Freescale Semiconductor
Data Sheet: Technical Data
Document Number: K50P144M100SF2V2
Rev. 3, 6/2013
Supports the following:
MK50DN512CLQ10,
MK50DN512CMD10,
MK50DX256CMD10
Features
• Operating Characteristics
– Voltage range: 1.71 to 3.6 V
– Flash write voltage range: 1.71 to 3.6 V
– Temperature range (ambient): -40 to 85°C
• Performance
– Up to 100 MHz ARM Cortex-M4 core with DSP
instructions delivering 1.25 Dhrystone MIPS per
MHz
• Memories and memory interfaces
– Up to 512 KB program flash memory on non-
FlexMemory devices
– Up to 128 KB RAM
– Serial programming interface (EzPort)
– FlexBus external bus interface
• Clocks
– 3 to 32 MHz crystal oscillator
– 32 kHz crystal oscillator
– Multi-purpose clock generator
• System peripherals
– Multiple low-power modes to provide power
optimization based on application requirements
– Memory protection unit with multi-master
protection
– 16-channel DMA controller, supporting up to 63
request sources
– External watchdog monitor
– Software watchdog
– Low-leakage wakeup unit
• Security and integrity modules
– Hardware CRC module to support fast cyclic
redundancy checks
– 128-bit unique identification (ID) number per chip
• Human-machine interface
– Low-power hardware touch sensor interface (TSI)
– General-purpose input/output
• Analog modules
– Two 16-bit SAR ADCs
– Programmable gain amplifier (PGA) (up to x64)
integrated into each ADC
– Two 12-bit DACs
– Two operational amplifiers
– Two transimpedance amplifiers
– Three analog comparators (CMP) containing a 6-bit
DAC and programmable reference input
– Voltage reference
• Timers
– Programmable delay block
– Eight-channel motor control/general purpose/PWM
timer
– Two 2-channel quadrature decoder/general purpose
timers
– Periodic interrupt timers
– 16-bit low-power timer
– Carrier modulator transmitter
– Real-time clock
• Communication interfaces
– USB full-/low-speed On-the-Go controller with on-
chip transceiver
– Three SPI modules
– Two I2C modules
– Six UART modules
– Secure Digital host controller (SDHC)
– I2S module
K50 Sub-Family
K50P144M100SF2V2
Freescale reserves the right to change the detail specifications as may be
required to permit improvements in the design of its products.
© 2012–2013 Freescale Semiconductor, Inc.
Table of Contents
1 Ordering parts...........................................................................4
1.1 Determining valid orderable parts......................................4
2 Part identification......................................................................4
2.1 Description.........................................................................4
2.2 Format...............................................................................4
2.3 Fields.................................................................................4
2.4 Example............................................................................5
3 Terminology and guidelines......................................................5
3.1 Definition: Operating requirement......................................5
3.2 Definition: Operating behavior...........................................6
3.3 Definition: Attribute............................................................6
3.4 Definition: Rating...............................................................7
3.5 Result of exceeding a rating..............................................7
3.6 Relationship between ratings and operating
requirements......................................................................7
3.7 Guidelines for ratings and operating requirements............8
3.8 Definition: Typical value.....................................................8
3.9 Typical value conditions....................................................9
4 Ratings......................................................................................10
4.1 Thermal handling ratings...................................................10
4.2 Moisture handling ratings..................................................10
4.3 ESD handling ratings.........................................................10
4.4 Voltage and current operating ratings...............................10
5 General.....................................................................................11
5.1 AC electrical characteristics..............................................11
5.2 Nonswitching electrical specifications...............................11
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
Voltage and current operating requirements.........12
LVD and POR operating requirements.................13
Voltage and current operating behaviors..............13
Power mode transition operating behaviors..........15
Power consumption operating behaviors..............16
EMC radiated emissions operating behaviors.......19
Designing with radiated emissions in mind...........20
Capacitance attributes..........................................20
6.8.5
6.8.6
6.8.7
6.8.8
6.8.9
6.6.7
6.6.6
6 Peripheral operating requirements and behaviors....................23
6.1 Core modules....................................................................23
6.1.1
6.1.2
Debug trace timing specifications.........................23
JTAG electricals....................................................24
6.2 System modules................................................................27
