DATASHEET
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
General Description
The IDT1337 device is a low power serial real-time clock
(RTC) device with two programmable time-of-day alarms
and a programmable square-wave output. Address and
data are transferred serially through an I
2
C bus. The device
provides seconds, minutes, hours, day, date, month, and
year information. The date at the end of the month is
automatically adjusted for months with fewer than 31 days,
including corrections for leap year. The clock operates in
either the 24-hour or 12-hour format with AM/PM indicator.
IDT1337
Features
•
Real-Time Clock (RTC) counts seconds, minutes, hours,
day, date, month, and year with leap-year compensation
valid up to 2100
•
Packaged in 8-pin MSOP, 8-pin SOIC, or 16-pin SOIC
(surface-mount package with an integrated crystal)
Applications
•
•
•
•
•
•
Telecommunication (Routers, Switches, Servers)
Handhelds (GPS, POS terminals, MP3 players)
Set-Top Box, Digital Recording,
Office (Fax/Printers, Copiers)
Medical (Glucometer, Medicine Dispensers)
Other (Thermostats, Vending Machines, Modems, Utility
Meters, Digital Photo Frame devices)
•
•
•
•
I
2
C Serial interface (Normal and Fast modes)
Two time-of-day alarms
Oscillator Stop Flag
Programmable square-wave output defaults to 32 kHz on
power-up
•
Operating voltage of 1.8 to 5.5 V
•
Industrial temperature range (-40 to +85°C)
Block Diagram
VCC
Crystal inside package
for 16-pin SOIC ONLY
X1
1 Hz/4.096 kHz/
8.192 kHz/32.768 kHz
32.768 kHz
Oscillator and
Divider
MUX/
Buffer
SQW/INTB
INTA
X2
Control
Logic
Clock,
Calendar
Counter
SCL
SDA
I
2
C
Interface
1 Byte
Control
7 Bytes
Buffer
Alarm
Registers
GND
IDT™
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
1
IDT1337
REV H 120208
IDT1337
REA LTIME CLOCK WITH SERIAL INTERFACE
RTC
Pin Assignment
(8-pin MSOP/SOIC)
X1
X2
INTA
GND
1
2
3
4
8
VCC
SQW/INTB
SCL
SDA
Pin Assignment
(16-pin SOIC)
SCL
SQW/INTB
VCC
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
16
15
14
SDA
GND
INTA
NC
NC
NC
NC
NC
IDT1337
7
6
5
IDT1337C
13
12
11
10
9
Pin Descriptions
Pin
Number
MSOP SOIC
1
2
—
—
Pin
Name
X1
X2
Pin Description/Function
Connections for standard 32.768 kHz quartz crystal. The internal oscillator circuitry is
designed for operation with a crystal having a specified load capacitance (CL) of 7 pF. An
external 32.768 kHz oscillator can also drive the IDT1337. In this configuration, the X1 pin
is connected to the external oscillator signal and the X2 pin is left floating.
Interrupt output. When enabled, INTA is asserted low when the time/day/date matches the
values set in the alarm registers. This pin is an open-drain output and requires an external
pull-up resistor (10 kΩ typical).
Connect to ground. DC power is provided to the device on these pins.
Serial data input/output. SDA is the input/output pin for the I
2
C serial interface. The SDA pin
is an open-drain output and requires an external pull-up resistor (2 kΩ typical).
Serial clock input. SCL is used to synchronize data movement on the serial interface. The
SCL pin is an open-drain output and requires an external pull-up resistor (2 kΩ typical).
3
4
5
6
14
15
16
1
INTA
GND
SDA
SCL
7
2
Square-Wave/Interrupt output. Programmable square-wave or interrupt output signal. The
SQW/INT pin is an open-drain output and requires an external pull-up resistor (10 kΩ
SQW/INTB
typical). This pin can also function as an additional interrupt pin under certain conditions
(see page 6 for details).
VCC
NC
Primary power supply. DC power is applied to this pin.
No connect. These pins are unused and must be connected to ground.
