80W Single Output Switching Power Supply
■
Features :
HLP-80H
series
‧
Universal AC input / Full range (up to 305VAC)
‧
Built-in active PFC function
‧
Protections: Short circuit / Over current / Over voltage / Over temperature
‧
Cooling by free air convection
‧
Output constant current level adjustable
‧
Class 2 power unit
‧
Three in one dimming function (1~10Vdc or PWM signal or resistance)
‧
Suitable for built in LED lighting system
‧
Suitable for dry / damp locations
‧
100% full load burn-in test
‧
3 years warranty
M
M
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
RATED POWER
VOLTAGE ADJ. RANGE
CURRENT ADJ. RANGE
12V
5A
60W
15V
9 ~ 15V
5A
75W
150mVp-p
SELV
( for 48V,54V only)
( except for 48V,54V )
HLP-80H-12 HLP-80H-15 HLP-80H-20 HLP-80H-24 HLP-80H-30 HLP-80H-36 HLP-80H-42 HLP-80H-48 HLP-80H-54
20V
12 ~ 20V
4A
80W
150mVp-p
17 ~ 22V
3.2 ~ 4A
±1.0%
±0.5%
±1.0%
24V
14.4 ~ 24V
3.4A
81.6W
150mVp-p
22 ~ 27V
2.72 ~ 3.4A
±1.0%
±0.5%
±0.5%
30V
18 ~ 30V
2.7A
81W
200mVp-p
27 ~ 33V
2.16 ~ 2.7A
±1.0%
±0.5%
±0.5%
36V
21.6 ~ 36V
2.3A
82.8W
200mVp-p
33 ~ 40V
1.84 ~ 2.3A
±1.0%
±0.5%
±0.5%
42V
25.2 ~ 42V
1.95A
81.9W
200mVp-p
38 ~ 46V
48V
28.8 ~ 48V
1.7A
81.6W
200mVp-p
43 ~ 53V
54V
32.4 ~ 54V
1.5A
81W
200mVp-p
49 ~ 58V
1.2 ~ 1.5A
±1.0%
±0.5%
±0.5%
CONSTANT CURRENT REGION
Note.4
7.2 ~12V
RIPPLE & NOISE (max.)
Note.2
150mVp-p
OUTPUT
10.8 ~ 13.5V 13.5 ~ 17V
4 ~ 5A
±0.5%
4 ~ 5A
±2.0%
±0.5%
Can be adjusted by internal potentiometer
1.56 ~ 1.95A 1.36 ~ 1.7A
±1.0%
±0.5%
±0.5%
±1.0%
±0.5%
±0.5%
VOLTAGE TOLERANCE
Note.3
±2.5%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR (Typ.)
INPUT
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
OVER CURRENT
PROTECTION
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY &
EMC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
OTHERS
DIMENSION
PACKING
NOTE
1.
2.
3.
4.
5.
6.
7.
Note.4
±1.5%
±2.0%
Note.6
1200ms,200ms/115VAC
16ms at full load
Note.5
90 ~ 305VAC
500ms,200ms/230VAC at full load
230VAC /115VAC
127 ~ 431VDC
47 ~ 63Hz
PF>0.96/115VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
89.5%
90%
88.5%
90%
0.85A / 115VAC
0.425A / 230VAC
0.4A / 277VAC
COLD START 70A(t
width
=525 s measured at 50% I
peak
) at 230VAC
μ
<0.75mA / 277VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
35 ~ 43V
48 ~ 58V
14 ~ 17V
18 ~ 24V
23 ~ 30V
28 ~ 35V
41 ~ 49V
Protection type :
Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
-40 ~ +70
℃
(Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80
℃
, 10 ~ 95% RH
±
0.03%/
℃
(0 ~ 50
℃
)
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08 (except for 48V, 54V), EN61347-1, EN61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1
I/P-O/P:3.75KVAC
I/P-FG:2KVAC
O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
℃
/ 70% RH
Compliance to EN55015, EN61000-3-2 Class C (
≧
60% load, 12V model
≧
65% load) ; EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A
316.2K hrs min. MIL-HDBK-217F (25
℃
)
167*53*29.5mm (L*W*H)
0.27Kg; 36pcs/11.2Kg/0.67CUFT
87.5%
90%
90%
90%
90%
54 ~ 63V
59 ~ 68V
All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
℃
of ambient temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
Tolerance : includes set up tolerance, line regulation and load regulation.
