MX29F002/002N T/B
2M-BIT [256K x 8] CMOS FLASH MEMORY
FEATURES
•
•
•
262,144x 8 only
Fast access time: 55/70/90/120ns
Low power consumption
- 30mA maximum active current(5MHz)
- 1uA typical standby current
Programming and erasing voltage 5V ± 10%
Command register architecture
- Byte Programming (7us typical)
- Sector Erase (16K-Byte x1, 8K-Byte x 2, 32K-Byte
x1, and 64K-Byte x 3)
Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors or the
whole chip with Erase Suspend capability.
- Automatically programs and verifies data at specified
address
Erase Suspend/Erase Resume
- Suspends an erase operation to read data from, or
program data to, a sector that is not being erased, then
resumes the erase operation.
Status Reply
- Data polling & Toggle bit for detection of program and
erase cycle completion.
Sector protection
- Hardware method to disable any combination of
sectors from program or erase operations
- Sector protect/unprotect for 5V only system or 5V/12V
system
100,000 minimum erase/program cycles
Latch-up protected to 100mA from -1 to VCC+1V
Boot Code Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
Hardware RESET pin(only for 29F002T/B)
- Resets internal state machine to read mode
Low VCC write inhibit is equal to or less than 3.2V
Package type:
- 32-pin PDIP
- 32-pin PLCC
- 32-pin TSOP (Type 1)
20 years data retention
•
•
•
•
•
•
•
•
•
•
•
•
•
GENERAL DESCRIPTION
The MX29F002T/B is a 2-mega bit Flash memory organ-
ized as 256K bytes of 8 bits only. MXIC's Flash memories
offer the most cost-effective and reliable read/write non-
volatile random access memory. The MX29F002T/B is
packaged in 32-pin PDIP,PLCC and 32-pin TSOP(I). It is
designed to be reprogrammed and erased in-system or in-
standard EPROM programmers.
The standard MX29F002T/B offers access time as fast as
55ns, allowing operation of high-speed microprocessors
without wait states. To eliminate bus contention, the
MX29F002T/B has separate chip enable (CE) and output
enable (OE) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29F002T/B uses a command register to manage this
functionality. The command register allows for 100% TTL
level control inputs and fixed power supply levels during
erase and programming, while maintaining maximum
EPROM compatibility.
MXIC's Flash technology reliably stores memory contents
even after 100,000 erase and program cycles. The MXIC
cell is designed to optimize the erase and programming
mechanisms. In addition, the combination of advanced
tunnel oxide processing and low internal electric fields for
erase and programming operations produces reliable
cycling. The MX29F002T/B uses a 5.0V ± 10% VCC
supply to perform the High Reliability Erase and auto
Program/Erase algorithms.
The highest degree of latch-up protection is achieved with
MXIC's proprietary non-epi process. Latch-up protection is
proved for stresses up to 100 milliamps on address and
data pin from -1V to VCC + 1V.
P/N: PM0547
1
REV. 1.5, MAR. 28, 2005
MX29F002/002N T/B
PIN CONFIGURATIONS
32 PDIP
RESET
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
Q0
Q1
Q2
GND
32 TSOP (TYPE 1)
NC on MX29F002NT/B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
WE
A17
A14
A13
A8
A9
A11
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
A11
A9
A8
A13
A14
A17
WE
VCC
(NC on MX29F002NT/B) RESET
A16
A15
A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
GND
Q2
Q1
Q0
A0
A1
A2
A3
MX29F002T/B
MX29F002T/B
(NORMAL TYPE)
32 PLCC
NC on MX29F002NT/B
RESET
VCC
A12
A15
A16
A17
WE
SECTOR STRUCTURE
A17~A0
3FFFFH
3BFFFH
A14
A13
A8
A9
9
16 K-BYTE
(BOOT SECTOR)
8
K-BYTE
K-BYTE
K-BYTE
K-BYTE
K-BYTE
K-BYTE
A7
A6
A5
A4
A3
A2
A1
A0
Q0
5
4
1
32
30
29
39FFFH
8
37FFFH
2FFFFH
64
1FFFFH
64
0FFFFH
64
00000H
32
MX29F002T/B
25
A11
OE
A10
CE
13
14
Q1
Q2
VSS
17
Q3
Q4
Q5
21
20
Q6
Q7
MX29F002T Sector Architecture
A17~A0
3FFFFH
64
2FFFFH
64
1FFFFH
0FFFFH
07FFFH
05FFFH
03FFFH
00000H
8
8
K-BYTE
K-BYTE
64
32
K-BYTE
K-BYTE
K-BYTE
K-BYTE
PIN DESCRIPTION
SYMBOL
A0~A17
Q0~Q7
CE
WE
RESET
OE
VCC
GND
PIN NAME
Address Input
Data Input/Output
Chip Enable Input
Write Enable Input
Hardware Reset Pin/Sector Protect Unlock
Output Enable Input
Power Supply Pin (+5V)
Ground Pin
16 K-BYTE
(BOOT SECTOR)
MX29F002B Sector Architecture
P/N: PM0547
REV. 1.5, MAR. 28, 2005
2
MX29F002/002N T/B
BLOCK DIAGRAM
WRITE
WE
OE
WP
RESET
CONTROL
INPUT
LOGIC
HIGH VOLTAGE
MACHINE
(WSM)
PROGRAM/ERASE
STATE
X-DECODER
MX29F002
FLASH
ARRAY
ARRAY
ADDRESS
LATCH
A0~A17
AND
BUFFER
STATE
REGISTER
SENSE
AMPLIFIER
Y-DECODER
Y-PASS GATE
SOURCE
HV
COMMAND
DATA
DECODER
PGM
DATA
HV
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
Q0-Q7
I/O BUFFER
P/N: PM0547
REV. 1.5, MAR. 28, 2005
3
MX29F002/002N T/B
AUTOMATIC PROGRAMMING
The MX29F002T/B is byte programmable using the
Automatic Programming algorithm. The Automatic
Programming algorithm does not require the system to
time out or verify the data programmed. The typical chip
programming time of the MX29F002T/B at room temperature
is less than 3.5 seconds.
