Preface
Thank you very much for making use of Toshiba microcomputer LSIs.
Before use this LSI, refer the section, “Points of Note and Restrictions”.
Especially, take care below cautions.
**CAUTION**
How to release the HALT mode
Usually, interrupts can release all halts status. However, the interrupts
=
(
NMI
,
INT0), which can release the HALT mode may not be able to do so if they are
input during the period CPU is shifting to the HALT mode (for about 3 clocks of
f
FPH
) with IDLE1 or STOP mode (RUN and IDLE2 are not applicable to this case).
(In this case, an interrupt request is kept on hold internally.)
If another interrupt is generated after it has shifted to HALT mode completely,
halt status can be released without difficultly. The priority of this interrupt is
compare with that of the interrupt kept on hold internally, and the interrupt with
higher priority is handled first followed by the other interrupt.
TMP93CS44/S45
Low Voltage/Low Power
CMOS 16-bit Microcontrollers
TMP93CS44F/TMP93CS45F
1.
Outline and Device Characteristics
The TMP93CS44/TMP93CS45 are high-speed, advanced 16-bit microcontrollers developed for
controlling medium to large-scale equipment. The TMP93CS45 does not have a ROM, the
TMP93CS44 has a built-in ROM. Otherwise, the devices function in the same way.
The TMP93CS44F/TMP93CS45F are housed in 80-pin flat package (P-LQFP80-1212-0.50E).
The device characteristics are as follows:
(1) Original 16-bit CPU (900/L CPU)
•
•
•
•
•
TLCS-90 instruction mnemonic upward compatible
16-Mbyte linear address space
General-purpose registers and register bank system
16-bit multiplication/division and bit transfer/arithmetic instructions
Micro DMA: 4 channels (1.6
µs
per 2 bytes at 20 MHz)
(2) Minimum instruction execution time: 200 ns at 20 MHz
(3) Internal RAM: 2 Kbytes
Internal ROM:
TMP93CS44
TMP93CS45
64-Kbyte ROM
None
(4) External memory expansion
•
•
•
Can be expanded up to 16 Mbytes (for both programs and data)
AM8/
ΑΜ16
pin (Select the external data bus width)
Can mix 8- and 16-bit external data buses (Dynamic bus sizing)
(5) 8-bit timer: 4 channels
(6) 16-bit timer: 2 channels
030619EBP1
•
The information contained herein is subject to change without notice.
•
The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of TOSHIBA or others.
•
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general
can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer,
when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid
situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to
property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most
recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for
Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc..
•
The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal
equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are
neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or
failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control
instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made
at the customer’s own risk.
•
The products described in this document are subject to the foreign exchange and foreign trade laws.
•
TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law
and regulations.
•
For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter entitled Quality
and Reliability Assurance/Handling Precautions.
Purchase of TOSHIBA I
2
C components conveys a license under the Philips I
2
C Patent Rights to use
these components in an I
2
C system, provided that the system conforms to the I
2
C Standard
Specification as defined by Philips.
93CS44-1
2004-02-10
TMP93CS44/S45
(7) Serial interface: 2 channels
(8) Serial bus interface: 1 channel
•
•
I
2
C bus mode
Clocked-synchronous 8-bit serial interface mode
(9) 10-bit AD converter: 8 channels
(10) High current output: 8 ports
(11) Watchdog timer
(12) Bus width/wait controller: 3 blocks
(13) Interrupt functions: 33
•
•
•
9 CPU interrupts
17 internal interrupts
7 external interrupts
7-level priority can be set (except
NMI
and INTWD)
(14) I/O ports
TMP93CS44
TMP93CS45
62 pins
44 pins
(15) Standby function: 4 HALT modes (RUN, IDLE2, IDLE1, STOP)
(16) Clock gear function
•
•
•
Dual clock operation
High-frequency clock can be changed from fc to fc/16
V
CC
=
2.7 to 5.5 V
(17) Wide range of operating voltage
(18) Package
Type Number
TMP93CS44F
TMP93CS45F
Package
P-LQFP80-1212-0.50E
93CS44-2
2004-02-10
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
