Datasheet> 器件分类 > 半导体> 其他集成电路（IC）> IS49NLC18320-25BLI

IS49NLC18320-25BLI: 产品描述dram 576mbit x18 common I/O 400mhz RLdram2; 产品类别半导体其他集成电路（IC）; 文件大小531KB，共34页; 制造商All Sensors; 标准

下载文档详细参数全文预览

IS49NLC18320-25BLI在线购买

供应商	器件名称	价格	最低购买	库存
	IS49NLC18320-25BLI	-	-	点击查看	点击购买

IS49NLC18320-25BLI概述

dram 576mbit x18 common I/O 400mhz RLdram2

IS49NLC18320-25BLI规格参数

参数名称	属性值
Manufacture	ISSI
产品种类 Product Category	DRAM
RoHS	Yes
Data Bus Width	18 bi
Organizati	32 M x 18
封装 / 箱体 Package / Case	BGA-144
Memory Size	576 Mbi
Maximum Clock Frequency	400 MHz
Access Time	2.5 ns
电源电压-最大 Supply Voltage - Max	1.9 V
Supply Voltage - Mi	1.7 V
Maximum Operating Curre	408 mA
最大工作温度 Maximum Operating Temperature	+ 85 C
系列 Packaging	Tray
最小工作温度 Minimum Operating Temperature	- 40 C
安装风格 Mounting Style	SMD/SMT
工厂包装数量 Factory Pack Quantity	104

文档预览

下载PDF文档

全文
预览

IS49NLC96400,IS49NLC18320,IS49NLC36160

576Mb (x9, x18, x36) Common I/O RLDRAM

2 Memory

FEATURES

•

400MHz DDR operation (800Mb/s/pin data rate)

28.8Gb/s peak bandwidth (x36 at 400 MHz clock

frequency)

Reduced cycle time (15ns at 400MHz)

32ms refresh (16K refresh for each bank; 128K refresh

command must be issued in total each 32ms)

8 internal banks

Non-multiplexed addresses (address multiplexing option

available)

SRAM-type interface

Programmable READ latency (RL), row cycle time, and

burst sequence length

Balanced READ and WRITE latencies in order to optimize

data bus utilization

Data mask signals (DM) to mask signal of WRITE data; DM

is sampled on both edges of DK.

Package:

−

144-ball FBGA (leaded)

−

144-ball FBGA (lead-free)

Configuration:

−

64Mx9

−

32Mx18

−

16Mx36

Clock Cycle Timing:

•

Differential input clocks (CK, CK#)

Differential input data clocks (DKx, DKx#)

On-die DLL generates CK edge-aligned data and output

data clock signals

Data valid signal (QVLD)

HSTL I/O (1.5V or 1.8V nominal)

25-60Ω matched impedance outputs

2.5V V

EXT

, 1.8V V

, 1.5V or 1.8V V

DDQ

I/O

On-die termination (ODT) R

IEEE 1149.1 compliant JTAG boundary scan

Operating temperature:

Commercial

= 0° to +95°C; T

= 0°C to +70°C),

Industrial

= -40°C to +95°C; T

= -40°C to +85°C)

DECEMBER 2012

•

OPTIONS

•

Speed Grade

-25E

2.5

-25

2.5

-33

3.3

-5

Unit

notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the

latest version of this device specification before relying on any published information and before placing orders for products.

Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can

reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such

applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:

a.) the risk of injury or damage has been minimized;

b.) the user assume all such risks; and

c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances

RLDRAM

is a registered trademark of Micron Technology, Inc.

Integrated Silicon Solution, Inc. – www.issi.com –

Rev. 00F, 12/4/2012

IS49NLC96400,IS49NLC18320,IS49NLC36160

1.4 Ball Descriptions

Symbol

BA*

CK, CK#

CS#

DQ*

Type

Input

I/O

Description

Address inputs: Defines the row and column addresses for READ and WRITE operations. During a MODE

CK.

Bank address inputs: Selects to which internal bank a command is being applied to.

Input clock: CK and CK# are differential input clocks. Addresses and commands are latched on the rising

edge of CK. CK# is ideally 180 degrees out of phase with CK.

Chip select: CS# enables the command decoder when LOW and disables it when HIGH. When the

command decoder is disabled, new commands are ignored, but internal operations continue.

Data input: The DQ signals form the data bus. During READ commands, the data is referenced to both

edges of QK*. During WRITE commands, the data is sampled at both edges of DK.

