Datasheet> 器件分类 > 无源元件> 电容器> C1206Q201F2GAL3325

文档预览

C1206Q201F2GAL3325: 产品描述Ceramic Capacitor, Multilayer, Ceramic, 200V, 1% +Tol, 1% -Tol, BP, -/+30ppm/Cel TC, 0.0002uF, 1206,; 产品类别无源元件电容器; 文件大小160KB，共8页; 制造商KEMET(基美); 官网地址http://www.kemet.com

下载文档详细参数全文预览

C1206Q201F2GAL3325概述

Ceramic Capacitor, Multilayer, Ceramic, 200V, 1% +Tol, 1% -Tol, BP, -/+30ppm/Cel TC, 0.0002uF, 1206,

C1206Q201F2GAL3325规格参数

参数名称	属性值
是否Rohs认证	不符合
Objectid	926573709
包装说明	, 1206
Reach Compliance Code	not_compliant
ECCN代码	EAR99
YTEOL	7.82
电容	0.0002 µF
电容器类型	CERAMIC CAPACITOR
介电材料	CERAMIC
高度	1.6 mm
JESD-609代码	e0
长度	3.07 mm
多层	Yes
负容差	1%
端子数量	2
最高工作温度	125 °C
最低工作温度	-55 °C
封装形式	SMT
包装方法	Bulk
正容差	1%
额定（直流）电压（URdc）	200 V
尺寸代码	1206
温度特性代码	BP
温度系数	30ppm/Cel ppm/°C
端子面层	Tin/Lead (Sn70Pb30) - with Nickel (Ni) barrier
宽度	1.52 mm

文档预览

下载PDF文档

全文
预览

CERAMIC HIGH RELIABILITY

GENERAL INFORMATION GR900 SERIES

HIGH RELIABILITY — GR900

GR900 capacitors are intended for use in any application where

the chance of failure must be reduced to the lowest possible

level. While any well-made multilayer ceramic capacitor is an

inherently reliable device, GR900 capacitors receive special

attention in all phases of manufacture including:

— Raw Materials Selection

— Special Designs

— Clean Room Production

— Individual Batch Testing

— C-SAM (when applicable)

— Singular Batch Identity is Maintained

— Destructive Physical Analysis

These parts are well worth the added investment in comparison

to the cost of a device or system failure.

Typical applications include:

Medical, Aerospace, Communication Satellites, Radar, Guidance

Systems.

SCREENING AND SAMPLE TESTS

Each batch receives the following testing/inspections:

Preliminary:

1. Destructive Physical Analysis: (DPA) - A sample is pulled from

each lot and examined per EIA-469 and KEMET’s strict internal

void and delamination criteria. Sampling plan is per MIL-PRF-123.

2. C-SAM - May be performed on batches failing to meet the

DPA criteria for removal of marginal product. Not required on

each lot.

Group A

1. Thermal Shock

— Materials used in the construction of mul-

tilayer ceramic capacitors possess various thermal coefficients of

expansion. To assure maximum uniformity, each part is temper-

ature cycled in accordance to MIL-STD-202, Method 107,

Condition A with Step 3 being 125°C. Number of cycles shall be

20 (100% of lot).

2. Voltage Conditioning

— One of the most strenuous environ-

ments for any capacitor is the high temperature/high voltage test.

All units are subject to twice-rated voltage to the units at the max-

imum rated temperature of 125°C for a minimum of 168 hours

and a maximum of 264 hours. The voltage conditioning may be

terminated at any time during 168 hours to 264 hours time inter-

val that confirmed failures meet the requirements of the PDA dur-

ing the last 48 hours of 1 unit or .4% (100% of lot).

Optional Voltage Conditioning (Accelerated Voltage

Conditioning)

— All conditions of the standard voltage condi-

tioning apply with the exception of increased voltage and

decreased test time. Refer to MIL-PRF-123 for the proper formula.

*Step 5 is performed on chips at this point (100% of lot).

3. Dielectric Withstanding Voltage

— 250% of the dc rated volt-

age at 25°C (100% of lot).

