REVISIONS
LTR
D
DESCRIPTION
Add vendor CAGE F8859. Add device class V criteria. Editorial changes
throughout. - jak
Correct data limits in paragraph 1.3 and I
IN
test conditions in table I. Add case
outline X. Add table III, delta limits. Editorial changes throughout. - jak
Correct table II. Update boilerplate to MIL-PRF-38535 requirements. – jak
DATE (YR-MO-DA)
99-11-05
APPROVED
Monica L. Poelking
E
00-06-21
Monica L. Poelking
F
02-02-08
Thomas M. Hess
CURRENT CAGE CODE 67268
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
F
15
F
16
REV
SHEET
F
1
F
2
F
3
F
4
F
5
F
6
F
7
F
8
F
9
F
10
F
11
F
12
F
13
F
14
PREPARED BY
Greg A. Pitz
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
CHECKED BY
D. A. DiCenzo
APPROVED BY
Robert P. Evans
DRAWING APPROVAL DATE
84-10-17
REVISION LEVEL
F
MICROCIRCUIT, DIGITAL, HIGH-SPEED CMOS, OCTAL
TRANSPARENT D-TYPE LATCHES WITH THREE-
STATE OUTPUTS, MONOLITHIC SILICON
SIZE
CAGE CODE
A
SHEET
14933
1
OF
16
84072
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E206-02
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)
and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.
1.2 PIN. The PIN is as shown in the following examples.
84072
01
R
X
Drawing number
For device class V:
5962
-
Device type
(see 1.2.2)
Case outline
(see 1.2.4)
Lead finish
(see 1.2.5)
84072
01
V
X
X
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
\/
Drawing number
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
54HC373
Circuit function
Octal transparent D-type latches with
three-state outputs
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed
below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q
designators will not be included in the PIN and will not be marked on the device.
Device class
M
Q or V
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
R
S
X
2
Descriptive designator
GDIP1-T20 or CDIP2-T20
GDFP2-F20 or CDFP3-F20
See figure 1
CQCC1-N20
Terminals
20
20
20
20
Package style
Dual-in-line
Flat pack
Flat pack
Square leadless chip carrier
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
F
84072
SHEET
2
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A
for device class M.
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (V
CC
)..................................................................................
DC input voltage range (V
IN
)................................................................................
DC output voltage range (V
OUT
)...........................................................................
Input clamp current (I
IK
) (V
IN
< 0.0 or V
IN
> V
CC
) ..................................................
Output clamp current (I
OK
) (V
OUT
< 0.0 or V
OUT
> V
CC
).........................................
Continuous output current (I
OUT
) (V
OUT
= 0.0 to V
CC
) ...........................................
Continuous current through V
CC
or GND .............................................................
Storage temperature range (T
STG
).......................................................................
Maximum power dissipation (P
D
):........................................................................
Lead temperature (soldering, 10 seconds)..........................................................
Thermal resistance, junction-to-case (θ
JC
) ..........................................................
Junction temperature (T
J
) ....................................................................................
1.4 Recommended operating conditions. 2/ 3/
Supply voltage range (V
CC
)..................................................................................
Case operating temperature range (T
C
) .............................................................
Input rise or fall time t
r
, t
f
):
VCC = 2.0 V ......................................................................................................
VCC = 4.5 V ......................................................................................................
VCC = 6.0 V ......................................................................................................
Minimum setup time, data before LE↓ (t
s
):
T
C
= +25°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
T
C
= -55°C to +125°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
+2.0 V dc to +6.0 V dc
-55°C to +125°C
0 to 1,000 ns
0 to 500 ns
0 to 400 ns
-0.5 V dc to +7.0 V dc
-0.5 V dc to V
CC
+0.5 V dc
-0.5 V dc to V
CC
+0.5 V dc
±20
mA
±20
mA
±35
mA
±70
mA
-65°C to +150°C
500 mW 4/
+260°C
See MIL-STD-1835
+175°C 5/
100 ns
20 ns
17 ns
150 ns
30 ns
26 ns
1/
2/
3/
4/
5/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
Unless otherwise noted, all voltages are referenced to GND.
The limits for the parameters specified herein shall apply over the full specified V
CC
range and case temperature range of
-55°C to +125°C.
For T
C
= +100°C to +125°C, derate linearly at 12 mW/°C.
Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in
accordance with method 5004 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
F
84072
SHEET
3
Minimum hold time, data after LE↓ (t
h
):
T
C
= +25°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
T
C
= -55°C to +125°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
Minimum pulse width LE high (t
w
):
T
C
= +25°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
T
C
= -55°C to +125°C:
V
CC
= 2.0 V ........................................................................................................
V
CC
= 4.5 V ........................................................................................................
V
CC
= 6.0 V ........................................................................................................
2. APPLICABLE DOCUMENTS
50 ns
10 ns
10 ns
75 ns
15 ns
13 ns
100 ns
20 ns
17 ns
150 ns
30 ns
26 ns
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the
issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 -
MIL-STD-1835 -
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
F
84072
SHEET
4
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table. The truth table shall be as specified on figure 3.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 4.
3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified in figure 5.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking
for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or
for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
group number 36 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
F
84072
SHEET
5
stm32/stm8
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
