74x Series
Features
Chip Resistor Arrays
Low Cost Thick Film Technology
Leadless Surface Mount Construction
Concave or Convex Terminations
Solder Coated Nickel Barrier Pads
Isolated and Bussed Circuit Configurations
Improved TCR Tracking vs. Discrete Resistors
Fewer Placements Than Discrete Components
Tape and Reel Packaging
RoHS Compliant in Accordance with EU Directive 2011/65/EU
- Lead-Free Termination Finish
- Exemption 7(c)-I, Electrical and electronic components containing
lead [Pb] in glass
Applications
Data Communications
Image Processing
Medical Equipment
Networking
Pull-Up/Pull-Down Logic Gates
DDR SDRAM, MDDR, DRAM
Portable Test Equipment
Low Profile High Density Designs
Description
74x Series Chip Arrays are single packaged devices containing an array of homogeneous resistor elements. Arrays
are typically used for convenience when several resistors occupy the same area in a layout. Multiple package
sizes and circuit configurations help save placement costs by reducing application component count.
Ordering Information
Model
741X083
Resistor
Value
103
Resistor
Tolerance
J
RoHS
Compliant
P
Package Code
740X043
741X043
741X083
741C083
741X163
Package Code
742C043
742X083
742C083
742C163
745X101
Package Code
745X102
745C101
745C102
746X101
Code
J
G
F
X
Code Resistor Value *
10k ohm
103
* See Addendum for Standard
EIA Values and Codes
Tolerance
±5%
1
±2%
2, 4
±1%
3, 4
Zero Ohm
Code Termination
P Matte Sn Finish
Notes:
1.
2.
3.
4.
Standard tolerance is ±5% and available for all 740 - 746 package codes; 3-digit resistor codes.
Optional tolerance at ±2% is available for all 741 - 745 package codes, 3-digit resistor codes; except 741X163, 745X101 and 745X102 [±5% and ±1% only].
Optional tolerance at ±1% is available for all 741 - 745 package codes, 4-digit resistor codes; except 745X101 and 745X102 [±5% and ±1% only].
Consult factory for availability with 740X043 package code.
Not all performance combinations and resistor values may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use
of this product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
DOC# 008-0335-0 Rev. P
Page 1 of 11
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
Chip Resistor Arrays
74x Series
Ordering Information
Part Number Examples
Toleranc e /
Value
1 0 O hms
4 9 .9 O hms
1 2 0 O hms
1 k O hms
6 8 k O hms
3 -Digit Code
J
[±5 %]
742C083100JP
Not Available
742C083121JP
742C083102JP
742C083683JP
G
[±2 %]
742C083100GP
Not Available
742C083121GP
742C083102GP
742C083683GP
4 -Digit Code
F
[±1 %]
742C08310R0FP
742C08349R9FP
742C0831200FP
742C0831001FP
742C0836802FP
3-Digit Resistor Code [For 5% and 2% tolerance only.]
st
nd
rd
1 and 2 digits are resistor, 3 digit is number of zeros.
Ex. 102 = 1,000 ohm = 1k ohm
Ex. 683 = 68,000 ohm = 68k ohm
Resistance Values <100 Ohms
“R” indicates decimal for values less than 100 ohm.
Ex. 49R9 = 49.9 ohm
4-Digit Resistor Code [For 1% tolerance only.]
th
First three digits are resistor value, 4 digit is number of zeros.
Ex. 1001 = 1,000 ohm = 1k ohm
Ex. 6802 = 68,000 ohm = 68k ohm
Electrical & Environmental Specifications
Operating Conditions
P ac k age
P C B Ar ea
P er R esist o r
[Sq . I n c h ]
0.0008
0.0015
0.0037
0.0058
0.0058
0.0013
C ir c u it
Ty p e
Isolated
Isolated
Isolated
Bussed
Bussed
Bussed
R esist an c e
R an ge
[o h m ]
10 - 1M
10 - 1M
10 - 1M
10 - 330k
10 - 1M
10 - 100k
R esist an c e
To ler an c e
[% ]
1
+7 0 ° C P o w er
Op er at in g
Tem p er at u r e
Tem p er at u r e
P er R esist o r
2
C o effic ien t
R an ge
[W at t s]
0.031
0.063
0.063
0.063
0.063
0.063
Max im u m
Op er at in g
Vo lt age
12.5V
25V
50V
50V
50V
25V
740
741
742
745X
745C
746
±5% Std.
