Datasheet> 器件分类 > 无源元件> 电阻器> NWW1BN2R10

文档预览

NWW1BN2R10: 产品描述Fixed Resistor, Wire Wound, 1W, 2.1ohm, 500V, 0.1% +/-Tol, -50,50ppm/Cel,; 产品类别无源元件电阻器; 文件大小110KB，共4页; 制造商SEI(Stackpole Electronics Inc.); 官网地址https://www.seielect.com/; 标准

下载文档详细参数全文预览

NWW1BN2R10概述

Fixed Resistor, Wire Wound, 1W, 2.1ohm, 500V, 0.1% +/-Tol, -50,50ppm/Cel,

NWW1BN2R10规格参数

参数名称	属性值
是否Rohs认证	符合
Objectid	833779974
Reach Compliance Code	compliant
YTEOL	0
构造	Welded
JESD-609代码	e3
引线直径	0.64 mm
引线长度	38.1 mm
端子数量	2
最高工作温度	350 °C
最低工作温度	-25 °C
封装直径	2.8 mm
封装长度	9.5 mm
封装形式	Axial
包装方法	Tape
额定功率耗散 (P)	1 W
电阻	2.1 Ω
电阻器类型	FIXED RESISTOR
系列	NWW
技术	WIRE WOUND
温度系数	50 ppm/°C
端子面层	Matte Tin (Sn)
容差	0.1%
工作电压	500 V

文档预览

下载PDF文档

全文
预览

WW/MWW/NWW Series

General Purpose and Precision Wirewound Resistor

Features:

•

Stackpole Electronics, Inc.

Resistive Product Solutions

WWS offers miniature size at higher power rating

High performance for low cost

High power to size ratio

MWW – completely molded construction with welded terminations

Complete welded terminations

Tinned copper leads

Available in non-inductive styles

High temperature silicone coating

RoHS compliant

Higher operating temperatures may be available. Contact factory.

Electrical Specifications

Type / Code

MIL-R-26 Ref.

Dielectric

Strength

(V)

500V

1,000V

500V

1,000V

Power Rating

(Watts)

@ 25ºC

0.4W

1.5W

2.5W

6.5W

10W

Resitance Temperature

Coefficient

Ohmic Range(Ω) and Tolerance(1)

0.1%, 0.5%, 1% & 5%

Standard

0.1 - 2K

0.1 - 3K

0.1 - 7K

0.1 - 10K

0.1 - 3K

0.1 - 15K

0.1 - 22K

0.1 - 10K

0.1 - 30K

0.1 - 40K

0.1 - 22K

0.1 - 50K

0.1 - 40K

0.1 - 70K

0.1 - 50K

0.1 - 100K

0.1 - 150K

0.1 - 100K

0.1 - 2K

0.1 - 20K

0.1 - 40K

0.1 - 150K

Non-Inductive

0.1 - 1K

0.1 - 1.5K

0.1 - 3.5K

0.1 - 5K

0.1 - 1.5K

0.1 - 7.5K

0.1 - 11K

0.1 - 5K

0.1 - 15K

0.1 - 20K

0.1 - 11K

0.1 - 25K

0.1 - 20K

0.1 - 35K

0.1 - 25K

0.1 - 50K

0.1 - 75K

0.1 - 50K

(N)WWH

(N)WW1

(N)WW1A

RW-70

(N)WW2

RW-69

(N)WWS2

(N)WW2A

(N)WW3

RW-79

(N)WWS3

RW-69

(N)WW3A

(N)WW4

(N)WWS4

RW-79

(N)WW5

RW-67, RW-74

(N)WWS5

(N)WW7

(N)WWS7

RW-67, RW-74

(N)WW7B

(N)WW10

RW-78

(N)WWS10

(N)MWW1

RW-70

(N)MWW3

RW-79

(N)MWW5

RW-67, RW-74

(N)MWW10

RW-68, RW-74

(1) Lesser of√PR or maximum working voltage

< 1Ω = ±90ppm/ºC

1Ω to 10Ω = ±50ppmºC

>10Ω = ±20ppm/ºC

Please refer to the High Power Resistor Application Note (page 4) for more information on designing and

implementing high power resistor types.