cally pre-program and verify the entire array. Then the
device automatically times the erase pulse width, verifies
the erase, and counts the number of sequences. A status
bit similar to DATA polling and status bit toggling between
consecutive read cycles provides feedback to the user as
to the status of the programming operation.
Commands are written to the command register using
standard microprocessor write timings. Register contents
serve as inputs to an internal state-machine which controls
the erase and programming circuitry. During write cycles,
the command register internally latches address and data
needed for the programming and erase operations. During
a system write cycle, addresses are latched on the falling
edge, and data are latched on the rising edge of WE .
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, relia-
bility, and cost effectiveness. The MX29F002T/B electri-
cally erases all bits simultaneously using Fowler-Nord-
heim tunneling. The bytes are programmed one byte at a
time using the EPROM programming mechanism of hot
electron injection.
During a program cycle, the state-machine will control the
program sequences and command register will not re-
spond to any command set. During a Sector Erase cycle,
the command register will only respond to Erase Suspend
command. After Erase Suspend is completed, the device
stays in read mode. After the state machine has com-
pleted its task, it will allow the command register to
respond to its full command set.
AUTOMATIC CHIP ERASE
Typical erasure at room temperature is accomplished in
less than 3 seconds. The device is erased using the
Automatic Erase algorithm. The Automatic Erase algorithm
automatically programs the entire array prior to electrical
erase. The timing and verification of electrical erase are
internally controlled by the device.
AUTOMATIC SECTOR ERASE
The MX29F002T/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. Sector erase modes allow
sectors of the array to be erased in one erase cycle. The
Automatic Sector Erase algorithm automatically programs
the specified sector(s) prior to electrical erase. The timing
and verification of electrical erase are internally controlled
by the device.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write a program set-up commands include 2
unlock write cycle and A0H and a program command
(program data and address). The device automatically
times the programming pulse width, verifies the program,
and counts the number of sequences. A status bit similar
to DATA polling and a status bit toggling between
consecutive read cycles, provides feedback to the user as
to the status of the programming operation.
AUTOMATIC ERASE ALGORITHM
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using standard
microprocessor write timings. The device will automati-
P/N: PM0547
REV. 1.5, MAR. 28, 2005
4
MX29F002/002N T/B
TABLE 1. SOFTWARE COMMAND DEFINITIONS
Command
Bus
Cycle
Reset
Read
Read Silicon ID
Sector Protect
Verification
Program
Chip Erase
Sector Erase
Sector Erase Suspend
Sector Erase Resume
Unlock for sector
protect/unprotect
Note:
1. ADI = Address of Device identifier; A1=0,A0 =0 for manufacture code,A1=0, A0 =1 for device code (Refer to Table 3).
DDI = Data of Device identifier : C2H for manufacture code, 00B0h/0034h for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2. PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address to the sector to be erased.
3.The system should generate the following address patterns: 555H or 2AAH to Address A0~A10. Address bit A11~A17=X=Don't
care for all address commands except for Program Address (PA) and Sector Address (SA). Write Sequence may be initiated
with A11~A17 in either state.
4.For Sector Protect Verification Operation : If read out data is 01H, it means the sector has been protected. If read out data is 00H,
it means the sector is still not being protected.
4
6
6
1
1
6
555H AAH
555H AAH
555H AAH
XXXH B0H
XXXH 30H
555H AAH
2AAH 55H
555H 80H
555H AAH
2AAH 55H
555H 20H
2AAH 55H
2AAH 55H
2AAH 55H
555H A0H
555H 80H
555H 80H
1
1
4
4
First Bus
Cycle
Addr Data
XXXH F0H
RA
RD
2AAH 55H
2AAH 55H
555H 90H
555H 90H
ADI
(SA)
DDI
00H
Second Bus
Cycle
Addr Data
Third Bus
Cycle
Addr Data
Fourth Bus
Cycle
Addr Data
Fifth Bus
Cycle
Addr Data
Sixth Bus
Cycle
Addr Data
555H AAH
555H AAH
(X02H) 01H
PA
PD
2AAH
2AAH
55H 555H 10H
55H SA
30H
555H AAH
555H AAH
COMMAND DEFINITIONS
Device operations are selected by writing specific address
and data sequences into the command register. Writing
incorrect address and data values or writing them in the
improper sequence will reset the device to the read mode.
Table 1 defines the valid register command sequences.
Note that the Erase Suspend (B0H) and Erase Resume
(30H) commands are valid only while the Sector Erase
operation is in progress. Either of the two reset command
sequences will reset the device(when applicable).
P/N: PM0547
REV. 1.5, MAR. 28, 2005
5
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