or
0.5 ohm
±200ppm/°C
-55°C to +125°C
[whichever is
greater]
±250ppm/°C
±200ppm/°C
1. See Ordering Information for other options available.
2. Total Rated Package Power equals total number of resistors times rated Power Per Resistor.
Operating Conditions – 0 ohm
P ac kage
740
741
742
P CB Area
P er Resistor
[Sq. Inc h]
0.0008
0.0015
0.0037
Circ uit
Type
Isolated
Isolated
Isolated
0.0
1.0
2.0
50
Resistanc e
Range
[ohm]
Current @ +7 0 °C
Max P er Element
[A]
Surge Current
Max <1 sec ond
[A]
Max
Resistanc e
[milliohm]
DOC# 008-0335-0 Rev. P
Page 2 of 11
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
Chip Resistor Arrays
74x Series
Electrical & Environmental Specifications
Power Derating Curve – Typical
With the rated ambient temperature set to +70°C, the maximum power [maximum current for 0Ω product] at a temperature of no more
than rated ambient temperature shall be equal to the rated power [rate current for 0Ω product]. The maximum power at a temperature
exceeding the rated ambient temperature shall be a value determined by reducing the rated power according to the power reduction
curve in the figure below.
100
Rated Power Ratio [%]
80
60
40
20
0
-55
0
+70
+125
Ambient Temperature [°C]
Rated Voltage
The rated voltage shall be the DC or AC [effective power frequency] voltage corresponding to the rated power and shall be determined
with the formula shown below. If the determined rated voltage exceeds the maximum operating voltage specified in Operating Conditions
table, the maximum operating voltage shall be the rated voltage.
E = Rated Voaltge [V]
E =
√
PxR
P = Rated Power [W]
R = Nomimal Resistance [Ω]
Environmental Parameters
Test
Thermal Cyc le
Short Time O verload
Moisture Resistanc e
High Temperture Exposure
Load Life
Resistanc e to Solder Heat
Resistanc e to Solvents
Solderability
Maximum Delta R [%]
