INCH-POUND
MIL-PRF-39014/1G
16 September 1997
SUPERSEDING
MIL-C-39014/1F
13 January 1993
PERFORMANCE SPECIFICATION SHEET
CAPACITORS, FIXED, CERAMIC DIELECTRIC
(GENERAL PURPOSE),
ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY,
STYLE CKR05, NATO TYPE DESIGNATION NCC61
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification and MIL-PRF-39014.
Inches
.015
.026
.045
.090
.100
.190
.200
1.250
mm
0.38
0.66
1.14
2.29
2.54
4.83
5.08
31.75
FIGURE 1. Dimensions and configurations.
AMSC N/A
1 of 8
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FSC 5910
MIL-PRF-39014/1G
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, tolerance is ± .010 inch (0.25 mm).
4. Lead length may be a minimum of .625 inch (15.88 mm) for use in tape and reel automatic insertion
equipment, when specified.
5. Lead diameter shall be .023 inch (0.58 mm) to .029 inch (0.74 mm).
6. Optional standoffs shall be of triangular shape so that the standoff will provide line contact with the surface
upon which the capacitor is mounted.
7. Thickness of standoffs shall be .075 inch (1.90 mm) to the body thickness.
8. Insulation coating shall not extend more than .018 inch (0.46 mm) along lead wires. For capacitors with
standoffs, insulation coating shall be measured from the plane from which the standoff height is measured.
9. At the option of the user, the standoff configuration may be substituted as a replacement for the nonstandoff
configuration of the same style.
10. For flush mounting .078 inch (1.98 mm), printed circuit hole diameter is required to clear shoulder.
FIGURE 1. Dimensions and configurations - Continued.
REQUIREMENTS:
Dimensions and configuration: See figure 1.
Case type: Molded or performed.
Capacitance value: See table I.
Capacitance tolerance: See table I.
Operating temperature range: -55°C to +125°C.
Voltage rating: See table I.
Radiographic inspection (failure rate level 'S’): In accordance with MIL-PRF-39014.
Dissipation factor: Not more than 2.5 percent.
Dielectric withstanding voltage:
Body insulation: Shall be able to withstand 1,300 volts between leads and case.
Insulation resistance (IR):
At 25°C: Not less than 100,000 megohms or 1,000 megohm-microfarads whichever is less.
At 125°C: Not less than 10,000 megohms or 100 megohm-microfarads whichever is less.
Voltage-temperature limits: In accordance with MIL-PRF-39014.
Capacitance change with reference to 25°C
Step A through step D of MIL-PRF- 39014,
voltage-temperature limit cycle table
Bias = 0 volt
±15 percent
Step E through step G of MIL-PRF-39014,
voltage-temperature limit cycle table
Bias = rated voltage
+15 percent, -25 percent
2
MIL-PRF-39014/1G
Immersion:
IR: Not less than 50 percent of initial 25°C requirement.
Salt spray (corrosion): Not applicable.
Life:
Rated conditions, 100 percent of dc rated voltage at 125°C.
0 hour through 3,000 hours:
IR: At 25°C, not less than 50 percent of initial 25°C requirement.
At 125°C, not less than 50 percent of initial 125°C requirement.
∆C:
±20 percent from initial measured value.
Dissipation factor: Not greater than 2.5 percent.
4,000 hours through 32,000 hours:
IR: At 25°C, not less than 15 percent of initial 25°C requirement.
At 125°C, not less than 15 percent of initial 125°C requirement.
∆C:
±20 percent from initial measured value.
Dissipation factor: Not greater than 2.5 percent.
Accelerated conditions, 200 percent of dc rated voltage at 125°C.
0 hour and 250 hours:
IR: At 25°C, not less than 50 percent of initial 25°C requirement.
At 125°C, not less than 50 percent of initial 125°C requirement.
∆C:
±20 percent from initial measured value.
Dissipation factor: Not greater than 2.5 percent.
1,000 hours, 2,000 hours, and 4,000 hours:
IR: At 25°C, not less than 15 percent of initial 25°C requirement.
At 125°C, not less than 15 percent of initial 125°C requirement.
∆C:
±20 percent from initial measured value.
Dissipation factor: Not greater than 2.5 percent.
