电子工程世界电子工程世界电子工程世界

关键词

搜索

型号

搜索

WBDDQSC-A-05-9200-B-A

产品描述Array/Network Resistor, Isolated, 0.1W, 920ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 1109,
产品类别无源元件    电阻器   
文件大小273KB,共4页
制造商TT Electronics plc
官网地址http://www.ttelectronics.com/
下载文档 详细参数 全文预览

WBDDQSC-A-05-9200-B-A概述

Array/Network Resistor, Isolated, 0.1W, 920ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 1109,

WBDDQSC-A-05-9200-B-A规格参数

参数名称属性值
Objectid803005977
Reach Compliance Codecompliant
ECCN代码EAR99
构造Chip
网络类型Isolated
端子数量24
最高工作温度150 °C
最低工作温度-55 °C
封装高度0.406 mm
封装长度2.921 mm
封装形式SMT
封装宽度2.184 mm
包装方法Tray
额定功率耗散 (P)0.1 W
参考标准MIL-PRF-38534
电阻920 Ω
电阻器类型ARRAY/NETWORK RESISTOR
系列WBC-NETWORK
尺寸代码1109
温度系数100 ppm/°C
容差0.1%
工作电压100 V

文档预览

下载PDF文档
Wire Bondable
Resistor Network Arrays
Chip Network Array Series
·
·
·
·
Absolute tolerances to ±0.1%
Tight TCR tracking to ±5ppm/°C
Ratio match tolerances to ±0.05%
Ultra-stable tantalum nitride resistors
IRC’s TaNSil
®
network array resistors are ideally suited for applications that demand a small footprint. The small wire
bondable chip package provides higher component density, lower resistor cost and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking and low cost.
Excellent performance in harsh, humid environments is a trademark of IRC’s self-passivating TaNSil
®
resistor film.
For applications requiring high performance resistor networks in a low cost, wire bondable package, specify IRC
network array die.
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
10. 11
发个图,求教最简单的AD例子
是否只要按合适的时间间隔,对ADON置1,就可完成AD?有何其他条件?向大家求教。...
shizhu72 stm32/stm8
有没有用过TLC3574的大侠?
小弟现在用TI的一个14位的AD,TLC3574,用一个ARM控制它,用JLink在线调试,我的ARM和TLC3574用光耦完全隔离开了,问题是ARM没有运行的时候板子的电压正常,但是一旦程序运行起来,tlc3574那一块 ......
wangtong0819 嵌入式系统
求一个2位数码管显示45分钟单片机程序,要C语言版
题目:秒表设计 用89C2051单片机,外接12MHZ晶振、1个双LED数码管、上电显示15分钟,0—45分钟调节,5个按键, 具体要求如下: 1.1位双LED数码管右边1位显示秒,左边1位 ......
liu2006hui 编程基础
转载 PCB设计流程(新手必备)
一般PCB基本设计流程如下:前期准备->PCB结构设计->PCB布局->布线->布线优化和丝印->网络和DRC检查和结构检查->制版。   第一:前期准备。这包括准备元件库和原理图。“工欲善其事,必先利其 ......
抛砖引玉 模拟电子
mosfet陡化前沿超调量问题
256497 原理图大致如下 256498 仿真结果如图 256499 实际测量各部分波形大致如图 根据设计要求,产生的陡前沿方波tr小于60ns,ts(10%Uo-Uo±0.03Uo)小于200ns 实际产生的方波会有一 ......
度假的乞丐 模拟电子

 
EEWorld订阅号

 
EEWorld服务号

 
汽车开发圈

 
机器人开发圈

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版

站点相关: 大学堂 TI培训 Datasheet 电子工程 索引文件: 1146  2642  2513  2302  1817  24  54  51  47  37 

器件索引   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

北京市海淀区中关村大街18号B座15层1530室 电话:(010)82350740 邮编:100190

电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved