1)
Notch C
(See Table & Note 1)
.25
6.4
.34
8.6
REF.
A
.68
[17.3]
.30
[7.6]
.19
[4.8]
.020
[0.51]
.175
±
.010
[4.44]
Section A-A
Notes:
1. Notches A & C will accomodate 3M Polarizing Keys 3518 or N3518.
2. Accepts Rear and Front entry mounting hardware:
Rear Entry: #4-24 thread cutting screw
3M Part # 3341-5 (.116 [2.95] dia. mounting hole).
Front Entry (Prior to installation of latch): #2-56 Bolt and Nut
3M Part # 3341-6 (.106 [2.69] dia. mounting hole).
.21
[5.3]
C
A
.16
[4.1]
Tolerance Unless Noted
.0
.00
Inch
±
.1
Inch
(mm)
.000
[ ] Dimensions for
Reference only
±
.01
±
.005
C
TS-0478-B
Sheet 2 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
Pin Qty
3M Part
Number
Dimensions
A
B
C
D
Polarizing
Notches
Provided
3000 Series
Insertion platen
3442-00XX
10
14
16
20
24
26
30
34
40
50
60
64
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
.300 Min
[7.62]
Side to Side
Stackability
1.26 (32.1)
1.46 (37.2)
1.56 (39.7)
1.76 (44.8)
1.96 (49.9)
2.06 (52.4)
2.26 (57.5)
2.46 (62.6)
2.76 (70.2)
3.26 (82.9)
3.76 (95.6)
3.96 (100.7)
.106
[2.69]
or
(See Note 2)
See Note 3
1.105 (28.07)
1.305 (33.15)
1.405 (35.69)
1.605 (40.77)
1.805 (45.85)
1.905 (48.39)
2.105 (53.47)
2.305 (58.55)
2.605 (66.17)
3.105 (78.87)
3.605 (91.57)
3.805 (96.65)
.116
[2.95]
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
0.71 (18.0)
0.91 (23.1)
1.01 (25.6)
1.21 (30.7)
1.41 (35.8)
1.51 (38.3)
1.71 (43.4)
1.91 (48.5)
2.21 (56.1)
2.71 (68.8)
3.21 (81.5)
3.41 (86.6)
BC
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
3442-0048
3442-0049
3442-0050
3442-0051
3442-0052
3442-0053
3442-0054
3442-0055
3442-0056
3442-0057
3442-0058
3442-0059
R
R
Tail
Section
S
S
Compliant Section
4X R .009 Max
[0.23]
T
T
Mating
Area
.060
[1.52]
.100
±
.003
[2.54]
Position 1
.100
±
.003
[2.54]
.352
[8.94]
B
4X .002
±
.001
[0.05]
Break Edges
Section R-R
R .020 Sym
[0.51]
Section T-T
Section S-S
Pin Cross Sections
Hole Size for:
Preferred Drilled - ø.0453 ± .0005
Acceptable Drilled - ø.0453 +.0005
-.0010
After Etchback - ø.0460 Max
After Plating - .ø040 ± .003
Board thickness - .093 to .150
Plating:
.001 Minimum Copper plating thickness
.0003 Min Tin plating
Recommended Mounting Hole Pattern
Note:
3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M’s compliant
pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal
force is not less than 10 pounds per pin.
4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX)
styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally
equivalent to -2 & -3 roll pin latches)
If ordering Snap-In style latches separately, please use the chart below
Short Latch
Long Latch
Color
High Temp (PPA)
3505-30
3505-31
Gray
High Temp (PPA)
N3505-30B
N3505-31B
Black
Ordering Information
Prefix:
Blank = Std.Temp Gray (PBT): (TC Plating Req’d)
N = High Temp Black (PCT) (RB Plating Req’d)
X XXXX - 6X0T02XX
Plating suffix:
TC = 30 μ” Gold w/Tin-Lead Tails (App. E2 & C2 Apply)
RB = 30 μ” Gold w/Matte Tin Tails (App. E1 & C1 Apply)
3M Part Number
Assembly Equipment: Use 3442-00XX platen (see chart above) and
appropriate commercial arbor press to press header into pc board.
Latch/Ejector System:
0 = No latch/ejectors
2 = Short latch/ejectors
3 = Long latch/ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
TS-0478-B
Sheet 3 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part
does not
contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part
does
contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217A-D
汽车电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