740
741
742 - 746
1.00
2.00
2.00
3.00
3.00
1.00
---
---
1.00
2.50
5.00
1.00
5.00
2.50
---
---
1.00
1.00
2.00
1.00
2.00
1.00
---
---
Test Desc ription
5 cycles -55°C to +125°C
2½ times rated working voltage for 5 seconds
240 hours @ 0.1 rated load; -10°C to +65°C, 90% RH
1,000 hours @ +125°C, no load
1,000 hours @ +70°C, rated load
10 seconds @ +260°C solder
Isopropyl alcohol, Freon TMC
RMA Flux, +230°C, 5 seconds dip, 95% coverage
DOC# 008-0335-0 Rev. P
Page 3 of 11
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
Chip Resistor Arrays
74x Series
Electrical & Environmental Specifications
Circuit Types
740X043
741X043
742C043
2 Resistors
4 Terminations
741X083
2 Resistors
4 Terminations
741C083
2 Resistors
4 Terminations
742X083
742C083
4 Resistors
8 Terminations
741X163
4 Resistors
8 Terminations
742C163
4 Resistors
8 Terminations
4 Resistors
8 Terminations
746X101
8 Resistors
16 Terminations
745X101
8 Resistors
16 Terminations
745X102
745C101
8 Resistors
10 Terminations
745C102
8 Resistors
10 Terminations
8 Resistors
10 Terminations
8 Resistors
10 Terminations
8 Resistors
10 Terminations
DOC# 008-0335-0 Rev. P
Page 4 of 11
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
Chip Resistor Arrays
74x Series
Mechanical Specifications
Package Drawing – Convex, Type X
Package Drawing – Concave, Type C
Notes
1. JEDEC termination code (e3). Barrier-plating is nickel [Ni] with Matte tin [Sn] finish.
2. Reflow conditions per JEDEC J-STD-020; +260°C maximum, 20 seconds.
3. MSL = 1.
Package Configuration/Dimensions
P ac kage
Code
740X043
741X043
741X083
7 4 1 C0 8 3
741X163
7 4 2 C0 4 3
742X083
7 4 2 C0 8 3
7 4 2 C1 6 3
7 4 5 C1 0 1
7 4 5 C1 0 2
745X101
745X102
746X101
Resistor Size/
Configuration
0201 X 2
0402 X 2
0402 X 4
0402 X 4
0603 X 8
0603 X 2
0603 X 4
0603 X 4
0603 X 8
---
---
---
---
---
Termination
P ads
4
4
8
8
16
4
8
8
16
10
10
10
10
10
# Resistors
Circ uit
Type
Isolated
Isolated
Isolated
Isolated
Isolated
Isolated
Isolated
Isolated
Isolated
Bussed
Bussed
Bussed
Bussed
Bussed
Dimensions
[mm]
L
0.80 ±0.10
1.00 ±0.20
2.00 ±0.20
2.00 ±0.20
3.95 ±0.25
1.60 ±0.20
3.20 ±0.15
3.20 ±0.20
6.40 ±0.20
6.40 ±0.20
6.40 ±0.20
6.40 ±0.20
6.40 ±0.20
3.20 ±0.20
W
0.60 ±0.10
1.00 ±0.20
1.00 ±0.20
1.00 ±0.20
1.60 ±0.15
1.60 ±0.20
1.60 ±0.15
1.60 ±0.20
1.60 ±0.20
3.10 ±0.20
3.10 ±0.20
3.20 ±0.20
3.20 ±0.20
1.60 ±0.15
P
[Typ.]
0.50
0.65
0.50
0.50
0.50
0.80
0.80
0.80
0.80
1.27
1.27
1.27
1.27
0.64
T
0.35 ±0.10
0.35 ±0.10
0.40 ±0.15
0.375 ±0.125
0.45 ±0.10
0.525 ±0.175
0.55 ±0.15
0.525 ±0.175
0.525 ±0.175
0.575 ±0.125
0.575 ±0.125
0.60 ±0.10
0.60 ±0.10
0.60 ±0.10
A
N/A
N/A
0.30 ±0.15
0.29 ±0.11
0.30 ±0.10
0.50 ±0.15
0.45 ±0.20
0.50 ±0.15
0.50 ±0.15
0.60 ±0.15
0.60 ±0.15
0.95 ±0.20
0.95 ±0.20
0.35 ±0.05
B
0.175 ±0.125
0.20 ±0.15
0.20 ±0.15
0.20 ±0.10
0.30 ±0.15
0.30 ±0.20
0.30 ±0.20
0.30 ±0.20
0.30 ±0.20
0.50 ±0.30
0.50 ±0.30
0.50 ±0.15
0.50 ±0.15
0.30 ±0.15
C
0.15 ±0.10
0.25 ±0.10
0.25 ±0.20
0.265 ±0.115
0.375 ±0.175
0.40 ±0.15
0.275 ±0.175
0.35 ±0.20
0.40 ±0.15
0.55 ±0.30
0.55 ±0.30
0.50 ±0.15
0.50 ±0.15
0.35 ±0.15
D
0.35 ±0.10
0.33 ±0.15
0.40 ±0.15
N/A
0.325 ±0.175
N/A
0.525 ±0.225
N/A
N/A
N/A
N/A
1.10 ±0.15
1.10 ±0.15
0.45 ±0.05
2
2
4
4
8
2
4
4
8
8
8
8
8
8
DOC# 008-0335-0 Rev. P
Page 5 of 11
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
聊聊、笑笑、闹闹
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