Please refer to "DRIVING METHODS OF LED MODULE".
Derating may be needed under low input voltages. Please check the static characteristics for more details.
Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
8. Heat Sink HS1,HS2 can not be shorted.
9. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
File Name:HLP-80H-SPEC 2014-03-13
80W Single Output Switching Power Supply
Power Factor Characteristic
Constant Current Mode
1
0 .9 9
0 .9 8
0 .9 7
277VAC
0 .9 6
0 .9 5
0 .9 4
0 .9 3
0 .9 2
50%
60%
70%
80%
90%
100%
230VAC
115VAC
HLP-80H
series
(80W)
LOAD
EFFICIENCY vs LOAD (48V Model)
HLP-80H ser ies possess superior w orking effi ciency that up to 90% can be reache d in field app lications.
94
92
90
88
86
84
82
80
78
76
74
72
70
10%
20%
30%
40%
50%
60%
70% 80%
90% 100%
277VAC
230VAC
115VAC
LOAD
DRIVING METHODS OF LED MODULE
This LED power supply is s ug gested to work in constan t current mod e area (C C) to driv e the LEDs.
100
In the constant current r eg ion, the highest voltage at the output of the dr iver
dep end s on the configur ation of the end s ystems.
Shou ld the re be any compatibility issue s, please con tact MEAN WELL .
Constant
Current area
60
(min.)
Hiccup
Protection
50
100
Io (%)
Typic al LED power supply I-V curve
File Name:HLP-80H-SPEC 2014-03-13
80W Single Output Switching Power Supply
DIMMING OPERATION
HLP-80H
series
FG
AC/N
AC/L
-V
-V
+V
+V
DIM-
DIM+
※
Built-in 3 in 1 dimming function, outpu t constant cur rent level can be adjusted through output connector by 1~10 VDC, PWM signal, or connecting
a resistance between D IM+ and D IM-.
※
Please DO NOT conn ect "D IM- " to " -V".
※
R eferenc e resistance value for output current adjustment (Typical)
Single driver
10KΩ 20KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100 KΩ
Resist ance
Multiple drivers
value
(N=d river qu antity for synchronized
10K
Ω
/N 20K
Ω
/N 30K
Ω
/N 40K
Ω
/N 50K
Ω
/N 60K
Ω
/N 70K
Ω
/N 80K
Ω
/N 90K
Ω
/N 100K
Ω
/N
dimming ope rat ion)
OPEN
--- --
95% ~108%
Percentage of rated cur rent
10%
20%
30%
40%
50%
60%
70%
80%
90%
100 %
※
1 ~ 10V dimming function for output cur rent adjustmen t (Typical)
Di mming value
Percentage of rated cur rent
1V
10%
2V
20%
3V
30%
4V
40%
5V
50%
6V
60%
7V
70%
8V
80%
9V
90%
10V
100 %
OPEN
95% ~108%
※
10V PWM signal for outpu t current adjustment (Typic al): Frequ ency range :100H Z ~ 3KH z
Duty value
Percentage of rated cur rent
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
60%
60%
70%
70%
80%
80%
90%
90%
100 %
100 %
OPEN
95% ~108%
※U
sing the built-i n dimming function can't turn the lighting fixture totally dar k. Please refer to the c onnection method below to achieve 0% bright ness
of the lighting fixtur e con necting to the LED power supp ly unit.
Di mming conn ection diagram for turning the lighting fixture ON/O FF :
N
FG
L
Relay
Switch
Adjuster
10K~100K Ohms resistance
1~10V DC Voltage
10V PWM Signal
Green/
Yellow
Brown
Blue
AC/L
AC/N
HLP-80H
DIM+
DIM-
V(-)
V(+)
Blue
White
Black
Red
LED Lighting Fixture
Us ing a switch and r elay can turn ON /O FF the lighting fi xture.
1.Output con stant current level can be adjusted through outpu t cable by conn ecting a
resistance
or 1~10Vdc or 10V PWM signal between DIM+ and DIM-.
2.T he LED lighting fi xture can be tur ne d ON/OF F by the sw itch.
File Name:HLP-80H-SPEC 2014-03-13
Microchip MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
