CALIFORNIA MICRO DEVICES
CM8870/70C
CMOS Integrated DTMF Receiver
Features
• Full DTMF receiver
• Less than 35mW power consumption
• Industrial temperature range
• Uses quartz crystal or ceramic resonators
• Adjustable acquisition and release times
• 18-pin DIP, 18-pin DIP EIAJ, 18-pin SOIC, 20-pin
PLCC
•
CM8870C
—
—
—
Power down mode
Inhibit mode
Buffered OSC3 output (PLCC package only)
Applications
• PABX
• Central office
• Mobile radio
• Remote control
• Remote data entry
• Call limiting
• Telephone answering systems
• Paging systems
• CM8870C is fully compatible with CM8870 for 18-pin
devices by grounding pins 5 and 6
Product Description
The CAMD CM8870/70C provides full DTMF receiver capability by integrating both the bandsplit filter and digital
decoder functions into a single 18-pin DIP, SOIC, or 20-pin PLCC package. The CM8870/70C is manufactured using
state-of-the-art CMOS process technology for low power consumption (35mW, max.) and precise data handling. The
filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The
CM8870/70C decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a
4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-
fier, clock generator, and a latched three-state interface bus. The on-chip clock generator requires only a low cost TV
crystal or ceramic resonator as an external component.
© 2000 California Micro Devices Corp. All rights reserved.
9/28/2000
+ ## '
Tel: (408) 263-3214
Fax: (408) 263-7846
www.calmicro.com
215 Topaz Street, Milpitas, California 95035
1
CALIFORNIA MICRO DEVICES
Absolute Maximum Ratings:
(Note 1)
ABSOLUTE MAXIMUM RATINGS
Parameter
Power Supply Voltage (V
DD
-
V
SS
)
Voltage on any Pin
Current on any Pin
Operating Temperature
Storage Temperature
Symbol
V
DD
Vdc
I
D D
T
A
T
S
Value
6.0V Max
V
SS
-0.3V to V
DD
+0.3V
10mA Max
-40°C to +85°C
-65°C to +150°C
CM8870/70C
This device contains input protection
against damage due to high static
voltages or electric fields; however,
precautions should be taken to avoid
application of voltages higher than the
maximum rating.
Notes:
1. Exceeding these ratings may cause
permanent damage, functional
operation under these conditions is
not implied.
DC Characteristics:
All voltages referenced to V
SS
, V
DD
= 5.0V ± 5%, T
A
= -40°C to +85°C unless otherwise noted.
Parameter
Operating Supply Voltage
Operating Supply Current
Standby Supply Current
Power Consumption
Low Level Input Voltage
High Level Input Voltage
Input Leakage Current
Pull Up (Source) Current on TOE
Input Impedance, (IN+, IN-)
Steering Threshold Voltage
Low Level Output Voltage
High Level Output Voltage
Output Low (Sink) Current
Output High (Source) Current
Output Voltage
Output Resistance
DC CHARACTE RISTICS
Symbol
Min
Typ
V
DD
I
DD
I
DDQ
P
O
V
IL
V
IH
I
I H
/ L
I L
I
so
R
IN
V
Tst
V
OL
V
OH
I
OL
I
OH
V
R EF
R
OR
4.97
1.0
0.4
2.4
10
2.5
0.8
2.7
8
2.2
3.5
0.1
6.5
10
2.5
0.03
20
15
4.75
3.0
Max
5.25
7.0
25
35
1.5
Units
V
mA
µA
mW
V
V
µA
µA
MΩ
V
V
V
mA
mA
V
ΚΩ
PD =V
DD
f=3.579 MHz; V
DD
=5.0V
V
DD
=5.0V
V
DD
=5.0V
V
IN
= V
SS
= V
DD
(Note 1)
TOE=0V, V
DD
=5.0V
@ 1K H z
V
DD
= 5.0V
V
DD
= 5.0V, No Load
V
DD
= 5.0V, No Load
V
OUT
= 0.4V
V
OUT
= 4.6V
V
DD
= 5.0V, No Load
Test Conditions
V
REF
Operating Characteristics:
All voltages referenced to V
SS
, V
DD
= 5.0V ± 5%, T
A
= -40°C to +85°C unless otherwise noted.
