REVISIONS
LTR
A
DESCRIPTION
Add device types 05 and 06. Correct coupling digram, figure 4. Add
common mode input voltage and test circuit. Table I, change I
SIH
.
Editorial changes throughout.
Changes made in accordance with 5962-R034-92.
Update drawing to the latest requirements. -sld
Added device type 07. -sld
Added device type 08. -sld
DATE (YR-MO-DA)
91-05-17
APPROVED
W. Heckman
B
C
D
E
91-11-06
05-08-24
06-05-25
09-02-04
Gregory Lude
Raymond Monnin
Raymond Monnin
Robert M. Heber
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
E
15
E
16
E
17
REV
SHEET
E
1
E
2
E
3
E
4
E
5
E
6
E
7
E
8
E
9
E
10
E
11
E
12
E
13
E
14
PREPARED BY
Donald R. Osborne
CHECKED BY
Ray Monnin
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil/
APPROVED BY
Michael Frye
MICROCIRCUIT, HYBRID, DIGITAL, LOW
POWER, SINGLE CHANNEL, DRIVER-
RECEIVER
SIZE
A
SHEET
CAGE CODE
DRAWING APPROVAL DATE
20 JUNE 1989
REVISION LEVEL
E
67268
1 OF
17
5962-89592
DSCC FORM 2233
APR 97
5962-E077-09
1. SCOPE
1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to processed in accordance with
MIL-PRF-38534.
1.2 PIN. The PIN shall be as shown in the following example:
5962-89592
Drawing number
01
Device type
(see 1.2.1)
X
Case outline
(see 1.2.2)
X
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01 and 03
02 and 04 1/
05
06
07
08
Generic number
ARX3407
ARX3404
ARX3467
ARX3464
ACT4406N
ACT4404N
Circuit function
Single channel, driver-receiver (MIL-STD-1553 A and B) low
power, receiver standby high
Single channel, driver-receiver (universal transceiver) low
power, receiver standby high
Single channel, driver-receiver (MIL-STD-1553 A and B) low
power, receiver standby low
Single channel, driver-receiver (universal transceiver) low
power, receiver standby low
Single channel, driver-receiver (universal transceiver) low
power, receiver standby high
Single channel, driver-receiver (universal transceiver) low
power, receiver standby low
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Y
Descriptive designator
See figure 1
See figure 1
Terminals
24
24
Package style
Hybrid package
Flat package
1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 2/
Supply voltage ranges:
V
CC
....................................................................................
V
EE
....................................................................................
+5 V supply.......................................................................
Logic input voltage range.......................................................
Receiver differential input voltage..........................................
Receiver common mode input voltage range ........................
Driver peak output current .....................................................
Storage temperature range....................................................
Lead temperature (soldering, 10 seconds) ............................
Junction temperature (T
J
) ......................................................
1/
2/
-0.3 V dc to +18 V dc
+0.3 V dc to - 18 V dc
-0.3 V dc to +7 V dc
-0.3 V dc to +5.5 V dc
40 Vp-p
-10 V to +10 V
300
mA
-65C to +150C
+300C
+160C
The device types 02 and 04 are no longer available, device type 07 can be used as a substitute.
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
E
5962-89592
SHEET
2
DSCC FORM 2234
APR 97
Power dissipation (P
D
) total hybrid:
100 percent duty cycle (T
C
= +25C):
Device types 01, 03, and 05........................................
Device types 02, 04, 06, 07, and 08............................
Standby mode, all devices....................................................
Power dissipation (P
D
) hottest die:
100 percent duty cycle:
Device types 01, 03, and 05 .........................................
Device types 02, 04, 06 ................................................
Standby mode, all devices ...............................................
Thermal resistance:
Junction-to-case (
JC
) hottest die:
Device types 01, 02, 05, and 06 ...................................
Device types 03 and 04 ................................................
Device types 07 and 08 ................................................
Case-to-ambient, all devices .................................................
Maximum junction-to-case temperature rise for the
hottest die at 100 percent duty cycle:
Device types 01 and 05 ................................................
Device types 02 and 06 ................................................
Device type 03 ..............................................................
Device type 04 ..............................................................
Device types 07 and 08 ................................................
1.4 Recommended operating conditions.
Supply voltage ranges:
V
CC
....................................................................................
V
EE
....................................................................................
+5 V supply.......................................................................
Logic input voltage range.......................................................
Receiver differential voltage ..................................................
Receiver common mode voltage range ................................
Driver peak output current:
Device types 01, 02, 05, 06, 07, and 08 ......................
Device types 03 and 04 ................................................
Maximum serial data rate.......................................................
Case operating temperature range (T
C
).................................
2. APPLICABLE DOCUMENTS
3.0 W
3.24 W
1.06 W
484 mW 1/ 2/
545 mW 2/ 3/
Derates to zero
88C/W
58C/W
5C/W
21C/W
42.6C
47.9C
28C
31.6C
16.25C
+11.4 V dc to +15.75 V dc
-11.4 V dc to -15.75 V dc
+4.5 V dc to +5.5 V dc
0 V dc to +5.0 V dc
40 Vp-p
-10 V to +10 V
180
mA
120
mA
1.0 MHz
-55C to +125C
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
1/ Duty cycle at 1.0 MHz for device types 01 and 05. Derate to 82 percent maximum at T
C
= +125C for a maximum
junction temperature of +160C in the hottest die.
2/ Duty cycle for device types 03, 04, 07, and 08 needs no derating over the full operating temperature range.
3/ Duty cycle at 1.0 MHz for device types 02 and 06. Derate to 73 percent maximum at T
C
= +125C for a maximum
junction temperature of +160C in the hottest idie.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
E
5962-89592
SHEET
3
DSCC FORM 2234
APR 97
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Test circuit. The test circuit shall be as specified on figure 3.
3.2.4 Timing waveforms. The timing waveforms shall be as specified in figure 4.
3.2.5 Coupling diagram. The coupling digram shall be as specified in figure 5.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked
with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot
sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for
those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer
and be made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
E
5962-89592
SHEET
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55C
T
C
+125C
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Max
Unit
Receiver
Output low voltage
V
OL
I
OL
= 10 mA
I
OL
= 4 mA
Output high voltage
Differential input voltage level
Common mode input voltage
range
Differential input impedance
Input capacitance
Threshold voltage
V
OH
V
I
V
ICR
1 MHz sine wave
See figure 3
1 MHz sine wave
1 MHz sine wave 2/
3/ 4/
I
OH
= -0.4 mA
1,2,3
4,5,6
4,5,6
1,2,3
01-06
07,08
All
All
All
10
2.5
40
V
Vp-p
Vp-p
0.5
V
Z
IN
C
IN
V
TH
4,5,6
4
4,5,6
All
All
01-06
07,08
10
5
0.6
0.6
1.05
1.10
450
k
pF
Vp-p
Receiver delay
t
DR
Input zero crossing 2/
to DATA or
DATA
, see
figure 4
9,10,11
All
ns
Receiver strobe
Input low voltage
V
SIL
1,2,3
All
0.7
V
Input high voltage
V
SIH
1,2,3
All
2.0
V
Input low current
I
SIL
V
SIL
= 0.4 V
1,2,3
All
-0.4
mA
Input high current
I
SIH
V
SIH
= 2.7 V
1,2,3
All
80
A
Strobe delay
t
DS
Turn-on or turn-off, 2/
see figure 4
9,10,11
All
200
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
E
5962-89592
SHEET
5
DSCC FORM 2234
APR 97
微控制器 MCU
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
