FP series
Fully illuminated pushbutton switches - momentary or latching
Distinctive features and specifications
K
Suited for integrated designs
K
Large but lightweight
K
Pad printed or laser etched symbols
K
Full actuator or symbol illumination, adaptable to design
requirements
Pad printing
Laser
Non-illuminated
Illuminated
ELECTRICAL SPECIFICATIONS
MATERIALS
• Max. current/voltage rating with resistive load : 200mA 12VDC
• Initial contact resistance : 50 mΩ max.
• Insulation resistance : 1 GΩ min. at 500VDC
• Dielectric strength : 1.000 Vrms 50 Hz min.
• Electrical life at full load : 300.000 cycles
GENERAL SPECIFICATIONS
• Case : stanyl PA46
• Actuator : PA12
• Bushing/ bezel : PA66
• Contacts : silver, gold plated
(code 4)
• Multi-wire lead AWG22
• Terminal seal : epoxy or termelt
overmolding
• Panel thickness : 1(.039) to 18 mm (.708) max.
• Total travel : 2,8 mm
± 0,5 mm
• Typical operating force : 8N
± 2N
• Mechanical life : 1 million cycles
• Torque : 3 Nm max. applied to nut
• Operating temperature : -40°C to +75°C
Dimensions
: first dimensions are in mm while inches are shown as bracketted numbers.
Tolerance
: The general tolerance for dimensions in this brochure is ± 0,3 (.012).
Dimensions, specifications and data shown in this brochure are subject to change without notice.
2
www.apem.com
APEM
FP series
Fully illuminated pushbutton switches - momentary or latching
Overview
FP
SERIES
Actuator
Model
P
R
Round, flat
Round, curved
Electrical function
1
3
OFF - ON
Normally open
(NO)
1
2
3
Terminals
Solder lugs
Straight cable
Right angle
cable, length
300 mm
A
Threaded bushing,
dia. 24 mm
LED control and No of poles
A
B
C
D
Non-illuminated, 1 pole
Non-illuminated, 2 poles
Independent, 1 pole
Independent, 2 poles
Contact mat.
4
Silver, gold
plated
1
2
3
4
5
6
7
9
A
B
Actuator colour
Blue
Black
Green
Grey
Yellow
Red
White/natural
Orange
Maroon
Black lacquered
1
2
3
4
5
6
7
Bezel colour
Blue
Black
Green
Grey
Yellow
Red
White/natural
X
A
B
C
D
E
F
G
LED colour
Non-illum.
Blue
Green
Red
Yellow
White
Red/green
Red/blue
0
1
2
3
LED resistor
No resistor
supplied
12V resistor
24V resistor
48V resistor
Symbols
See end of series
Silver on request.
Marking
X
1
2
No marking
Pad printing
Laser
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions :
first dimensions are in mm while inches are shown as bracketted numbers.
: please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
NOTICE
Mounting accessories
: Standard hardware supplied : 1 hex nut and 1 O-Ring
Packaging unit
: solder lug versions : 20 pieces - cable versions : 1 piece
APEM
www.apem.com
3
FP series
Fully illuminated pushbutton switches - momentary or latching
Mounting by Ø 24 mm threaded bushing
• Three terminal types
• Curved or flat actuator
To order a product, replace • with one of the codes selected under “LED control
and number of poles” on next page, then add he desired options.
MODEL
STRUCTURE
Solder lug terminals
LATCHING
Curved actuator
FPAR1•1
Flat actuator
FPAP1•1
MOMENTARY
(
NO
)
Curved actuator
FPAR3•1
Flat actuator
FPAP3•1
OFF
OFF
-
ON
ON
Straight cable terminals
LATCHING
Curved actuator
FPAR1•2
Flat actuator
FPAP1•2
MOMENTARY
(
NO
)
Curved actuator
FPAR3•2
Flat actuator
FPAP3•2
OFF
OFF
-
ON
ON
Right angle cable terminals
LATCHING
Curved actuator
FPAR1•3
Flat actuator
FPAP1•3
MOMENTARY
(
NO
)
OFF
OFF
-
ON
ON
Curved actuator
FPAR3•3
Flat actuator
FPAP3•3
4
www.apem.com
APEM
FP series
Fully illuminated pushbutton switches - momentary or latching
Options
LED CONTROL AND NUMBER OF POLES
Complete the model numbers on previous pages with one of the following codes.
Function 1 (latching)
Non-illuminated
one pole
A
Non-illuminated
two poles
B
Function 3 (momentary)
Independent
one pole
C
Independent
two poles
D
Function 1 (latching)
Function 3 (momentary)
CONTACT MATERIALS
4
Silver, gold plated
Silver : on request.
ACTUATOR COLOUR
1
: blue -
2
: black -
3
: green -
4
: grey -
5
: yellow -
6
: red -
7
: white/natural
9
: orange -
A
: maroon -
B
: black,
lacquered
BEZEL COLOUR
1
: blue -
2
: black -
3
: green -
4
: grey -
5
: yellow
6
: red -
7
: white/natural -
8
: bright chrome
LED COLOUR
X
: non-illuminated
A
: blue -
B
: green -
C
: red -
D
: yellow -
E
: white -
F
: red/green -
G
: red/blue
APEM
www.apem.com
5
FP series
Fully illuminated pushbutton switches - momentary or latching
Options
LED RESISTOR
0
1
2
3
No resistor supplied
12V resistor
24V resistor
48V resistor
MARKING
X
1
2
No marking
Pad printing
Laser
SYMBOLS
XX
No symbol
Available symbols
See following pages.
Marking colour
White marking for illuminated actuators (laser etching) and non-illuminated
black actuators (pad printing). Black marking for non-illuminated colour
actuators (pad printing). Other : on request.
Marking area
The symbol will be included in the hatched area.
6
www.apem.com
APEM
电子竞赛
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