6.3 Clock modules...................................................................27
6.3.1
6.3.2
6.3.3
MCG specifications...............................................27
Oscillator electrical specifications.........................29
32 kHz oscillator electrical characteristics.............32
6.4 Memories and memory interfaces.....................................32
6.4.1
6.4.2
6.4.3
Flash electrical specifications................................32
EzPort switching specifications.............................34
Flexbus switching specifications...........................35
6.5 Security and integrity modules..........................................38
6.6 Analog...............................................................................38
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
ADC electrical specifications.................................38
CMP and 6-bit DAC electrical specifications.........46
12-bit DAC electrical characteristics.....................49
Op-amp electrical specifications...........................52
Transimpedance amplifier electrical
specifications — full range....................................53
Transimpedance amplifier electrical
specifications — limited range..............................54
Voltage reference electrical specifications............55
6.7 Timers................................................................................56
6.8 Communication interfaces.................................................56
6.8.1
6.8.2
6.8.3
6.8.4
USB electrical specifications.................................56
USB DCD electrical specifications........................57
USB VREG electrical specifications......................57
DSPI switching specifications (limited voltage
range)....................................................................57
DSPI switching specifications (full voltage range).59
Inter-Integrated Circuit Interface (I2C) timing........61
UART switching specifications..............................62
SDHC specifications.............................................62
I2S/SAI switching specifications............................63
5.3 Switching specifications.....................................................20
5.3.1
5.3.2
Device clock specifications...................................20
General switching specifications...........................21
6.9 Human-machine interfaces (HMI)......................................69
6.9.1
TSI electrical specifications...................................69
5.4 Thermal specifications.......................................................22
5.4.1
5.4.2
Thermal operating requirements...........................22
Thermal attributes.................................................22
7 Dimensions...............................................................................70
7.1 Obtaining package dimensions.........................................70
K50 Sub-Family Data Sheet, Rev. 3, 6/2013.
2
Freescale Semiconductor, Inc.
8 Pinout........................................................................................70
8.1 K50 signal multiplexing and pin assignments....................70
8.2 K50 pinouts.......................................................................76
9 Revision history.........................................................................78
K50 Sub-Family Data Sheet, Rev. 3, 6/2013.
Freescale Semiconductor, Inc.
3
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device, go to
freescale.com
and perform a part number search for the
following device numbers: PK50 and MK50.
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
2.2 Format
Part numbers for this device have the following format:
Q K## A M FFF R T PP CC N
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Q
K##
A
M
Qualification status
Kinetis family
Key attribute
Flash memory type
Description
Values
• M = Fully qualified, general market flow
• P = Prequalification
• K50
• D = Cortex-M4 w/ DSP
• F = Cortex-M4 w/ DSP and FPU
• N = Program flash only
• X = Program flash and FlexMemory
Table continues on the next page...
K50 Sub-Family Data Sheet, Rev. 3, 6/2013.
4
Freescale Semiconductor, Inc.
Terminology and guidelines
Field
FFF
Description
Program flash memory size
•
•
•
•
•
•
•
32 = 32 KB
64 = 64 KB
128 = 128 KB
256 = 256 KB
512 = 512 KB
1M0 = 1 MB
2M0 = 2 MB
Values
R
Silicon revision
• Z = Initial
• (Blank) = Main
• A = Revision after main
• V = –40 to 105
• C = –40 to 85
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FM = 32 QFN (5 mm x 5 mm)
FT = 48 QFN (7 mm x 7 mm)
LF = 48 LQFP (7 mm x 7 mm)
LH = 64 LQFP (10 mm x 10 mm)
MP = 64 MAPBGA (5 mm x 5 mm)
LK = 80 LQFP (12 mm x 12 mm)
LL = 100 LQFP (14 mm x 14 mm)
MC = 121 MAPBGA (8 mm x 8 mm)
LQ = 144 LQFP (20 mm x 20 mm)
MD = 144 MAPBGA (13 mm x 13 mm)
MJ = 256 MAPBGA (17 mm x 17 mm)
5 = 50 MHz
7 = 72 MHz
10 = 100 MHz
12 = 120 MHz
15 = 150 MHz
T
PP
Temperature range (°C)
Package identifier
CC
Maximum CPU frequency (MHz)
N
Packaging type
• R = Tape and reel
• (Blank) = Trays
2.4 Example
This is an example part number:
MK50DN512ZVMD10
3 Terminology and guidelines
3.1 Definition: Operating requirement
An
operating requirement
is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
K50 Sub-Family Data Sheet, Rev. 3, 6/2013.
Freescale Semiconductor, Inc.
5
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
