where an unpowered on state is critical in a single
control line SPDT terminated switch.
The
unpowered condition is the same as the V
C
= 0
condition. This part can also be configured as a
reflective switch with minimal impact to the RF
performance.
The MASWSS0201 delivers high isolation, low
insertion loss and high linearity up to 2.5 GHz.
The MASWSS0201 is fabricated using a 0.5 micron
gate length GaAs E/D PHEMT process.
The
process features full passivation for performance
and reliability.
GND
N/C
GND
Pin Configuration
2
Pin No.
1
2
3
4
5
6
7
8
9
10
Pin Name
N/C
RF1
Term 1 GND
3
GND
N/C
GND
Term 2 GND
RF2
VC
GND
RFC
GND
Paddle
4
3
Description
No Connection
RF Port 1
Termination 1 Ground
Ground
No Connection
Ground
Termination 2 Ground
RF Port 2
Control
Ground
RF Input
Ground
RF and DC Ground
Ordering Information
1
Part Number
MASWSS0201TR-3000
MASWSS0201SMB
11
Package
3000 piece reel
Sample Test Board
(Includes 5 Samples)
12
13
1. Reference Application Note M513 for reel size information.
2. M/A-COM recommends that all unused (N/C) pins be
connected to ground. All data on this datasheet was taken
with N/C pins connected to ground.
3. Terminated grounds require DC blocking capacitors; see
application schematic.
4. The exposed pad centered on the package bottom must be
connected to RF and DC ground.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
5. Electrical specifications apply to terminated configuration only.
Absolute Maximum Ratings
6,7
Parameter
Input Power @ 100 MHz
Input Power @ 1 GHz
Operating Voltage
Operating Temperature
Storage Temperature
Truth Table
8,9,10
Control V
C
0
1
Absolute Maximum
+22 dBm
+29 dBm
+8.5 volts
-40
°
C to +85
°
C
-65
°
C to +150°C
RFC-RF1
On
Off
RFC-RF2
Off
On
8. External DC blocking capacitors are required on all RF ports.
9. 0 = 0 ± 0.1 V, 1 = +2.9 V to +5 V.
10. The unpowered on state is the same as V
C
=0.
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
M/A-COM’s AN3007 Application Note outlines a
method for ESD sensitivity mitigation. It can be
found at the Tech/Apps section of the
MACOM.COM website.
11. Non-connected pins (P1 and P5) are shown connected to
ground as recommended. All data on this datasheet was
taken with N/C pins connected to ground.
12. Application schematic shown is for terminated
configuration. For non-terminated operation Term 1 and
Term 2 ground pins are left open. See application section
for data in unterminated configuration.
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
FPGA/CPLD
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
