Not for New Design
Type 730P
Vishay Sprague
Film Capacitors
High Frequency, Wrap-and-Fill, Metallized Polypropylene
FEATURES
•
Excellent AC performance
•
Low Power dissipation
•
Low dielectric absorption
•
Close tolerance
•
High stability
PERFORMANCE CHARACTERISTICS
Operating Temperature:
- 55 °C to + 85 °C
Voltage derating:
At + 105 °C, 50 % of + 85 °C rating
ESR:
20 kHz to 100 kHz
Capacitance Range:
0.022 µF to 10.0 µF
Capactiance Tolerance:
± 20 %, ± 10 %, ± 5 %
DC Voltage Rating:
100 WVDC to 630 WVDC
AC Voltage Rating:
70 Vrms to 275 Vrms, 60 Hz to 400 Hz
Dissipation Factor:
0.1 % maximum
Measure all units at 1000 Hz at + 25 °C
DC Voltage Test:
200 % of rated voltage for 2 minutes
AC Voltage Test:
130 % of rated rms voltage at 60 Hz for
15 seconds
Insulation Resistance:
Measured at 100 WVDC after a
2 minute charge.
At + 25 °C: 200 000 Megohm - Microfarads
or 400 000 Megohm minimum.
At + 85 °C: 10 000 Megohm - Microfarads
or 20 000 Megohm minimum.
At + 105 °C: 1000 Megohm - Microfarads
or 2000 Megohm minimum.
Vibration Test (Condition B):
No mechanical damage,
short, open or intermittent circuits.
AC Life Test:
110 % of rated rms voltage at 60 Hz for 1000
hours at + 85 °C.
Maximum
Δ
CAP ± 5 %
Minimum IR = 50 % of initial limit
Maximum DF = 0.12 %
DC Life Test:
150 % of rated voltage for 1000 hours
at + 85 °C. No open or short circuits. No visible damage.
Maximum
Δ
CAP ± 1.0 %
Minimum IR = 50 % of initial limit
Maximum DF = 0.12 %
Humidity Test:
95 % relative humidity at + 40 °C for 250
hours. No visible damage.
Maximum
Δ
CAP ± 1.0 %
Minimum IR = 20 % of initial limit
Maximum DF = 0.12 %
PHYSICAL CHARACTERISTICS
Lead Pull:
5 pounds (2.3 kilograms) for one minute. No
physical damage.
Lead Bend:
After three complete consecutive bends. No
damage.
Marking:
Sprague
®
trademark, type or part number,
capacitance and voltage.
DIMENSIONS
in inches [millimeters]
1.750
[44.45]
Min.
L
±
0.062 [1.57]
1.750
[44.45]
Min.
D
Max.
Solid Tinned Wire
0.032 [0.81] Nominal Dia.
(No. 20 AWG)
* Leads to be within 0.062" [1.57 mm] of center line at egrees but not less than 0.031" [0.79 mm] from edge.
Document Number: 42029
Revision: 07-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
25
Not for New Design
Type 730P
Vishay Sprague
Film Capacitors
High Frequency, Wrap-and-Fill,
Metallized Polypropylene
MAXIMUM RIPPLE CURRENT
ESR
(Amps rms) at 20 kHz
(Milliohms)
Case Temperature*** at
20 kHz -
100 Khz
+ 25 °C + 35 °C + 45 °C + 55 °C + 65 °C + 75 °C + 85 °C
100 WVDC
-
Not applicable. These capacitance values are not customarily
-
used in switched-mode power supplies.
-
-
-
-
-
-
-
-
-
37.0
3.7
3.4
3.1
2.8
2.5
2.0
1.4
35.0
3.9
3.6
3.3
2.9
2.6
2.1
1.5
33.0
4.1
3.8
3.5
3.1
2.8
2.2
1.6
31.0
4.3
4.0
3.6
3.2
2.9
2.3
1.7
26.0
5.5
5.1
4.7
4.2
3.6
2.8
2.6
24.0
5.7
5.3
4.9
4.4
3.8
3.0
2.8
20.0
6.1
5.5
5.1
4.6
4.0
3.2
3.1
19.0
6.3
5.7
5.3
4.8
4.1
3.4
3.0
18.0
6.5
6.0
5.5
4.9
4.2
3.5
3.2
18.0
6.8
6.3
5.7
5.1
4.4
3.6
3.3
17.0
7.1
6.5
6.0
5.3
4.6
3.7
3.4
16.0
7.3
6.7
6.2
5.5
4.8
3.9
3.5
16.0
7.4
6.8
6.4
5.6
4.9
4.0
3.6
15.0
7.6
6.9
6.6
5.8
5.1
4.1
3.7
15.0
7.8
7.0
6.7
5.9
5.2
4.2
3.8
15.0
8.1
7.4
6.8
6.0
5.3
4.3
3.9
14.0
8.3
7.6
7.0
6.2
5.4
4.4
4.0
14.0
8.4
7.7
7.1
6.4
5.5
4.5
4.1
14.0
8.5
7.8
7.2
6.5
5.6
4.6
4.2
13.0
8.5
8.0
7.4
6.7
5.7
4.7
4.3
13.0
8.6
8.3
7.7
6.8
6.0
4.8
4.4
13.0
8.8
8.6
8.0
7.0
6.1
4.9
4.5
12.0
9.0
9.0
8.5
7.6
6.6
5.4
4.9
250 WVDC
-
-
-
Not applicable. These capacitance values are not customarily
-
used in switched-mode power supplies.
-
-
-
-
-
-
-
-
-
-
-
35.0
3.8
3.7
3.6
3.4
2.9
2.4
1.7
33.0
3.9
3.8
3.7
3.5
3.1
2.5
1.8
32.0
4.0
3.9
3.8
3.7
3.2
2.6
1.9
31.0
4.2
4.1
4.0
3.9
3.4
2.8
2.0
28.0
4.4
4.4
4.4
4.4
4.3
3.5
3.2
27.0
4.7
4.6
4.5
5.0
4.5
3.7
3.3
26.0
5.1
5.0
4.9
5.4
4.7
3.9
3.5
25.0
5.9
5.8
5.7
5.7
5.0
4.1
3.7
21.0
7.2
7.2
6.8
6.0
5.2
4.3
3.9
20.0
8.4
7.5
7.0
6.3
5.4
4.5
4.1
19.0
8.6
7.8
7.3
6.6
5.7
4.7
4.3
18.0
9.0
8.3
7.6
6.8
5.9
4.8
4.4
18.0
9.0
8.4
7.8
7.0
6.0
4.9
4.5
17.0
9.0
8.5
8.0
7.2
6.2
5.0
4.6
16.0
9.0
8.6
8.2
7.4
6.3
5.1
4.7
16.0
9.0
8.8
8.5
7.7
6.6
5.3
4.9
15.0
9.0
9.0
8.8
7.9
6.8
5.6
5.1
15.0
9.0
9.0
8.9
8.0
7.0
5.8
5.3
15.0
9.0
9.0
9.0
8.2
7.2
5.9
5.5
15.0
9.0
9.0
9.0
8.4
7.4
6.0
5.6
14.0
9.0
9.0
9.0
8.7
7.8
6.3
5.8
14.0
9.0
9.0
9.0
8.8
7.9
6.4
5.9
13.0
9.0
9.0
9.0
8.9
8.3
6.8
6.2
STANDARD RATINGS
in inches [millimeters]
CAPACITANCE
(µF)
PART NUMBER**
0.22
0.27
0.33
0.39
0.47*
0.56
0.68
0.82
1.0*
1.2
1.5
1.8
2.0
2.2
2.7
3.0
3.3
3.9
4.0
4.7
5.0
5.6
6.0
6.8
8.0
8.2
10.0
730P224X9100
730P274X9100
730P334X9100
730P394X9100
730P474X9100
730P564X9100
730P684X9100
730P824X9100
730P105X9100
730P125X9100
730P155X9100
730P185X9100
730P205X9100
730P225X9100
730P275X9100
730P305X9100
730P335X9100
730P395X9100
730P405X9100
730P475X9100
730P505X9100
730P565X9100
730P605X9100
730P685X9100
730P805X9100
730P825X9100
730P106X9100
CASE SIZE
D
L
0.275 [7.0]
0.298 [7.6]
0.324 [8.2]
0.347 [8.8]
0.376 [9.6]
0.321 [8.2]
0.348 [8.8]
0.377 [9.6]
0.421 [10.7]
0.454 [11.5]
0.500 [12.7]
0.541 [13.7]
0.486 [12.3]
0.507 [12.9]
0.554 [14.1]
0.581 [14.8]
0.606 [15.4]
0.654 [16.6]
0.537 [13.6]
0.577 [14.7]
0.593 [15.1]
0.624 [15.8]
0.644 [16.4]
0.682 [17.3]
0.735 [18.7]