4. Insulation Resistance

— The 25°C measurement with rated

voltage applied shall be the lesser of 100 GΩ or 1000 megohm-

microfarads (100% of lot).

*5. Insulation Resistance

— The 125°C measurement with

rated voltage applied shall be the lesser of 10 GΩ or 100

megohm-microfarads (100% of lot). For chips, 125°C IR is per-

formed prior to Step 3 above.

6. Storage

at 150°C for 2 hours minimum without voltage applied

followed by a 12-hour minimum stabilization period (temperature

characteristic BX only).

7. Capacitance

— Shall be within specified tolerance at 25°C

(100% of lot). (Aging phenomenon is taken into account for BX

dielectric to obtain capacitance.)

8. Dissipation Factor

— Shall not exceed 2.5% for X7R (BX)

dielectric, 0.15% for C0G (BP) dielectric at 25°C. (100% of lot.)

9. Percent Defective Allowable (PDA)

— The overall PDA is 8%

for parts outside the MIL-PRF-123 values. The PDA is per MIL-

PRF-123 for all parts that are valid MIL-PRF-123 values. The PD

includes steps 1 through 8 above with the following exceptions.

Capacitance exclusion - capacitance values no more than 5% or

.5pF, whichever is greater for BX characteristic or 1% or .3pF,

whichever is greater for BP characteristic beyond specified toler-

ance limit, shall be removed from the lot but shall not be consid-

ered defective for determination of the PD.

Insulation Resistance at 25°C — Product which is not acceptable

for twice the military limit but is acceptable per the military limit,

is removed from the lot but shall not be considered defective for

determination of the PD.

10. Visual and Mechanical Examination

— Performed per MIL-

PRF-123 criteria.

11. Radiographic Examination (Leaded Devices Only)

—

Radial devices receive a one-plane X-ray.

12. Destructive Physical Analysis (DPA)

— A sample is exam-

ined on each lot per EIA-469. Sampling Plan is per MIL-PRF-123.

STANDARD PACKAGING

All products are packaged in trays except C512 capacitors which

are packaged 1 piece per bag.

DATA PACKAGE

A data package is sent with each shipment which contains:

Final Destructive Physical Analysis (DPA) report.

Certificate of Compliance stating that the parts meet all applic-

able requirements of the appropriate military specification to the

best failure level to which KEMET is approved.

Summary of Group A Testing.

推荐资源

电子名片(vCard)传输: 为什么手机的vCard的格式与电脑outlook生成的vCard格式不一样？而用开源库libmimedir解析vCard文件时也有问题。谢谢...; lhjs 嵌入式系统

完全没学过电学公司要求我去自学画PCB板请问该从何学起？: 本人没有任何学习电子电路经验！ ...; 爱吃萝卜的图纸 PCB设计

基于MSP430F147的智能金属浮子流量计设计: 希望对大家有用！14405...; 小艾测试/测量

电池的损伤机理与故障预警: 摘要：电池损伤理论比电池老化理论更适用于电池故障的分析研究。研究了在电池组中微损伤的成因。分析了电池组中损伤叠加直至“断裂型”失效的过程，得出现有电池安全体系存在系统性隐患的重要 ......; feifei 嵌入式系统

51单片机C语言程序求助: 各位大虾，我是一名51单片机的初学者，最近自己学着写了一个响应外部中断，按键延时去抖的程序，但是在编译的时候总是报错，请帮忙解决，O(∩_∩)O谢谢！附件是我的截屏，请帮我看看。...; mhkeil51 51单片机

运放偏置电路和偏置电流: 晶体管构成的放大器要做到不失真地将信号电压放大，就必须保证晶体管的发射结正偏、集电结反偏。即应该设置它的工作点。所谓工作点就是通过外部电路的设置使晶体管的基极、发射极和集电极处 ......; qwqwqw2088 模拟与混合信号

器件捷径: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

热门器件

开源项目推荐更多

热门活动更多

热门文章更多

技术资料推荐更多