Rev Date: 08/11/2011

This specification may be changed at any time without prior notice

Please confirm technical specifications before you order and/or use.

www.seielect.com

marketing@seielect.com

WW/MWW/NWW Series

General Purpose and Precision Wirewound Resistor

Stackpole Electronics, Inc.

Resistive Product Solutions

High Power Chip Resistors and Thermal Management

Stackpole has developed several surface mount resistor series in addition to our current sense resistors,

which have had higher power ratings than standard resistor chips. This has caused some uncertainty and

even confusion by users as to how to reliably use these resistors at the higher power ratings in their designs.

The data sheets for the RHC, RMCP, RNCP, CSR, CSRN, CSRF, CSS, and CSSH state that the rated

power assumes an ambient temperature of no more than 100 degrees C for the CSS / CSSH series and 70

degrees C for all other high power resistor series. In addition, IPC and UL best practices dictate that the

combined temperature on any resistor due to power dissipated and ambient air shall be no more than 105C.

At first glance this wouldn’t seem too difficult, however the graph below shows typical heat rise for the CSR

½ 100 milliohm at full rated power. The heat rise for the RMCP and RNCP would be similar. The RHC with

its unique materials, design, and processes would have less heat rise and therefore would be easier to

implement for any given customer.

The 102 degrees C heat rise shown here would indicate there will be additional thermal reduction techniques

needed to keep this part under 105C total hot spot temperature if this part is to be used at 0.75 watts of

power. However, this same part at the usual power rating for this size would have a heat rise of around 72

degrees C. This additional heat rise may be dealt with using wider conductor traces, larger solder pads and

land patterns under the solder mask, heavier copper in the conductors, vias through PCB, air movement, and

heat sinks, among many other techniques. Because of the variety of methods customers can use to lower

the effective heat rise of the circuit, resistor manufacturers simply specify power ratings with the limitations

on ambient air temperature and total hot spot temperatures and leave the details of how to best accomplish

this to the design engineers. Design guidelines for products in various market segments can vary widely so it

would be unnecessarily constraining for a resistor manufacturer to recommend the use of any of these

methods over another.

Note:

The final resistance value can be affected by the board layout and assembly process, especially the size of the

mounting pads and the amount of solder used. This is especially notable for resistance values

≤

50 mΩ.

This should be taken into account when designing.

Rev Date: 08/11/2011

This specification may be changed at any time without prior notice

Please confirm technical specifications before you order and/or use.

www.seielect.com

marketing@seielect.com

推荐资源

利用MEMS惯性感测技术实现应用变革: 本帖最后由雨中于 2014-9-27 22:09 编辑虽然MEMS(微电子机械系统)技术被用于安全气囊和汽车压力传感器领域已有二十年左右，但却是任天堂Wii和苹果iPhone= ......; 雨中 ADI 工业技术

关于USB管道名的问题 (八百里加急): 小弟现在在开发上位机程序用到USB 通讯 ,但是驱动资料上只给除了两个管道名由于种种原因这两个都不符合要求我该怎么样得到管道名 (用一个共享软件人家都可以得到的) 请高手 ......; darkgrass 嵌入式系统

【GD32L233C-START测评】基于串行通讯的触摸屏控制LED: 本帖最后由 jinglixixi 于 2022-2-13 10:38 编辑使用迪文智能屏的触摸操作可进行参数的设置，所设置的参数又有可以借助串行通讯来输出参数值。若接收该参数，则可以对外设加以控制。 ......; jinglixixi GD32 MCU

关于quartus 分频器: 分频器一共可以出现几个？我做东西显示分频器只能用两个，但是有人说是一条线上最多两个，并且有人用了三个分频器了· ··...; 一个人_ FPGA/CPLD

LED驱动必备（变压器相关）: LED驱动和目前都是用开关电源之IC 所以免不了磁性器件变压器的设计 47855 希望对各位LED爱好者使用者有用...; czf0408 LED专区

谁能给个10A高精度恒流源电路，电流精度0.1mA: 本帖最后由孤独老人于 2017-8-26 00:09 编辑哪位大哥大姐能给个10A稳定可靠的高精度恒流源电路，电流精度0.1mA，希望电流跳动在0.1mA ...; 孤独老人模拟电子

器件捷径: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

热门器件

开源项目推荐更多

热门活动更多

热门文章更多

技术资料推荐更多