Rev. 2.19.09_167
PTH12030 Series
1 of 6
Embedded Power for
Business-Critical Continuity
PTH12040
12 Vin
Total Power:
# of Outputs:
275 Watts
Single
Rev. 03.26.10_168
PTH12040 Series
1 of 5
Specifications
Special Features
• 50 A output current
• 12 V input voltage (8 Vdc to
14 Vdc)
• Wide-output voltage adjust
• 0.8 Vdc to 5.5 Vdc
• Auto-track™ sequencing*
• Margin up/down controls
• Efficiencies up to 96%
• Output ON/OFF inhibit
• Differential remote sense
• Programmable Under-
Voltage Lockout (UVLO)
• Point-of-Load-Alliance (POLA)
compatible
• Available RoHS compliant
• 2 Year Warranty
(5)
Input
Input voltage range:
Input standby current:
Remote ON/OFF:
Start-up time:
Undervoltage lockout:
+ Pin 8 open
Track input current:
(See Note 8)
Pin 18 (See Note 7)
(See Note 3)
(See Note 2)
(See Note 1)
8 - 14 Vdc
35 mA typ.
Positive logic
1 V/ms
6.6 - 7.5 V typ.
- 0.13 mA
0.8 - 5.5 Vdc
(See Note 1)
± 2.0% Vo
± 5 mV typ.
± 5 mV typ.
(See Note 1)
20 MHz bandwidth
(See Note 4)
(See Note 7)
± 3.0% Vo
0A
15 mV typ.
70 µs recovery time
Overshoot/undershoot 150 mV
Margin adjustment:
± 5.0% Vo
Output
Voltage adjustability:
Setpoint accuracy:
Line regulation:
Load regulation:
Total regulation:
Minimum load:
Ripple and noise:
Transient response:
Safety
• UL/cUL CAN/CSA-C22.2
No. 60950, File No. E174104
• TÜV Product Service
(EN60950) Certificate No.
B 04 06 38572 044
• CB Report and Certificate
to IEC60950, Certificate No.
US/8292/UL
All specifications are typical at nominal input, full load at 25 °C unless otherwise stated
Cin = 1000 µF, Cout = 660 µF
*Auto-track™ is a trade mark of
Texas Instruments
Embedded Power for
Business-Critical Continuity
Rev. 03.26.10_168
PTH12040 Series
2 of 5
EMC Characteristics
Electrostatic discharge:
Conducted immunity:
Radiated immunity:
EN61000-4-2, IEC801-2
EN61000-4-6
EN61000-4-3
General Specifications
Efficiency:
Insulation voltage:
Switching frequency:
Approvals and standards:
Material flammability:
Dimensions:
Weight:
MTBF:
Telcordia SR-332
(L x W x H)
See efficiency table on page 3
Non-Isolated
1.05 Mhz.
EN60950, UL/cUL60950
UL94V-0
51.94 x 26.54 x 9.07 mm
2.045 x 1.045 x 0.357 in
17g (60 oz)
2,500,000 hours
Environmental Specifications
Thermal performance:
MSL (‘Z’ suffix only):
Operating ambient, temperature
Non-operating
JEDEC J-STD-020C
-40 °C to +85 °C
-40 °C to +125 °C
Level 3
Protection
Short circuit:
Thermal:
Auto reset
95 A
Auto recovery
Embedded Power for
Business-Critical Continuity
Rev. 03.26.10_168
PTH12040 Series
3 of 5
Ordering Information
Output Power
(max)
275 W
Input
Voltage
8 - 14 Vdc
Output
Voltage
0.8 - 5.5 Vdc
Output Currents
Min
0A
Max
50 A
Efficiency
(max)
96%
Regulation
Line
± 5 mV
Load
± 5 mV
PTH12040W
Model Numbers
(9, 10)
Part Number System with Options
PTH12040WAS
Product Family
Point of Load Alliance
Compatible
Input Voltage
12 = 12 V
Output Current
04 = 50 A
Mechanical Package
Always 0
Mounting Option
(9)
D = Horizontal Through-Hole (RoHS 6/6)
H = Horizontal Through-Hole (RoHS 5/6)
S = Surface-Mount Solder Ball (RoHS 5/6)
Z = Surface-Mount Solder Ball (RoHS 6/6)
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide
Output Voltage Adjustment of the PTH12040W Series
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH12040W. It is no longer necessary to purchase a variety of modules
in order to cover different output voltages. The output voltage can be trimmed in
a range of 0.8 Vdc to 5.5 Vdc. When the PTH12040W converter leaves the factory
the output has been adjusted to the default voltage of 0.8 V.
Efficiency Table - PTH12040W
(IO = 35 A)
Output Voltage
Vo = 5.0 V
Vo = 3.3 V
Vo = 2.5 V
Vo = 2.0 V
Vo = 1.8 V
Vo = 1.5 V
Vo = 1.2 V
Vo = 1.0 V
Vo = 0.8 V
Efficiency
96%
95%
93%
92%
91%
90%
88%
86%
82%
Notes
The set-point voltage tolerance is affected by the tolerance and stability of
RSET. The stated limit is unconditionally met if RSET has a tolerance of 1% with
100 ppm/˚C or better temperature stability.
2 This control pin has an internal pull-up to 5 V nominal. If it is left open-circuit
the module will operate when input power is applied. A small low leakage
(<100 nA) MOSFET is recommended for control. For further information,
consult the related application note. For further information, consult
Application Note 193.
3 A 1000 µF input capacitor is required for proper operation. The capacitor must
be rated for a minimum of 300 mA rms of ripple current.
4 This is with a 1 A/µs loadstep, 50 to 100% I
omax
, I
o
= 680 µF.