Gain Setting Amplifier
OPERATING CHARACTERISTICS
Parameter
Input Leakage Current
Input Resistance
Input Offset Voltage
Power Supply Rejection
Common Mode Rejection
D C Open Loop Voltage Gain
Open Loop Unity Gain Bandwidth
Output Voltage Swing
Maximum Capacitive Load (GS)
Maximum Resistive Load (GS)
Common Mode Range (No Load)
©2000 California Micro Devices Corp. All rights reserved.
Symbol
I
IN
R
IN
V
OS
PSRR
CMR R
A
V OL
fc
V
O
C
L
R
L
Vcm
Min
10
Typ
Max
±100
±25
Units
nA
MΩ
mV
dB
dB
dB
MHz
V
P-P
Test Conditions
V
S S
< V
IN
< V
D D
50
40
32
0.3
4.0
10 0
50
2.5
1KHz (Note 12)
-3.0V < VI
N
< 3.0V
R
L
≥
100KW to V
SS
pF
KΩ
V
P-P
N o L o ad
2
215 Topaz Street, Milpitas, California 95035
Tel: (408) 263-3214
Fax: (408) 263-7846
www.calmicro.com
9/28/2000
CALIFORNIA MICRO DEVICES
CM8870/70C
AC Characteristics:
All voltages referenced to V
SS
, V
DD
=5.0V ±5%, T
A
=-40°C to +85°C, f
CLK
=3.579545 MHz using
test circuit (Fig. 1) unless otherwise noted.
AC CHARACTERISTICS
Parameter
Valid Input Signal Levels
(each tone of composite signal)
Positive Twist Accept
Negative Twist Accept
Freq. D eviation Accept Limit
Freq. D eviation Reject Limit
Third Tone Tolerance
Noise Tolerance
D ial Tone Tolerance
Tone Present D etection Time
Tone Absent D etection Time
Min Tone D uration Accept
Max Tone D uration Reject
Min. Interdigit Pause Accept
Max. Interdigit Pause Reject
Propagation D elay (St to Q)
Propagation D elay (St to StD )
Output D ata Set Up (Q to StD )
Propagation D elay (TOE to Q)
Crystal/Clock Frequency
Clock Output (OSC 2)
Capacitive
L o ad
Enable
D isable
t
DP
t
DA
t
R EC
t
R EC
t
ID
t
DO
t
PQ
t
PS
t
D
t
QS
t
D
t
PTE
t
PTD
f
CL K
C
LO
3.5759
20
6
9
3.4
50
300
3.5795
3.5831
30
11
16
20
40
5
0.5
±3.5%
-16
-12
+22
8
3
14
8.5
40
Symbol
Min
-29
27.5
Typ
Max
+1
869
10
10
1.5%±2Hz
Units
dBm
mV
RMS
dB
dB
Nom.
Nom.
dB
dB
dB
mS
mS
mS
mS
mS
µS
µS
µS
µS
nS
nS
MHz
pF
Notes
1,2,3,4,5,8
2,3,4,8
2,3,5,8,10
2,3,5
2,3,4,5,8,9,13,14
2,3,4,5,6,8,9
2,3,4,5,7,8,9
Refer to
Timing D iagram
(User Adjustable)
Times shown are
obtained with
circuit in Fig. 1)
TOE = V
DD
R
L
= 10 K
Ω
C
L
= 50pF
Notes:
1.
dBm = decibels above or below a reference power
of 1 mW into a 600 ohm load.
2.
Digit sequence consists of all 16 DTMF tones.
3.
Tone duration = 40mS. Tone pause = 40 mS.
4.
Nominal DTMF frequencies are used.
5.
Both tones in the composite signal have
an equal amplitude.
6.
Bandwidth limited (0 to 3 KHz) Gaussian Noise.
7.
The precise dial tone frequencies are
(350 Hz and 440 Hz) ±2%.
8.
For an error rate of better than 1 in 10,000
9.
10.
11.
12.
13.
14.
Referenced to lowest level frequency component
in DTMF signal.
Minimum signal acceptance level is measured with
specified maximum frequency deviation.
Input pins defined as IN+, IN-, and TOE.
External voltage source used to bias V
REF
.
This parameter also applies to a third tone injected onto
the power supply.
Referenced to Figure 1. Input DTMF tone level
at -28 dBm.
© 2000 California Micro Devices Corp. All rights reserved.
9/28/2000
215 Topaz Street, Milpitas, California 95035
Tel: (408) 263-3214
Fax: (408) 263-7846
www.calmicro.com
3
CALIFORNIA MICRO DEVICES
CM8870/70C
Explanation of Events
A) Tone bursts detected, tone duration invalid, outputs not
updated.
B) Tone #n detected, tone duration valid, tone decoded
and latched in outputs.
C) End of tone #n detected, tone absent duration valid,
outputs remain latched until next valid tone.
D) Outputs switched to high impedance state.
E) Tone #n + 1 detected, tone duration valid, tone decoded
and latched in outputs (currently high impedance).
F) Acceptable dropout of tone #n + 1, tone absent duration
invalid, outputs remain latched.
G) End of tone #n + 1 detected, tone absent duration valid,
outputs remain latched until next valid tone.
Explanation of Symbols
V
IN
ESt
St/GT
DTMF composite input signal.
Early Steering Output. Indicates detection
of valid tone frequencies.
Steering input/guard time output. Drives
external RC timing circuit.
Q1-Q4 4-bit decoded tone output.
StD
Delayed Steering Output. Indicates that
valid frequencies have been present/absent
for the required guard time, thus constituting
a valid signal.
TOE
Tone Output Enable (input). A low level
shifts Q1-Q4 to its high impedance state.
t
REC
Maximum DTMF signal duration not
detected as valid.
t
REC
Minimum DTMF signal duration required
for valid recognition.
t
ID
Minimum time between valid DTMF signals.
t
DO
Maximum allowable drop-out during valid
DTMF signal.
t
DP
Time to detect the presence of valid
DTMF signals.
t
DA
Time to detect the absence of valid
DTMF signals.
t
GTP
Guard time, tone present.
t
GTA
Guard time, tone absent.
©2000 California Micro Devices Corp. All rights reserved.
4
215 Topaz Street, Milpitas, California 95035
Tel: (408) 263-3214
Fax: (408) 263-7846
www.calmicro.com
9/28/2000
CALIFORNIA MICRO DEVICES
Functional Description
The CAMD CM8870/70C DTMF Integrated Receiver provides
the design engineer with not only low power consumption, but
high performance in a small 18-pin DIP, SOIC, or 20-pin PLCC
package configuration. The CM8870/70C’s internal architec-
ture consists of a bandsplit filter section which separates the
high and low tones of the received pair, followed by a digital
decode (counting) section which verifies both the frequency
and duration of the received tones before passing the result-
ant 4-bit code to the output bus.
CM8870/70C
considered a valid pause. This capability together with the
capability of selecting the steering time constants externally,
allows the designer to tailor performance to meet a wide
variety of system requirements.
Guard Time Adjustment
In situations which do not require independent selection of
receive and pause, the simple steering circuit of Figure 4 is
applicable. Component values are chosen according to the
following formula:
t
REC
= t
DP
+ t
GTP
t
GTP
» 0.67 RC
The value of t
DP
is a parameter of the device and t
REC
is the
minimum signal duration to be recognized by the receiver. A
value for C of 0.1 uF is recommended for most applications,
leaving R to be selected by the designer. For example, a
suitable value of R for a t
REC
of 40 milliseconds would be 300K.
A typical circuit using this steering configuration is shown in
Figure 1. The timing requirements for most telecommunica-
tion applications are satisfied with this circuit. Different
steering arrangements may be used to select independently
the guardtimes for tone-present (t
GTP
) and tone absent (t
GTA
).
