LG2
Specifications
■
Ratings
Item Detected voltage
Rated voltage
Load
Setting range
Rated carry
current
Control output
Switching capacity
Rated
operating
voltage
Rated operating current
Resistive
load
(cosφ = 1)
5A
2A
5A
0.2 A
Inductive
load
(cosφ = 0.4,
L/R = 7 ms)
3A
1.2 A
2A
0.1 A
Power/VA
Must-operate Must-release
consumption (SET) voltage
(RESET)
(percentage
voltage
of rated
(percentage
value)
of rated
value)
5 VA max.
75% to 120%
70% to 115%
Model
LG2-AB
100 VAC
200 VAC
50/60 Hz
110 VAC
50/60 Hz
LG2-DB
12 VDC
24 VDC
48 VDC
100 VDC
3 W max.
5A
100 VAC
200 VAC
28 VDC
110 VDC
80% to 110%
75% to 120%
75% to 105%
70% to 115%
Note: 1.
2.
3.
4.
Set the must-operate voltage higher than the must-release voltage by at least 5% of the rated value.
Smoothing is required for the detected DC voltage.
The maximum applied voltage is 120% of the rated value.
Special models enabling a rated voltage of 220 V are available. The setting range for these models is 80% to 110%.
■
Characteristics
Repeat accuracy
Variation due to
temperature
change
Operate time
Release time
Insulation
resistance
±3%
max. (with voltage fluctuations at the rate
of 1 V/s)
±5%
max. (within the range 20
°C
+20/−30
°C)
0.5 s max. (when input changes from 0 V to
120% must-operate voltage)
0.5 s max. (when input changes from 120% of
the must-release voltage to 0 V)
10 MΩ min. at 500 VDC (between electric
circuitry and mounting panel)
Dielectric strength
2,000 VAC, 50/60 Hz for 1 min (between electric
circuitry and mounting panel)
Vibration
Shock
Service life
Malfunction: 16.7 Hz, 1-mm double amplitude
Destruction: 294 m/s
2
(approx. 30 G)
Mechanically:
10,000,000 operations min.
Electrically:
50,000 operations min. (at max. applicable
load)
Approx. 100 g
−10
to 40°C (with no condensation)
Weight
Ambient
operating
temperature
2
LG2
Connections
■
Terminal Arrangement
4
3
2
1
8
5
6
7
3
2
1
8
4
5
6
7
(+)
(−)
The polarity indication for
terminals and applies
to the DC model (LG2-DB).
(The above diagram shows
the rear side of the Relay.)
(The above diagram shows
the rear side of the Relay.)
Note: 1.
*Type LG2-DB is not equipped with the rectifier circuit.
2.
With type LG2-DB, care should be taken to the polarity of
the power supply.
Nomenclature
VOLTAGE
SENSOR
LG2-DB
RESET knob
RESET
70to115%
VOLTAGE
SET
75to120%
12VDC
SET knob
Setting Method
Operate Value
Input the actual voltage to be set, and set the SET knob to the point
at which the Relay operates.
Release Value
•
With the Relay operating, turn the RESET knob counterclockwise
as far as it will go, and adjust the voltage to the value to be set.
Then, gradually turn the RESET knob clockwise until it reaches the
point where the Relay is released.
Note:
After completing the settings, check the settings for the operate
and release values by increasing/decreasing the input voltage.
•
The LG2 can be used for undervoltage detection by using the
RESET knob for the operate value and the SET knob for the
release value. The Relay will normally be ON, however, and so the
internal temperature will rise, and this will affect the product service
life.
3
LG2
Dimensions
Note:
All units are in millimeters unless otherwise indicated.
LG2-AB, LG2-DB
Mounting Height of
Sensor with Socket
50.5 max.
LG2
107
38.5 max.
86
91
LG2
13.6
16
PF08 (order separately)
PF083A (order separately)
Accessories (Order Separately)
Connecting Socket
PF083A Front Connecting Socket
Eight, M3.5
×
7
sems screws
7
4
Terminal
Arrangement
2 1 8 7
35.4
Mounting
Holes
Two, M4 or 4.5-dia. holes
Applicable Models
APR-S
LG2
Two, 4.2-dia.
holes
52 max.
33±
0.2
Note:
Mount sockets to applicable models
so that
points downwards.
4
33
41 max.
3.5
2
21 max.
3 4 5 6
(Top View)
PL08 Back Connecting Socket (Solder Terminals)
3.5
4
1
Terminal
Arrangement
Two, 2-dia. holes
Mounting
Holes
Two, 3.5-dia. or two, M3
socket mounting holes
4
3
2
1
5
6
7
8
50.5 max.
40
30 dia.
3.9
35 max.
Applicable Models
SE
APR-S
SDV
LG2
SAO
40±
0.3
31-dia. hole
Approx. 20.5
(Top View)
Socket Mounting Track (for PF083A)
PFP-100N/PFP-50N Socket Mounting Track
Hold-down Clip
Use the Hold-down Clip to secure the Voltage Sensor on the Con-
necting Socket, as well as to prevent faulty contact.
Type of Socket
Applicable type of
Hold-down Clip
PFC-A7
PLC-8
7.3±
0.15
PF083A
PL08
4.5
15
25 10 25
1,000 (500)*
25 10 25
15 (5)*
35±
0.3
27±
0.15
1
* The dimensions given in parentheses are for the PFP-50N Socket Mounting Track.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply
by
0.03937. To convert grams into ounces, multiply
by
0.03527.
In the interest of product improvement, specifications are subject to change without notice.
4
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty.
Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy.
Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s
analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See
http://www.omron.com/global/
or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s
Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application.
Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.10
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
