General-purpose Basic Switch
Z
Best-selling Basic Switch Boasting High
Precision and Wide Variety
• A large switching capacity of 15 A with high repeat accuracy.
• A wide range of variations in contact form for your selection:
basic, split-contact and maintained-contact.
• A series of standard models for micro loads is available.
• A series of molded terminal-type models incorporating
safety terminal protective cover is available.
Model Number Structure
Available types
Basic models
General-purpose
Drip-proof
Without terminal protective cover
With terminal protective cover
Molded terminal
Split-contact models
Maintained-contact models
General-purpose
General-purpose
Basic Models
General-purpose
•
A variety of actuators is available for a wide range of application.
•
The contact mechanism of models for micro loads is a crossbar
type with gold-alloy contacts, which ensures highly reliable
operations for micro loads.
•
Contact Gap:
H2: 0.20 mm (extra-high-sensitivity)
H:
0.25 mm (high-sensitivity, micro voltage current load)
G:
0.5 mm (standard)
E:
1.8 mm (high-capacity)
F:
1.0 mm (split-contact models)
Split-contact Models
•
This type is identical in construction to the general-purpose basic
switch except that it has two pairs of simultaneous acting contacts
by splitting moving contacts.
•
Since the moving contacts are connected to a common terminal,
either parallel or series connection is possible.
•
Highly reliable micro load switching is ensured if the model is used
as a twin-contact switch.
Maintained-contact Models
•
The maintained-contact type has a reset button at the bottom of the
switch case, in addition to the pushbutton (plunger) located on the
opposite side of the reset button. Use these buttons alternately.
•
Since the Switch has greater pretravel than overtravel, it is suitable
for use in reversible control circuits, manual reset circuits, safety
limit circuits, and other circuits which are not preferable for
automatic resetting. (For further details, refer to individual
datasheets.)
Drip-proof
•
These Switches use a rubber boot on the actuator and adhesive fill
between the case and cover to increase resistance to drips.
•
Models with drip-proof terminal protective covers and molded
terminals with resin filling are also available.
General-purpose Basic Switch
Z
147
■
Model Number Legend
Basic Models
Z-
1 2 3 4
-
5
Long hinge lever
Low-force
wire
hinge lever (low OF)
W52:
Low-force
wire
hinge lever (high OF)
W22:
Short hinge roller lever
W2:
Hinge roller lever
W25:
Hinge roller lever
5. Terminals
(large roller)
None: Solder terminal
W49:
Short hinge
B:
Screw terminal
cross roller lever
(with toothed
washer)
W54:
Hinge cross roller lever
B5V: Screw terminal
with
W2277: Unidirectional short hinge
terminal cover
roller lever (low OF)
(for Z-15G@A55 only)
M:
Reverse hinge lever
M22:
Reverse short hinge roller lever
M2:
Reverse hinge roller lever
NJ:
Flexible rod (high OF)
NJS:
Flexible rod (low OF)
W44:
W78:
4. Degree of Protection
None: General-purpose
55:
Drip-proof
A55: Drip-proof
(including terminals)
1. Ratings
01: 0.1 A (micro load)
15: 15 A
3. Actuator
None: Pin plunger
S:
Slim spring plunger
D:
Short spring plunger
2. Contact Gap
K:
Spring plunger (medium OP)
H2: 0.20 mm
K3: Spring plunger (high OP)
(extra-high sensitivity) Q3: Panel mount plunger (low OP)
H: 0.25 mm
Q:
Panel mount plunger
(high-sensitivity,
(medium OP)
micro load)
Q8: Panel mount plunger (high OP)
G: 0.5 mm
Q22: Panel mount roller plunger
E: 1.8 mm (high-capacity) Q21: Panel mount cross roller plunger
L:
Leaf spring (high OF)
L2:
Roller leaf spring
W21: Short hinge lever
W:
Hinge lever (low OF)
W3: Hinge lever (medium OF)
W32: Hinge lever (high OF)
W4: Low-force hinge lever
Split-contact Models
Z - 10 F
Y -B
1 2 3 4 5
1. Ratings
10: 10 A (split-contact models)
2. Contact Gap
F: 1 mm (high-capacity)
3. Actuator
None: Pin plunger
S:
Slim spring plunger
D:
Short spring plunger
Q:
Panel mount plunger
Q22: Panel mount roller plunger
W:
Hinge lever
W22: Short hinge roller lever
W2: Hinge roller lever
M22: Reverse short hinge roller lever
4. Construction
Y:
Split-contact type
5. Terminals
None: Solder terminal
B:
Screw terminal
(with toothed
washer)
Maintained-contact models
Z - 15 E
R
1 2 3 4
1. Ratings
15: 15 A
2. Contact Gap
E: 1.8 mm (high-capacity)
3. Actuator
None: Pin plunger
S:
Slim spring plunger
W:
Hinge lever
4. Construction
R:
Maintained-contact
models
Drip-proof with Molded Terminal Models
Z-
1
55 - M
2 3
4
3. Direction of Lead Outlets
L:
Left
R:
Right
D:
Descending
D type
R type
4. Length of Leads
1:
1m
3:
3m
M
1. Drip-proof model
(Insert model number of
basic,
drip-proof
version with
solder terminals)
2. Lead Outlets
None: VSF
E:
VCT
L type
148
General-purpose Basic Switch
Z
Classification
Actuator
Contact gap
Terminal *1
Hinge cross roller
lever
Unidirectional
short hinge roller
lever
Reverse hinge lever
*2
Reverse short hinge
roller lever *2
Reverse hinge
roller lever *2
Parallel
Standard
G (0.5 mm)
Model
Z-15GW54
Z-15GW54-B
Z-15GW2277
Z-15GW2277-B
Z-15GM
Z-15GM-B
Z-15GM22
Z-15GM22-B
Z-15GM2
Z-15GM2-B
High-sensitivity
H (0.25 mm)
Model
---
Extra-high
sensitivity
H2 (0.20 mm)
Model
---
High-capacity
E (1.8 mm)
Model
---
Micro load
H (0.25 mm)
Model
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
*1.
: Solder terminal
: Screw terminal
*2. The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers
are freed by operating the levers. Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally
pressed.
Split-contact Models
Contact gap
Actuator
Pin plunger
Slim spring plunger
Short spring plunger
Terminal *1
F (1.0 mm)
Model
---
Z-10FY-B
---
Z-10FSY-B
---
Z-10FDY-B
---
Panel mount plunger
Panel mount roller
plunger
Hinge lever
Short hinge roller
lever
Hinge roller lever
Reverse short hinge
roller lever *2
Z-10FQY-B
---
Z-10FQ22Y-B
---
Z-10FWY-B
---
Z-10FW22Y-B
---
Z-10FW2Y-B
---
Z-10FM22Y-B
Maintained-contact Models
Actuator
Pin plunger
Slim spring plunger
Hinge lever
Model
Z-15ER
Z-15ESR
Z-15EWR
*1.
: Solder terminal
: Screw terminal
*2. The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers
are freed by operating the levers. Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally
pressed.
150
General-purpose Basic Switch
Z
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