8
—
3
4 - 13
IDT™
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
2
IDT1337
REV H 120208
IDT1337
REA LTIME CLOCK WITH SERIAL INTERFACE
RTC
Typical Operating Circuit
V
CC
V
CC
CRYSTAL
V
CC
2k
CPU
2k
X1
SCL
SDA
X2
V
CC
SQW/INTB
10k
10k
IDT1337
GND
INTA
Detailed Description
Communications to and from the IDT1337 occur serially
over an I
2
C bus. The IDT1337 operates as a slave device on
the serial bus. Access is obtained by implementing a START
condition and providing a device identification code,
followed by data. Subsequent registers can be accessed
sequentially until a STOP condition is executed. The device
is fully accessible through the I
2
C interface whenever VCC
is between 5.5 V and 1.8 V. I
2
C operation is not guaranteed
when VCC is below 1.8 V. The IDT1337 maintains the time
and date when VCC is as low as 1.3 V.
The following sections discuss in detail the Oscillator block,
Clock/Calendar Register Block and Serial I
2
C block.
Effective Load Capacitance
Please see diagram below for effective load capacitance
calculation. The effective load capacitance (CL) should
match the recommended load capacitance of the crystal in
order for the crystal to oscillate at its specified parallel
resonant frequency with 0ppm frequency error.
Oscillator Block
Selection of the right crystal, correct load capacitance and
careful PCB layout are important for a stable crystal
oscillator. Due to the optimization for the lowest possible
current in the design for these oscillators, losses caused by
parasitic currents can have a significant impact on the
overall oscillator performance. Extra care needs to be taken
to maintain a certain quality and cleanliness of the PCB.
Crystal Selection
The key parameters when selecting a 32 kHz crystal to work
with IDT1337 RTC are:
•
Recommended Load Capacitance
•
Crystal Effective Series Resistance (ESR)
•
Frequency Tolerance
In the above figure, X1 and X2 are the crystal pins of our
device. Cin1 and Cin2 are the internal capacitors which
include the X1 and X2 pin capacitance. Cex1 and Cex2 are
the external capacitors that are needed to tune the crystal
frequency. Ct1 and Ct2 are the PCB trace capacitances
between the crystal and the device pins. CS is the shunt
capacitance of the crystal (as specified in the crystal
manufacturer's datasheet or measured using a network
analyzer).
IDT™
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
3
IDT1337
REV H 120208
IDT1337
REA LTIME CLOCK WITH SERIAL INTERFACE
RTC
Note:
IDT1337CSRI integrates a standard 32.768 kHz
crystal in the package and contributes an additional
frequency error of 10ppm at nominal
V
CC
(+3.3 V) and
T
A
=
+25°C.
to the GND layer. This helps to keep noise generated by
the oscillator circuit locally on this separated island. The
ground connections for the load capacitors and the
oscillator should be connected to this island.
ESR (Effective Series Resistance)
Choose the crystal with lower ESR. A low ESR helps the
crystal to start up and stabilize to the correct output
frequency faster compared to high ESR crystals.
PCB Layout
Frequency Tolerance
The frequency tolerance for 32 KHz crystals should be
specified at nominal temperature (+25°C) on the crystal
manufacturer datasheet. The crystals used with IDT1337
typically have a frequency tolerance of +/-20ppm at +25°C.
Specifications for a typical 32 kHz crystal used with our
device are shown in the table below.
Parameter
Nominal Freq.
Series Resistance
Load Capacitance
1337
Symbol
f
O
ESR
C
L
Min
Typ
32.768
Max Units
kHz
50
kΩ
pF
PCB Assembly, Soldering and Cleaning
Board-assembly production process and assembly quality
can affect the performance of the 32 KHz oscillator.
Depending on the flux material used, the soldering process
can leave critical residues on the PCB surface. High
humidity and fast temperature cycles that cause humidity
condensation on the printed circuit board can create
process residuals. These process residuals cause the
insulation of the sensitive oscillator signal lines towards
each other and neighboring signals on the PCB to decrease.