Input data clock: DK* and DK*# are the differential input data clocks. All input data is referenced to

both edges of DK*. DK*# is ideally 180 degrees out of phase with DK*. For the x36 device, DQ0–DQ17

are referenced to DK0 and DK0# and DQ18–DQ35 are referenced to DK1 and DK1#. For the x9 and x18

devices, all DQ* are referenced to DK and DK#. All DK* and DK*# pins must always be supplied to the

device.

Input data mask: The DM signal is the input mask signal for WRITE data. Input data is masked when DM

is sampled HIGH. DM is sampled on both edges of DK (DK1 for the x36 configuration). Tie signal to

ground if not used.

IEEE 1149.1 clock input: This ball must be tied to V

if the JTAG function is not used.

IEEE 1149.1 test inputs: These balls may be left as no connects if the JTAG function is not used.

Command inputs: Sampled at the positive edge of CK, WE# and REF# define (together with CS#) the

command to be executed.

Input reference voltage: Nominally V

DDQ

/2. Provides a reference voltage for the input buffers.

External impedance (25–60Ω): This signal is used to tune the device outputs to the system data bus

impedance. DQ output impedance is set to 0.2 × RQ, where RQ is a resistor from this signal to ground.

Connecting ZQ to GND invokes the minimum impedance mode.

Output data clocks: QK* and QK*# are opposite polarity, output data clocks. They are free running, and

during READs, are edge-aligned with data output from the memory. QK*# is ideally 180 degrees out of

phase with QK*. For the x36 device, QK0 and QK0# are aligned with DQ0-DQ17, and QK1 and QK1# are

aligned with DQ18-DQ35. For the x18 device, QK0 and QK0# are aligned with DQ0-DQ8, while QK1 and

QK1# are aligned with Q9-Q17. For the x9 device, all DQs are aligned with QK0 and QK0#.

Data valid: The QVLD pin indicates valid output data. QVLD is edge-aligned with QK* and QK*#.

IEEE 1149.1 test output: JTAG output. This ball may be left as no connect if the JTAG function is not

used.

Power supply: Nominally, 1.8V.

DQ power supply: Nominally, 1.5V or 1.8V. Isolated on the device for improved noise immunity.

Power supply: Nominally, 2.5V.

Ground.

DQ ground: Isolated on the device for improved noise immunity.

Power supply: Isolated termination supply. Nominally, V

DDQ

/2.

Reserved for future use: This signal is not connected and can be connected to ground.

Do not use: These balls may be connected to ground. Note that if ODT is enabled, these pins are High-Z.

No function: These balls can be connected to ground.

DK*, DK*#

Input

TCK

TMS,TDI

WE#, REF#

REF

Input

I/O

QK*, QK*#

QVLD

TDO

DDQ

EXT

SSQ

A22

DNU

Output

Supply

Integrated Silicon Solution, Inc. – www.issi.com –

Rev. 00F, 12/4/2012

推荐资源

下图是话筒放大，怎么介入立体上音源接口啊？: 来自：电子工程师技术交流(12425841)56359...; 一棵小小草模拟电子

Stellaris怕是要称为历史名词了: 现在貌似在TI的官网上已经看不到 Stellaris的提法。取而代之的是Tiva系列和TivaWare软件包。你们怎么看？...; zca123 微控制器 MCU

51汇编语言指令集下载！: 51汇编语言指令集很多书上有，但是有很多书没有放在一起，每章一部分。还有些朋友有书没带在身边，或是使用过，望了买本书又划不来。把这个传上来方便各位。...; single 51单片机

资料先行：ST最新STML5产品开发板NUCLEO-L552ZE-Q（Cortex-M33内核）: 开发板： NUCLEO-L552ZE-Q 511439 采用STM32L552ZE MCU和SMPS的STM32 Nucleo-144开发板，支持Arduino、ST Zio和morpho连接。 STM32L5 系列将高性能、安全性和低功耗集于一身，内置运行 ......; EEWORLD社区 stm32/stm8

FPGA开发流程.: 482638 ...; 至芯科技FPGA大牛 FPGA/CPLD

关于WINCE上的SKYPE给小弟一点帮助呀: 是这样的，我想在windows ce上的运行SKYPE程序？哪位兄弟有没有移植好的EXE文件，或者源码呀，能不能给我一份呀？小弟不胜感谢！我的邮箱是sunboyljp@163.com...; hilltree 嵌入式系统

器件捷径: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

热门器件

开源项目推荐更多

热门活动更多

热门文章更多

技术资料推荐更多