120W Single Output Switching Power Supply
■
Features :
HLG-120H
series
‧
Universal AC input / Full range (up to 305VAC)
‧
Built-in active PFC function
‧
High efficiency up to 93.5%
‧
Protections: Short circuit / Over current / Over voltage / Over temperature
‧
Cooling by free air convection
‧
OCP point adjustable through output cable or internal potentiometer
‧
IP67 / IP65 design for indoor or outdoor installations
‧
Three in one dimming function (1~10Vdc or PWM signal or resistance)
‧
Suitable for LED lighting and street lighting applications
‧
Compliance to worldwide safety regulations for lighting
‧
Suitable for dry / damp / wet locations
‧
5 years warranty (Note.10)
F
110
M
M
SELV
IP65 IP67
HLG-120H-12 A
Blank : IP67 rated. Cable for I/O connection.
A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.
D (option, safety pending) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
SPECIFICATION
MODEL
DC VOLTAGE
HLG-120H-12
12V
CONSTANT CURRENT REGION
Note.4
6 ~12V
RATED CURRENT
10A
HLG-120H-15
15V
7.5 ~ 15V
8A
HLG-120H-20
20V
10 ~ 20V
6A
120W
150mVp-p
17 ~ 22V
HLG-120H-24
24V
12 ~ 24V
5A
120W
150mVp-p
22 ~ 27V
HLG-120H-30
30V
15 ~ 30V
4A
120W
200mVp-p
27 ~ 33V
2 ~ 4A
±1.0%
±0.5%
±0.5%
HLG-120H-36
36V
18 ~ 36V
3.4A
122.4W
200mVp-p
33 ~ 40V
1.7 ~ 3.4A
±1.0%
±0.5%
±0.5%
HLG-120H-42
42V
21 ~ 42V
2.9A
121.8W
200mVp-p
38 ~ 46V
1.4 ~ 2.9A
±1.0%
±0.5%
±0.5%
HLG-120H-48
48V
24 ~ 48V
2.5A
120W
200mVp-p
43 ~ 53V
1.2 ~ 2.5A
±1.0%
±0.5%
±0.5%
HLG-120H-54
54V
27 ~ 54V
2.3A
124.2W
200mVp-p
49 ~ 58V
1.1 ~ 2.3A
±1.0%
±0.5%
±0.5%
RATED POWER
120W
120W
RIPPLE & NOISE (max.)
Note.2
150mVp-p
150mVp-p
VOLTAGE ADJ. RANGE
Note.6
10.8 ~ 13.5V 13.5 ~ 17V
OUTPUT
CURRENT ADJ. RANGE
Can be adjusted by internal potentiometer A type only
5 ~ 10A
4 ~ 8A
3 ~ 6A
2.5 ~ 5A
VOLTAGE TOLERANCE
Note.3
±2.5%
±2.0%
±1.0%
±1.0%
±0.5%
±2.0%
±0.5%
±1.5%
±0.5%
±0.5%
±0.5%
±0.5%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
Note.8
1200ms,50ms/115VAC
500ms,50ms/230VAC at full load ; B type 1200ms,200ms/115VAC
500ms,200ms/230VAC at 95% load
12ms at full load
230VAC / 115VAC
127 ~ 431VDC
Note.5
90 ~ 305VAC
VOLTAGE RANGE
FREQUENCY RANGE
47 ~ 63Hz
INPUT
POWER FACTOR (Typ.)
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION
THD< 20% when output loading
≧
50% at 115VAC/230VAC input and output loading
≧
75% at 277VAC input
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER CURRENT
SHORT CIRCUIT
93%
93%
92%
93%
1.4A / 115VAC
0.6A / 230VAC
0.55A / 277VAC
COLD START 60A(t
width
=375 s measured at 50% I
peak
) at 230VAC
μ
<0.75mA / 277VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Constant current limiting, recovers automatically after fault condition is removed
14 ~ 17V
18 ~ 21V
28 ~ 34V
34 ~ 38V
41 ~ 46V
47 ~ 53V
23 ~ 27V
Protection type :
Shut down o/p voltage with auto-recovery or re-power on to recovery
Shut down o/p voltage, recovers automatically after temperature goes down
-40 ~ +70
℃
(Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80
℃
, 10 ~ 95% RH
±0.03%/
℃
(0 ~ 50
℃
)
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08, ENEC, TUV EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1,
J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1
I/P-O/P:3.75KVAC
I/P-FG:2KVAC
O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
℃
/ 70% RH
Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (
≧
50% load) ; EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A
192.2K hrs min. MIL-HDBK-217F (25
℃
)
220*68*38.8mm (L*W*H)
1.12Kg; 12pcs/14.4Kg/0.8CUFT
92%
93%
93%
93.5%
93.5%
PROTECTION
OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
54 ~ 63V
59 ~ 65V
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
Note.7
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
OTHERS
DIMENSION
PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
℃
of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to "DRIVING METHODS OF LED MODULE".
