User’s Manual
DemoKit-KA1
Demonstration Kit for
NEC Electronics Low-Pin-Count Devices
Document No. U17680EU1V0UM00
©August
2005. NEC Electronics America, Inc.
All rights reserved.
The information in this document is current as of August 2005. The information is subject to change without notice.
For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-
to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please
check with an NEC sales representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without prior written consent of
NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property
rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other
liability arising from the use of such NEC Electronics products. No license, express, implied or otherwise, is granted
under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative purposes
in semiconductor product operation and application examples. The incorporation of these circuits, software and
information in the design of customer's equipment shall be done under the full responsibility of customer. NEC
Electronics no responsibility for any losses incurred by customers or third parties arising from the use of these circuits,
software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers
agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of
damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers
must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure
features.
NEC Electronics products are classified into the following three quality grades: “Standard”, “Special” and “Specific”.
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-designated
“quality assurance program” for a specific application. The recommended applications of NEC Electronics product
depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics
product before using it in a particular application.
"Standard":
Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots.
"Special":
Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support).
"Specific":
Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support
systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is “Standard” unless otherwise expressly specified in NEC Electronics
data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC
Electronics, they must contact NEC Electronics sales representative in advance to determine NEC Electronics 's
willingness to support a given application.
Notes:
1. "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
2. "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02.10
ii
DemoKit-KA1 User’s Manual
DemoKit-KA1 complies with the EMC protection requirements.
WARNING
This is “Class A” (EN 55022:1998) equipment. This equipment can cause radio frequency noise when used in the
residential area. In such cases, the user/operator of the equipment may be required to take appropriate countermeasures
under his responsibility.
EEDT-ST-001-11
CAUTION
This equipment should be handled like a CMOS semiconductor device. The user must take all precautions to avoid
build-up of static electricity while working with this equipment. All test and measurement tool including the workbench
must be grounded. The user/operator must be grounded using the wrist strap. The connectors and/or device pins should
not be touched with bare hands.
EEDT-ST-004-10
iii
Revision History
Date
August 2005
Revision
—
Section
—
Description
Initial release
iv
DemoKit-KA1 User’s Manual
Contents
1.
Introduction.....................................................................................................................................1
1.1
1.2
1.3
Features..................................................................................................................................................1
System Requirements ...........................................................................................................................2
Package Contents ..................................................................................................................................2
2.
System Configuration .....................................................................................................................3
2.1
2.2
2.3
DemoKit-KA1 ........................................................................................................................................3
Host Computer.......................................................................................................................................3
Power Supply .........................................................................................................................................3
3.
Board Components .........................................................................................................................4
3.1
SW3 Configuration Switch ...................................................................................................................4
3.1.1
Operating Mode Selection: SW3/S1.........................................................................................5
3.1.2
UART Selection: SW3/S2 ........................................................................................................5
3.1.3
SW3/S3: Clock Mode Selection ...............................................................................................5
3.1.4
SW3/S4: UART Mode Selection..............................................................................................5
3.2 SW1: User Button ..................................................................................................................................5
3.3 SW2: Start Button .................................................................................................................................5
3.4 CN7: USB Interface Connector ............................................................................................................6
3.5 Connector CN1 / Clock Configuration ................................................................................................6
3.6 CN2 and CN12: External Peripheral Configuration..........................................................................6
3.7 External Potentiometer R24 .................................................................................................................6
3.8 A/D Converter Reference Voltage Input .............................................................................................6
3.9 External LEDs D1–D4...........................................................................................................................7
3.10 External connectors CN3, CN4, CN5, and CN6.................................................................................8
4.
5.
Memory Map...................................................................................................................................9
Getting Started..............................................................................................................................10
5.1
5.2
Hardware Installation .........................................................................................................................10
Software installation............................................................................................................................10
5.2.1
SM+ (Product ID: 00001664C) ........................................................................................... 11
5.2.2
NEC Electronics Software Development Tools .....................................................................11
5.2.3
PG-LPC Flash Programming GUI..........................................................................................11
5.2.4
Sample Programs ................................................................................................................. 11
5.2.5
Driver................................................................................................................................... 12
5.2.5.1 Windows 98SE/ME Systems....................................................................................12
5.2.5.2 Windows 2000 Systems ...........................................................................................14
5.2.5.3 Windows XP Systems ..............................................................................................20
Confirmation of USB Driver Installation ..........................................................................................25
5.3.1
Windows 98SE/ME Systems ............................................................................................... 26
5.3.2
Windows 2000/XP Systems ................................................................................................ 26
Driver Uninstallation...........................................................................................................................27
5.3
5.4
6.
PG-LPC Flash Programming Software ....................................................................................... 29
6.1
6.2
6.3
Starting the Software GUI ..................................................................................................................29
Toolbar .................................................................................................................................................30
Menu Bar..............................................................................................................................................30
6.3.1
File Menu............................................................................................................................. 30
6.3.1.1 Load Command ..................................................................................................... 31
6.3.1.2 Quit Command ...................................................................................................... 31
6.3.2
Device Menu........................................................................................................................ 31
6.3.2.1 Blank Check Command......................................................................................... 32
v
嵌入式系统
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
