Cylinder Sensor
E2SS
CSM_E2SS_DS_E_1_1
Mounts to Any Type of Cylinder
• One shape of Sensor for all types of cylinders.
• Mounting is simple even in narrow spaces.
• Operating condition is confirmable at a glance.
Refer to
Safety Precautions
on page 4.
For the most recent information on models that have been certified
for safety standards, refer to your OMRON website.
Ordering Information
Sensors
(Dimensions
➜
page 4)
Series
Standard Models
E2SS-M
Connection method
Model
NPN output
E2SS-MC1 2M
PNP output
E2SS-MB1 2M
Pre-wired (2 m)
M12 Pre-wired connector
(0.3 m)
Magnetic Field Immune Models
E2SS-W
M12 Connector
E2SS-MC1-M1J 0.3M
E2SS-MB1-M1J 0.3M
E2SS-WC1-P1
E2SS-WB1-P1
Accessories (Order Separately)
Mounting Brackets
A Mounting Bracket is not provided with the Sensor and must be ordered separately as required.
Series
Round
Applicable cylinders
Cylinder diameter or groove width
8 to 25 mm dia.
25 to 63 mm dia.
32 to 40 mm dia.
50 to 63 mm dia.
80 to 100 mm dia.
160 to 200 mm dia.
Not necessary (mounted directly)
7 mm
9.4 mm
11.5 mm
12.6 mm
-
Model
E2SS-MR1
E2SS-MR2
E2SS-MT1
E2SS-MT2
E2SS-MT3
E2SS-MT4
E2SS-MV1
E2SS-MV2
E2SS-MV3
E2SS-MV4
E2SS-WV1
Tie-rod
E2SS-M
T-groove
Dovetail-groove
E2SS-W
T-groove or dovetail-groove
Sensor I/O Connectors (M12, Sockets on One Cable End)
(Required for models for Connectors and with Pre-wired Connectors.) A Connector is not provided with the Sensor. Be sure to order a
Connector separately.
(Dimensions
➜
XS2F)
Appearance
Cable length
Sensor I/O Connector model number Applicable Proximity Sensor model number
Straight
2m
XS2F-D421-DC0-F
5m
L-shape
2m
5m
XS2F-D421-GC0-F
XS2F-D422-DC0-F
XS2F-D422-GC0-F
E2SS-M@1-M1J
E2SS-W@1-P1
1
E2SS
Ratings and Specifications
Model
Item
Power supply voltage
Detection sensitivity
(magnetic sensitivity)
Current consumption
Hysteresis
Repeat accuracy
Pass speed
Switching frequency
Control
output
Indicator
Operation mode
Protective circuits
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
(endurance)
Shock resistance (endurance)
Degree of protection
Connection method
Weight (when packed)
Materials
Accessories
Switching capacity
Residual voltage
Standard Models
E2SS-M Series
E2SS-MC1(-M1J)
E2SS-MB1(-M1J)
10 to 30 VDC (including ripple (p-p): 10 %)
2.8 mT max.
15 mA max.
1 mm max.
±0.1
mm max.
10 m/s max.
1 kHz max.
150 mA max.
2 V max. (Load current: 150 mA, Cable length: 2 m)
Operation indicator (yellow)
NPN open-collector,
NO (normally open)
PNP open-collector,
NO (normally open)
NPN open-collector,
NO (normally open)
PNP open-collector,
NO (normally open)
1 m/s max.
20 Hz max.
100 mA max.
2 V max. (Load current: 100 mA, Cable length: 2 m)
Magnetic Field Immune Models
*
E2SS-W Series
E2SS-WC1-P1
E2SS-WB1-P1
Power supply reverse polarity protection, output reverse polarity protection, and load short-circuit protection
Operating/Storage: -25 to 70°C (with no icing or condensation)
Operating/Storage: 35% to 95% (with no condensation)
50 MΩ min. (at 500 VDC) between charged parts and case
500 VAC, 50/60 Hz for 1 min between charged parts and case
10 to 55 Hz with 1.0-mm double amplitude for 2 hours each in X, Y, and Z directions
300 m/s
2
10 times each in X, Y, and Z directions
IEC 60529 IP67
Blank: Pre-wired (standard cable length: 2 m)
M12 connector
-M1J: Pre-wired M12 connector (cable length: 0.3 m)
Pre-wired models: Approx. 35 g
Pre-wired M12 connector models: Approx. 30 g
Case: PP, Cable: PUR
Instruction Manual, cable clip (one)
Approx. 25 g
Case: PA, Connector: PA
Instruction Manual, mounting screw (one)
* These models prevent malfunction in environments in which AC welding is being performed.
The Sensor will hold the ON or OFF control output condition when subjected to an AC magnetic field of 50 to 60 Hz and 10 to 100 mT.
When the field subsides, the Sensor returns to normal operation. (Standard models will malfunction under magnetic field noise of approximately 1 mT or higher.)
2
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty.
Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy.
Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s
analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See
http://www.omron.com/global/
or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s
Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application.
Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2013.5
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2013 All Right Reserved.
工作这点儿事
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