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. A type only.
7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.
8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
10. Refer to warranty statement.
11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
120W Single Output Switching Power Supply
Power Factor Characteristic
Constant Current Mode
1 .0 0
0 .9 8
0 .9 6
0 .9 4
0 .9 2
0 .9 0
0 .8 8
0 .8 6
0 .8 4
0 .8 2
0 .8 0
0 .7 8
50%
60%
70%
80%
90%
100%
(120W)
HLG-120H
series
277V ac
230V ac
115V ac
LOAD
EFFICIENCY vs LOAD (48V Model)
HLG-120H series possess superior working efficiency that up to 93.5% can be reached in field applications.
96
92
88
84
80
76
72
68
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
277Vac
230Vac
115Vac
DRIVING METHODS OF LED MODULE
There are t wo major kinds of LED drive method "direct drive" and "with LED driver".
A typical LE D power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" t o drive the LEDs.
Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
In t he constant current region, the highest voltage at the out put of t he driver
depends on the configurat ion of the end sys tems.
Should there be any compatibility issues, please cont act MEAN WELL.
(A) Constant
Voltage area
(B)
Constant
Current region
100
50
100
Io (%)
Typical LE D power supply I-V curve
File Name:HLG-120H-SPEC 2014-05-30
120W Single Output Switching Power Supply
DIMMING OPERATION (for B-type only)
HLG-120H
series
FG (Green/Yellow)
AC/L( Brown)
AC/N(Blue)
HLG-120H
DIM +(B lue)
DIM -(White)
-V(B la ck)
+V(Red)
※
Built-in 3 in 1 dimming f unction, I P67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or
1 ~ 10Vdc or 10V PWM signal bet ween DIM+ and DIM-.
※
Please DO NOT connect "DI M-" t o "-V".
※
Ref erence resistance value for output current adjustment (Typical)
Single driver
10KΩ 20KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ
Resistance
Multiple drivers
value
(N =drive r quantity for sy nc hroniz ed
10K
Ω
/N 20K
Ω
/N 30K
Ω
/N 40K
Ω
/N 50K
Ω
/N 60K
Ω
/N 70K
Ω
/N 80K
Ω
/N 90K
Ω
/N 100K
Ω
/N
d im mi n g o pe r ati o n)
OPEN
-----
95%~108%
Percent age of rated current
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
※
1 ~ 10V dimming function f or output current adjustment (Typical)
Dimming value
Percent age of rated current
1V
10%
2V
20%
3V
30%
4V
40%
5V
50%
6V
60%
7V
70%
8V
80%
9V
90%
10V
100%
OPEN
95%~108%
※
10V PWM signal for output current adjustment (Typical): Frequency range : 100Hz ~ 3KHz
Duty value
Percent age of rated current
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
60%
60%
70%
70%
80%
80%
90%
90%
100%
100%
OPEN
95%~108%
※Using
the built-in dimming funct ion on B-type model can't t urn the light ing fixture t otally dark. Pleas e refer to t he connection method below t o
achieve 0% bright ness of the lighting fixt ure connecting to the LED power supply unit.
※Direct
connecting to LEDs is suggested, but is not suitable for using additional drivers.
Dimming connection diagram for t urning the lighting fixture ON/OFF :
N
FG
L
Rel ay
Switch
Adj uster
10K~100K Ohms resistanc e
1~10V DC Voltage
10V PWM Signal
Green/
Yellow
Brown
Blue
AC/L
AC/N
HLG-120H
B Type
DIM+
DIM-
V(-)
V(+)
Blue
White
Black
Red
LED Lighting Fixtur e
Using a switch and relay can turn ON/OFF t he lighting f ixture.
1.Output constant current level can be adjusted through out put cable by connecting a
resistance
or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.
2.T he LED light ing f ixture can be turned ON/OFF by the switch.
File Name:HLG-120H-SPEC 2014-05-30
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
