REVISIONS
LTR
C
D
E
F
G
H
J
DESCRIPTION
Change device type 05 to a synchro-resolver to digital converter.
Make changes to table I, figure 1, and 2.
Added device types 06 and 07. Added vendor CAGE S7631.
Redrew entire document.
Paragraph 1.2..2, device type 01, change synchro accuracy from ±1.3
to ±1.6 arc minutes. Changes in table I for device type 01.
Updated drawing to reflect the current requirements of MIL-PRF-
38534. -sld
Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add T
C
.
Table I, power supply current test, change the max limit from 30 mA
to 35 mA. -gz
Paragraph 1.3; Correct “Power Dissipation” (P
D
) for device types 01,
02, 06, and 07 from 210 mW to 245 mW, correct “Thermal resistance,
junction-to-case (θ
JC
)” from “8.0°C/W” to “10°C/W”, and delete
“Thermal resistance, junction-to-ambient (θ
JA
)” Table I; “Drive
Capability” test for “High impedance load” conditions for devices
types 01,02,06,07 correct min value from “-1.0” to “-10”, for “Input
current, INH, 14B” correct max value for device types 01,06,07 from
“-10” µA to “-30” µA, for “Input current, LBE, HBE” correct max value
for device types 01,06,07 from “25” µA to “30” µA” mA, add reference
to footnote “8/” to current test, add footnote “8/ Digital output loads will
add to supply current.” to end of Table I. Update drawing paragraphs.
-gc
DATE (YR-MO-DA)
95-06-09
97-06-25
00-08-02
03-06-03
04-06-18
08-06-16
13-02-06
APPROVED
K. A. Cottongim
K. A. Cottongim
Raymond Monnin
Raymond Monnin
Raymond Monnin
Robert M. Heber
Charles F. Saffle
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
J
15
REV
SHEET
J
1
J
2
J
3
J
4
J
5
J
6
J
7
J
8
J
9
J
10
J
11
J
12
J
13
J
14
PREPARED BY
Donald R. Osborne
CHECKED BY
Steve Duncan
STANDARD
MICROCIRCUIT
DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
APPROVED BY
William K. Heckman
MICROCIRCUIT, HYBRID, LINEAR,
11.8 VOLTS, SYNCHRO-RESOLVER TO
DIGITAL CONVERTER
DRAWING APPROVAL DATE
91-08-15
REVISION LEVEL
J
SIZE
A
SHEET
CAGE CODE
67268
1 OF
15
5962-90820
DSCC FORM 2233
APR 97
5962-E067-13
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
Federal
stock class
designator
\
-
RHA
designator
(see 1.2.1)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
04
05
06
07
Generic number
SD-14531D1-115
SDC14531-631
HSRD1006-C148/2
HRD1006-C148A/2
HSRD1056-C775B/2
SD-14531D1-114
SD-14531D1-112
Circuit function
11.8 V, 400 Hz, S-R/D converter
11.8 V, 400 Hz, R/D converter
11.8 V, 400 Hz, S-R/D converter
11.8 V, 400 Hz, R/D converter
11.8 V, 400 Hz, R/D converter
11.8 V, 400 Hz, S-R/D converter
11.8 V, 400 Hz, S-R/D converter
Accuracy
±1.3
arc minutes (resolver)
±1.6
arc minutes (synchro)
±1.3
arc minutes (resolver)
±1.3
arc minutes (resolver)
±2.6
arc minutes (synchro)
±1.3
arc minutes (resolver)
±1.3
arc minutes (resolver)
±2.6
arc minutes (synchro)
±2.6
arc minutes (synchro)
±5.2
arc minutes
(synchro/resolver)
90820
01
Device
type
(see 1.2.2)
/
H
Device
class
designator
(see 1.2.3)
X
Case
outline
(see 1.2.4)
X
Lead
finish
(see 1.2.5)
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
H
G
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-90820
SHEET
2
DSCC FORM 2234
APR 97
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
D
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Descriptive designator
See figure 1
Terminals
36
Package style
Dual-in-line
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Supply voltage (V
S
) ....................................................................
Reference input .........................................................................
Digital inputs ..............................................................................
Power dissipation (P
D
): 2/
Device types 01, 02, 06, and 07 .............................................
Device types 03 and 04 ..........................................................
Device type 05........................................................................
Storage temperature range........................................................
Lead temperature (soldering, 10 seconds) ................................
Thermal resistance, junction-to-case (θ
JC
).................................
Junction temperature (T
J
) ..........................................................
1.4 Recommended operating conditions.
Supply voltage (V
S
) ....................................................................
Ambient operating temperature range(T
A
) .................................
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
+4.5 V dc to +5.5 V dc
-55°C to +125°C
+7.0 V dc
150 V rms
-0.3 V dc to +7.0 V dc
245 mW
166 mW
110 mW
-65°C to +150°C
+300°C
10°C/W
+150°C
1/
2/
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
Power dissipation applies up to T
C
= +125°C.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-90820
SHEET
3
DSCC FORM 2234
APR 97
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Output accuracy test angles. The output accuracy test angles shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked
with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot
sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for
those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer
and be made available to the preparing activity (DLA Land and Maritime-VA) upon request.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-90820
SHEET
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55°C
≤
T
A
≤
+125°C
unless otherwise specified
Group A
subgroups
Device
types
Min
Limits
Max
Unit
Resolution control
RC
14B = logic "1"
14B = logic "0"
7,8
All
14
16
14
16
+1.0
Bits
Accuracy repeatability 2/
AR
7,8
01,02,
06,07
01,02,
03,04,
05
01
02,03,
04,05
-1.0
LSB
Output accuracy 3/
AOUT
16-bit resolution 4/
(resolver mode)
7,8
±1.3
ARC-MIN
16-bit resolution 4/
(synchro mode)
±1.6
±2.6
±2.6
14-bit resolution 4/
01,02,
03,04,
05
06
07
16-bit resolution 4/
(synchro/resolver mode)
±2.6
±5.2
-45
+45
Degree
Reference synthesizer 2/
RS
Reference phase shift
between the converter
signal and reference inputs
4,5,6
All
Reference input
Input voltage range 2/
V
IN
4,5,6
01,02,
06,07
03,04,
05
Carrier frequency 2/
4,5,6
All
4
130
V rms
20
130
360
1000
Hz
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-90820
SHEET
5
DSCC FORM 2234
APR 97
51单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