High humidity can lead to moisture condensation on the
surface of the PCB and, together with process residuals,
reduce the surface resistivity of the board. Flux residuals on
the board can cause leakage current paths, especially in
humid environments. Thorough PCB cleaning is therefore
highly recommended in order to achieve maximum
performance by removing flux residuals from the board after
assembly. In general, reduction of losses in the oscillator
circuit leads to better safety margin and reliability.
7
PCB Design Consideration
•
Signal traces between IDT device pins and the crystal
must be kept as short as possible. This minimizes
parasitic capacitance and sensitivity to crosstalk and
EMI. Note that the trace capacitances play a role in the
effective crystal load capacitance calculation.
•
Data lines and frequently switching signal lines should be
routed as far away from the crystal connections as
possible. Crosstalk from these signals may disturb the
oscillator signal.
•
Reduce the parasitic capacitance between X1 and X2
signals by routing them as far apart as possible.
•
The oscillation loop current flows between the crystal and
the load capacitors. This signal path (crystal to CL1 to
CL2 to crystal) should be kept as short as possible and
ideally be symmetric. The ground connections for both
capacitors should be as close together as possible.
Never route the ground connection between the
capacitors all around the crystal, because this long
ground trace is sensitive to crosstalk and EMI.
•
To reduce the radiation / coupling from oscillator circuit,
an isolated ground island on the GND layer could be
made. This ground island can be connected at one point
IDT™
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
4
IDT1337
REV H 120208
IDT1337
REA LTIME CLOCK WITH SERIAL INTERFACE
RTC
Address Map
Table 2 (Timekeeper Registers) shows the address map for the IDT1337 registers. During a multibyte access, when the
address pointer reaches the end of the register space (0Fh), it wraps around to location 00h. On an I
2
C START, STOP, or
address pointer incrementing to location 00h, the current time is transferred to a second set of registers. The time
information is read from these secondary registers, while the clock may continue to run. This eliminates the need to re-read
the registers in case of an update of the main registers during a read.
Table 1. Timekeeper Registers
Address
00h
01h
02h
03h
04h
05h
06h
07h
08h
A1M1
A1M2
Bit 7
0
0
0
0
0
Century
12/24
0
0
0
10 year
10 seconds
10 minutes
AM/PM
09h
A1M3
12/24
10 hour
10 hour
Hour
Day,
Date
Minutes
Alarm 1 Hours
Alarm 1 Day
Alarm 1 Date
Alarm 2
Minutes
Alarm 2 Hours
Alarm 2 Day
Alarm 2 Date
A2IE
A2F
A1IE
A1F
Control
Status
0
Bit 6
Bit 5
10 seconds
10 minutes
AM/PM
10 hour
0
10 date
10 month
10 hour
0
0
Date
Month
Year
Seconds
Minutes
Hour
Day
Hours
Day
Date
Month/Century
Year
Alarm 1
Seconds
Alarm 1
Minutes
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Function
Seconds
Minutes
Range
00 - 59
00 - 59
1 - 12 +
AM/PM
00 - 23
1-7
01 - 31
01 - 12 +
Century
00 - 99
00 - 59
00 - 59
1 - 12 +
AM/PM
00 - 23
1-7
1 - 31
00 - 59
1 - 12 +
AM/PM
00 - 23
1-7
1 - 31
Seconds
Minutes
0Ah
0Bh
A1M4
A2M2
DY/DT
10 date
10 minutes
AM/PM
0Ch
A2M3
12/24
10 hour
10 hour
Hour
Day,
Date
RS1
0
INTCN
0
0Dh
0Eh
0Fh
A2M4
EOSC
OSF
DY/DT
0
0
0
0
10 date
RS2
0
Note:
Unless otherwise specified, the state of the registers are not defined when power is first applied or when VCC falls below the
V
CCT
min
IDT™
REAL-TIME CLOCK WITH I
2
C SERIAL INTERFACE
5
IDT1337
REV H 120208
模拟与混合信号
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
