KISSLING
SINGLE POLE POWER RELAYS
Series 29 / 200A - from TE Connectivity (TE)
The economical 29 series single coil relays with 200 amps (A) are de-
veloped using our competence and expertise gathered over decades
of manufacturing to meet even the most demanding operating require-
ments.
This single coil system relay features high shock and vibration resis-
tance predominantly from its careful design and an optimized magnetic
circuit. The sealing technology used in these relays meets both the IP67
and IP6K9K (Steam pressure cleaning) protection standard. This relay
series is well suited for various applications in severe conditions.
Features
• Sealed housing conforms to IP6K9K
• Robust design
• Minimized coil current
• Variety of configuration options
• 6G shock and 4G vibration resistant
• Main contact current rated for continu
ous current and 100% duty cycle
• Efficient coil and magnetic circuit design
with switching properties and holding
current requirements
Applications
• Truck
• Bus
• Ground support vehicles
• Construction and agricultural vehicles
• Fork lift applications
Other important advantages are low heat generation in the contact
area based on low contact voltage drop, a compact design, low hold-
ing current, silver alloy contact material and the use of mechanical and
high thermal stability insulating compounds. Both the terminals and the
housing are protected against corrosion.
By equipping these relays with blow-out magnets, contact voltages are
also achievable up to 250VDC. The use of blow-out magnets are also
recommended for contact voltages over 40VDC and for inductive load
applications to maintain long contact life at all voltages.
Also available are various bracket styles to meet your installation
conditions and suppression devices to eliminate electromagnetic inter-
ference at the coil and optional auxiliary contacts.
Circuits
NO-Contact
NC-Contact
NO/NC-Contact
88
1
88
1
86
A1
88a
2
85
A2
88
1
86
A1
88a
2
85
A2
87
3
86
A1
88a
2
87a
4
85
A2
NO-Contact/Auxiliary-Contact
87y
88y
88
1
86
A1
87b
88b
88a
2
85
A2
Suppression diode
Suppression diode
Suppression diode
Suppression diode
Industrial & Commercial Transportation
/ Series 29 - 200A
Page 1
SERIES 29
200A
Specification
Technical Data
Temperature range
Protection
Shock
Vibration
Thread sizes / Torque
Electrical Characteristics
Min. Insulation resistance
After live or environment
Dielectric withstanding voltage
Max. Contact drop, initial
Contact drop after life test
Continuous current
Overload
Rated contact load
Resistive load
Cycles
Mechanical life
Coil Data
Voltage range
Nominal voltage
Pick up voltage max.
Drop out voltage min.
Coil resistance
Coil current approx.
Coil power approx.
100MΩ
50MΩ
1050VAC / 1min at 50Hz
150mV
175mV
200A
1600A - 1sec / 400A - 20sec
12 / 24 / 28VDC
220A
200.000
2.000.000 cycles
12VDC
9-16VDC
12VDC
9VDC
≤
2VDC
15Ω ± 10%
1A
10W
48VDC
200A
100.000
2.000.000 cycles
48VDC
36-54VDC
48VDC
36VDC
≤
8VDC
245Ω ± 10%
0.20A
10W
60VDC
200A
50.000
2.000.000 cycles
60VDC
45-68VDC
60VDC
45VDC
≤
10VDC
370Ω ± 10%
0.18A
10W
80VDC
120A
10.000
2.000.000 cycles
80VDC
60-90VDC
80VDC
60VDC
≤
20VDC
660Ω ± 10%
0.12A
10W
-40°C to +85°C
IEC 60529 & DIN 40050-9 - IP67 (0,2bar, 1min) and IP6K9K
6g / 11msec
4g / 50-2000Hz
M4 = 2.0 - 2.2Nm
|
M8 = 12 - 13Nm
24 / 28VDC
18-32VDC
28VDC
18VDC
≤
4VDC
62Ω ± 10%
0.40A
10W
Operating times NO-Contact relay
Operate
Bounce
Release
Wire Section
Mounting position
max. 40msec
max. 5msec
max. 20msec
min. 70mm
2
/ 0.039 sq.inch / AWG 2-0
optional
Industrial & Commercial Transportation
/ Series 29 - 200A
Page 2
SERIES 29
200A
Ordering Information
Part Number
example: 29.211.02
29.2 _ _._ _ _
Current
2
Current 200A
Options
A
B
Auxiliary contacts*
Magnetic blowout
(required over 40VDC)
Contacts
1
2
3
Make Contact NO
Change over NO/NC*
Break Contact NC
* Not possible for bottom mounting and NO/NC relay
Coil voltage
1
2
3
4
5
6
7
12V
24V
36V**
48V
60V
72V**
80V
* Only mounting type - 1 “Standard side mounting”
Mounting
1
2
3
4
Standard side mounting
Short form side
Bottom mounting
Long form side
**Upon request
Suppression
0
1
Without suppression
With suppression
te.com
TE Connectivity, TE, TE connectivity (logo), KISSLING (logo) and KISSLING (word) are trademarks owned or licensed by the TE Connectivity
family of companies. All other logos, products and/or company names referred to herein might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be
reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use.
TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case
will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product.
Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2020 TE Connectivity | All Rights Reserved.
K1166699 | Version 08/2020
Industrial & Commercial Transportation
/ Series 29 - 200A
Page 4
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
