1. Calculated using MIL-HDBK-217F with nominal input voltage at full load.
2. Supply voltage must be discontinued at the end of the short circuit duration.
All specifications typical at T
A
=25°C, nominal input voltage and rated output current unless otherwise specified.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
All enquiries: www.murata-ps.com/support
KDC_NMVC2.G01
Page 1 of 4
NMV 24V & 48V Series
3kVDC Isolated 1W Single & Dual Output DC/DC Converters
ABSOLUTE MAXIMUM RATINGS
Short-circuit protection
2
Lead temperature 1.5mm from case for 10 seconds
Input voltage V
IN
, NMV24 types
Input voltage V
IN,
NMV48 types
1 second
300°C
28V
54V
OUTPUT CHARACTERISTICS
Parameter
Rated Power
Voltage Set Point Accuracy
Line regulation
1
Conditions
T
A
=0
°C
to 70
°C
See tolerance envelope
High V
IN
to low V
IN
Min.
Typ.
Max.
1
1.2
Units
W
%/%
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Conditions
Flash tested for 1 minute
Viso= 1000VDC
Min.
3000
1
Typ.
Max.
Units
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
All input types
Min.
Typ.
100
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Specification
Storage
Cooling
Conditions
All output types
Free air convection
Min.
0
-55
Typ.
Max.
70
150
Units
°C
TEMPERATURE DERATING GRAPH
1.5
TOLERANCE ENVELOPE
+10%
70°C
+5%
V
NOM
Output Power (W)
Typical
Lo
1.0
0.5
0
ad Line
+2.5%
-2.5%
-7.5%
Safe Operating
Area
0
150
50
100
Ambient Temperature (°C)
Output Voltage
10
75
50
25
Output Load Current (%)
100
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMV series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 3kVDC for 1 minute.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specific agency approvals, such as the NMV series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMV series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com
All enquiries: www.murata-ps.com/support
KDC_NMVC2.G01
Page 2 of 4
NMV 24V & 48V Series
3kVDC Isolated 1W Single & Dual Output DC/DC Converters
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
DIP package
0.386
(9.80)
0.77 (19.50)
SIP package
0.77 (19.50)
0.236
(6.00)
††
NMV2405DC
XYYWWi
0.268
(6.80)
†
0.181 (4.60)
0.142 (3.60)
0.394
(10.00)
NMV2415SC
XYYWWi
0.0216 (0.55)
0.0177 (0.45)
1 2
0.022 (0.55)
0.018 (0.45)
0.1 (2.54)
0.043
(1.09)
0.3
(7.62)
0.084
(2.13)
0.303 (7.70) for 48V variants
0.300 (7.50) for 48V variants
* Pin not fitted on single output variants.
All dimensions in inches ±0.01 (mm ±0.25mm). All pins on a 0.1 (2.54) pitch and within ±0.01 (0.25) of true position.
5 6* 7
0.0216 (0.55)
0.0177 (0.45)
0.181 (4.60)
0.142 (3.60)
0.1 (2.54)
1
14
7
10 9* 8
0.6 (15.24)
0.118 (0.30)
0.0079 (0.20)
0.049 (1.25)
0.074±0.02 (1.88±0.50)
0.0118 (0.30)
0.0079 (0.20)
0.6 (15.24)
Weight: 2.11g (DIP and SIP)
PIN CONNECTIONS
Single output variants
14 Pin DIP
Pin
Function
1
7
8
10
14
-V
IN
NC
+V
OUT
-V
OUT
+V
IN
Dual output variants
14 Pin DIP
Pin
Function
1
7
8
9
10
14
-V
IN
NC
+V
OUT
OV
-V
OUT
+V
IN
7 Pin SIP
Pin
Function
1
2
5
7
+V
IN
-V
IN
-V
OUT
+V
OUT
7 Pin SIP
Pin
Function
1
2
5
6
7
+V
IN
-V
IN
-V
OUT
OV
+V
OUT
www.murata-ps.com
All enquiries: www.murata-ps.com/support
KDC_NMVC2.G01
Page 3 of 4
NMV 24V & 48V Series
3kVDC Isolated 1W Single & Dual Output DC/DC Converters
PACKAGE SPECIFICATIONS (continued)
RECOMMENDED FOOTPRINT DETAILS
14 Pin DIP Package
7 Pin SIP Package
*Hole not required for single output variants.
TUBE OUTLINE DIMENSIONS
14 Pin DIP Tube
7 Pin SIP Tube
Unless otherwise stated all dimensions in inches (mm) ±0.5mm.
Tube length (14 Pin DIP) : 20.47 (520mm ±2mm).
Tube length (7 Pin SIP) : 20.47 (520mm ±2mm).
Tube Quantity : 25
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish
on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types
in this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
This product is subject to the following
operating requirements
and the
Life and Safety Critical Application Sales Policy:
Refer to:
http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