5 See Figures 1 and 2 for safe operating curves.
6 When the set-point voltage is adjusted higher than 3.6 V, a 10 V minimum
input voltage is recommended.
7 A small low-leakage (<100 nA) MOSFET is recommended to control this pin.
The open circuit voltage is less than 1 Vdc.
8 These are the default voltages. They may be adjusted using the ‘UVLO Prog’
control input. Consult Application Note No. 193 for further information.
9 To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH12040WAZ. To order Pb-free (RoHS
compatible) through-hole parts replace the mounting option ‘H’ with ‘D’, e.g.
PTH12040WAD.
10 NOTICE: Some models do not support all options. Please contact your local
Emerson Network Power representative or use the on-line model number search
tool at http://www.Emerson.com/EmbeddedPower to find a suitable alternative.
1
Embedded Power for
Business-Critical Continuity
Characteristic Data
90
TEMPERATURE (ºC)
TEMPERATURE (ºC)
80
70
60
50
40
30
20
0
10
20
30
40
50
OUTPUT CURRENT (A)
Figure 1 - Safe Operating Area
Vin = 12 V, Output Voltage = 3.3 V (See Note A)
Nat conv
100 LFM
200 LFM
400 LFM
Rev. 03.26.10_168
PTH12040 Series
4 of 5
90
80
70
60
50
40
30
20
10
0
0
10
20
30
40
50
Nat conv
100 LFM
200 LFM
400 LFM
OUTPUT CURRENT (A)
Figure 2 - Safe Operating Area
Vin = 12 V, Output Voltage = 1.2 V (See Note A)
19
20
Margin
Down
18
Track
+Sense
11
9
100
EFFICIENCY (%)
90
80
70
60
50
40
0
10
20
30
40
50
Vin
2
4
6
8
Margin
up
Vin
Vo
12
15
Vo
Vout
5.0V
3.3V
2.5V
1.8V
1.2V
0.8V
Ci
560uF
(Required)
UVLO
Inhibit
7
1
GND
3
5
10
GND
13
16
-Sense
Vo Adj
17
14
Rset
1%
0.05W
Co2
330uF
Co1
330uF
OUTPUT CURRENT (A)
Figure 3 - Efficiency vs Load Current
Vin = 12 V (See Note B)
Figure 4 - Standard Application
Notes
A
B
SOA curves represent the conditions at which internal components are within
the Emerson Network Power derating guidelines.
Characteristic data has been developed from actual products tested at 25 °C.
This data is considered typical data for the converter.
Embedded Power for
Business-Critical Continuity
Mechanical Drawings
2.045 (51.94)
0.060 (1.52)
0.125 (3.17)
6 Places
0.060
(1.52)
17
0.125
(3.17)
3 Places
16
18
19
20
1.045
(26.54)
15 14 13
0.375
(9.52)
0.375
(9.52)
1.875 (47.62)
0.375
(9.52)
0.140
(3.55)
ø0.040 (1.02)
20 Places
12 11 10
9
8
Lowest
Component
0.010 MIN.
(0.25)
Bottom side
Clearance
Americas
Rev. 03.26.10_168
PTH12040 Series
5 of 5
5810 Van Allen Way
Carlsbad, CA 92008
USA
Telephone: +1 760 930 4600
Facsimile: +1 760 930 0698
Europe (UK)
0.925
(23.49)
1
0.375
(9.52)
2
3
4
5
6
7
0.125 (3.17)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
0.250
(6.35)
2 Places
0.375
(9.52)
Host Board
0.357 (9.07)
MAX.
SIDE VIEW
0.375
(9.52)
Asia (HK)
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places 0.030 (0.76)
3 Places 0.010 (0.25)
TOP VIEW
Figure 5 - Plated Through-Hole
2.045 (51.94)
0.060 (1.52)
0.125 (3.17)
6 Places
0.060
(1.52)
17
0.125
(3.17)
3 Places
16
18
19
20
1.045
(26.54)
15 14 13
0.375
(9.52)
0.375
(9.52)
1.875 (47.62)
0.375
(9.52)
0.370 (9.40)
MAX.
After solder reflow
on customer board
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
Telephone: +852 2176 3333
Facsimile: +852 2176 3888
For global contact, visit:
www.Emerson.com/EmbeddedPower
techsupport.embeddedpower
@emerson.com
While every precaution has been taken to ensure
accuracy and completeness in this literature, Emerson
Network Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
12 11 10
9
8
Solder Ball
ø
0.040 (1.02)
20 Places
0.925
(23.49)
Emerson Network Power.
The global leader in enabling
business-critical continuity.
AC Power
1
0.375
(9.52)
2
3
4
5
6
7
0.250
(6.35)
2 Places
0.375
(9.52)
0.125 (3.17)
0.375
(9.52)
SIDE VIEW
Connectivity
DC Power
Embedded Computing
Embedded Power
Monitoring
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places 0.030 (0.76)
3 Places 0.010 (0.25)
TOP VIEW
Figure 6 - Surface-Mount
Pin Connections
Pin No.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin Connections cont.
Pin No.
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin Connections cont.
Pin No.
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Outside Plant
Power Switching & Controls
Precision Cooling
Racks & Integrated Cabinets
Services
Surge Protection
EmersonNetworkPower.com
Emerson Network Power and the Emerson
Network Power logo are trademarks and
service marks of Emerson Electric Co.
©2010 Emerson Electric Co.
Function
Ground
Vin
Ground
Vin
Ground
Vin
Inhibit*
Function
UVLO Programming
Vout
Ground
Vs+
Vout
Ground
Vs-
Function
Vout
Ground
Adjust
Track
Margin Up*
Margin Down*
* Denotes negative logic:
Open = Normal operation
Ground = Function active
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