This may be necessary to meet system specifications which
place both accept and reject limits on both tone duration and
interdigit pause.
Guard time adjustment also allows the designer to tailor
system parameters such as talk-off and noise immunity.
Increasing t
REC
improves talk-off performance, since it reduces
the probability that tones simulated by speech will maintain
signal condition for long enough to be registered. On the
other hand, a relatively short t
REC
with a long t
DO
would be
appropriate for extremely noisy environments where fast
acquisition time and immunity to drop-outs would be require-
ments. Design information for guard time adjustment is shown
in Figure 5.
Filter Section
Separation of the low-group and high-group tones is achieved
by applying the dual-tone signal to the inputs of two 9
th
-order
switched capacitor bandpass filters. The bandwidths of these
filters correspond to the bands enclosing the low-group and
high-group tones (See Figure 3). The filter section also
incorporates notches at 350 Hz and 440 Hz which provides
excellent dial tone rejection. Each filter output is followed by a
single order switched capacitor section which smooths the
signals prior to limiting. Signal limiting is performed by high-
gain comparators. These comparators are provided with a
hysteresis to prevent detection of unwanted low-level signals
and noise. The outputs of the comparators provide full-rail
logic swings at the frequencies of the incoming tones.
Decoder Section
The CM8870/70C decoder uses a digital counting technique
to determine the frequencies of the limited tones and to verify
that these tones correspond to standard DTMF frequencies.
A complex averaging algorithm is used to protect against tone
simulation by extraneous signals (such as voice) while
providing tolerance to small frequency variations. The
averaging algorithm has been developed to ensure an
optimum combination of immunity to “talk-off” and tolerance to
the presence of interfering signals (third tones) and noise.
When the detector recognizes the simultaneous presence of
two valid tones (known as “signal condition”), it raises the
“Early Steering” flag (ESt). Any subsequent loss of signal
condition will cause ESt to fall.
Input Configuration
The input arrangement of the CM8870/70C provides a
differential input operational amplifier as well as a bias source
(V
REF
) which is used to bias the inputs at mid-rail.
Provision is made for connection of a feedback resistor to the
op-amp output (GS) for adjustment of gain.
In a single-ended configuration, the input pins are connected
as shown in Figure 1, with the op-amp connected for unity
gain and VREF biasing the input at ½ V
DD
. Figure 6 shows the
differential configuration, which permits the adjustment of gain
with the feedback resistor R5.
Steering Circuit
Before the registration of a decoded tone pair, the receiver
checks for a valid signal duration (referred to as “character-
recognition-condition”). This check is performed by an
external RC time constant driven by E
St
. A logic high on ESt
causes V
C
(See Figure 4) to rise as the capacitor discharges.
Providing signal condition is maintained (ESt remains high) for
the validation period (t
GTP
), V
C
reaches the threshold (V
TSt
) of
the steering logic to register the tone pair, thus latching its
corresponding 4-bit code (See Figure 2) into the output latch.
At this point, the GT output is activated and drives VC to V
DD
.
GT continues to drive high as long as ESt remains high,
signaling that a received tone pair has been registered. The
contents of the output latch are made available on the 4-bit
output bus by raising the three-state control input (TOE) to a
logic high. The steering circuit works in reverse to validate the
interdigit pause between signals. Thus, as well as rejecting
signals too short to be considered valid, the receiver will
tolerate signal interruptions (drop outs) too short to be
© 2000 California Micro Devices Corp. All rights reserved.
9/28/2000
Clock Circuit
The internal clock circuit is completed with the addition of a
standard television color burst crystal or ceramic resonator
having a resonant frequency of 3.579545 MHz. The
CM8870C in a PLCC package has a buffered oscillator output
(OSC3) that can be used to drive clock inputs of other devices
such as a microprocessor or other CM887X’s as shown in
Figure 7. Multiple CM8870/70Cs can be connected as shown
in figure 8 such that only one crystal or resonator is required.
215 Topaz Street, Milpitas, California 95035
Tel: (408) 263-3214
Fax: (408) 263-7846
www.calmicro.com
5
无线连接
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