Resistance to soldering heat: Resistance to soldering heat shall be in accordance with method 210 of MIL-STD-
202, test condition D. The immersion depth for capacitors with standoffs shall be .024 inch (0.61 mm) minimum.
∆C:
+15 percent, -5 percent of the initial 25°C measurement.
Solderability: The leads shall be solderable up to .020 inch (0.51 mm) from the body egress. For styles with
standoffs, solderability shall be measured from the plane shown on figure 1.
3
MIL-PRF-39014/1G
Workmanship: Exposed copper or bare leads will be permitted to a maximum of .020 inch (0.51 mm) from the
body egress. For parts without standoffs, workmanship shall be in accordance with MIL-PRF-39014.
Part or Identifying Number (PIN): Established reliability - M39014/01-(dash number from table I).
Nonestablished reliability - M39014/01C (failure rate level M dash number from table I).
Marking: In accordance with MIL-PRF-39014, except the minimum marking as shown in the following example
will be permitted. Full marking shall be included on the package.
Front
.
Specification sheet no.
Four digit dash number
M390
14/01
1201
Reverse
J--
9301
A
J = Jan, and two digit manufac-
turer’s code or symbol 1/
Date code in accordance with
MIL-PRF-39014.
Lot code
Established reliability without optional standoff
Front
.
Specification sheet no.
Four digit dash number
C390
14/01
1201
Reverse
J--
9301
A
J = Jan, and two digit manufac-
turer’s code or symbol 1/
Date code in accordance with
MIL-PRF-39014.
Lot code
Nonestablished reliability without optional standoff 2/
Front
M390
14/01
1201V
Front
C390
14/01
1201V
Established reliability with optional standoff
Nonestablished reliability with optional standoff 2/
Supersession data: See table II.
1/ Location of manufacturer’s code or symbol is optional.
2/ NOTE: The reduced marking requirement for nonestablished reliability (product level C) differs from the actual
PIN of the nonestablished reliability part in the placement of the character “C”.
4
MIL-PRF-39014/1G
TABLE I. Dash number and electrical characteristics.
Dash number 1/ 2/
Capacitance
(pF)
Capacitance
tolerance
(± percent)
Failure rate level (%/1,000 hours)
1.0 (M)
1201-
1202-
1203-
1204-
1205-
1206-
1207-
1208-
1209-
1210-
1211-
1212-
1213-
1214-
1215-
1216-
1217-
1218-
1219-
1220-
1221-
1222-
1223-
1224-
1225-
1226-
1227-
1228-
1229-
1230-
1231-
1232-
1233-
1234-
1235-
1236-
1237-
1238-
1239-
1240-
1441-
1442-
1443-
0.1 (P)
1241-
1242-
1243-
1244-
1245-
1246-
1247-
1248-
1249-
1250-
1251-
1252-
1253-
1254-
1255-
1256-
1257-
1258-
1259-
1260-
1261-
1262-
1263-
1264-
1265-
1266-
1267-
1268-
1269-
1270-
1271-
1272-
1273-
1274-
1275-
1276-
1277-
1278-
1279-
1280-
1481-
1482-
1483-
0.01 (R)
1281-
1282-
1283-
1284-
1285-
1286-
1287-
1288-
1289-
1290-
1291-
1292-
1293-
1294-
1295-
1296-
1297-
1298-
1299-
1300-
1301-
1302-
1303-
1304-
1305-
1306-
1307-
1308-
1309-
1310-
1311-
1312-
1313-
1314-
1315-
1316-
1317-
1318-
1319-
1320-
1521-
1522-
1523-
0.001 (S)
1321-
1322-
1323-
1324-
1325-
1326-
1327-
1328-
1329-
1330-
1331-
1332-
1333-
1334-
1335-
1336-
1337-
1338-
1339-
1340-
1341-
1342-
1343-
1344-
1345-
1346-
1347-
1348-
1349-
1350-
1351-
1352-
1353-
1354-
1355-
1356-
1357-
1358-
1359-
1360-
1561-
1562-
1563-
10
10
12
15
15
18
22
22
27
33
33
39
47
47
56
68
68
82
100
100
120
150
150
180
220
220
270
330
330
390
470
470
560
680
680
820
1,000
1,000
1,200
1,500
1,500
1,800
2,200
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
20
10
10
DC
rated
voltage
(volts)
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
100
100
100
100
100
See footnotes at end of table.
5
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