0.743 [18.9]
0.815 [20.7]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
0.1*
730P104X9250
0.279 [7.1] 0.75 [19.0]
0.12
730P124X9250
0.300 [7.6] 0.75 [19.0]
0.15
730P154X9250
0.327 [8.3] 0.75 [19.0]
0.18
730P184X9250
0.353 [9.0] 0.75 [19.0]
0.22*
730P224X9250
0.306 [7.8] 1.00 [25.4]
0.27
730P274X9250
0.333 [8.5] 1.00 [25.4]
0.33*
730P334X9250
0.362 [9.2] 1.00 [25.4]
0.39
730P394X9250
0.389 [9.9] 1.00 [25.4]
0.47*
730P474X9250 0.422 [10.7] 1.00 [25.4]
0.56
730P564X9250 0.464 [11.8] 1.00 [25.4]
0.68
730P684X9250 0.425 [10.8] 1.25 [31.8]
0.82
730P824X9250 0.471 [12.0] 1.25 [31.8]
1.0*
730P105X9250 0.513 [13.0] 1.25 [31.8]
1.2
730P125X9250 0.554 [14.1] 1.25 [31.8]
1.5
730P155X9250 0.613 [15.6] 1.25 [31.8]
1.8
730P185X9250 0.667 [17.0] 1.25 [31.8]
2.0*
730P205X9250 0.700 [17.8] 1.25 [31.8]
2.2
730P225X9250 0.610 [15.5] 1.75 [44.5]
2.7
730P275X9250 0.669 [17.0] 1.75 [44.5]
3.0
730P305X9250 0.703 [17.9] 1.75 [44.5]
3.3
730P335X9250 0.734 [18.6] 1.75 [44.5]
3.9
730P395X9250 0.794 [20.2] 1.75 [44.5]
4.0
730P405X9250 0.803 [20.4] 1.75 [44.5]
4.7
730P475X9250 0.866 [22.0] 1.75 [44.5]
5.0
730P505X9250 0.892 [22.7] 1.75 [44.5]
5.6
730P565X9250 0.941 [23.9] 1.75 [44.5]
6.0
730P605X9250 0.972 [24.7] 1.75 [44.5]
6.8
730P685X9250 0.882 [22.4] 2.25 [57.2]
8.0
730P805X9250 0.953 [24.2] 2.25 [57.2]
8.2
730P825X9250 0.964 [24.5] 2.25 [57.2]
10.0
730P106X9250 1.060 [26.9] 2.25 [57.2]
* These ratings are stocked.
** Part Numbers listed are for a capacitance tolerance of ± 10 %. To specifiy ± 20 % tolerance, change the “X9” in the Part Number to “X0”;
for ± 5 %, from “X9” to “X5”.
*** The peak current pulse capability ot these capacitors is 10 amperes/µF. The maximum rate voltage change is 10 V/µS.
www.vishay.com
26
For technical questions, contact: spresale@vishay.com
Document Number: 42029
Revision: 07-Feb-07
Not for New Design
Type 730P
Film Capacitors
High Frequency, Wrap-and-Fill,
Metallized Polypropylene
STANDARD RATINGS
in inches [millimeters]
CAPACITANCE
(µF)
0.047
0.056
0.068
0.082
0.1*
0.12
0.15*
0.18
0.22
0.27
0.33
0.39
0.47*
0.56
0.68
0.82
1.0*
1.2
1.5
1.8
2.0*
2.2
2.7
3.0*
3.3
3.9
PART
NUMBER**
730P473X9400
730P563X9400
730P683X9400
730P823X9400
730P104X9400
730P124X9400
730P154X9400
730P184X9400
730P224X9400
730P274X9400
730P334X9400
730P394X9400
730P474X9400
730P564X9400
730P684X9400
730P824X9400
730P105X9400
730P125X9400
730P155X9400
730P185X9400
730P205X9400
730P225X9400
730P275X9400
730P305X9400
730P335X9400
730P395X9400
CASE SIZE
D
L
0.258 [6.6]
0.275 [7.0]
0.297 [7.5]
0.320 [8.1]
0.348 [8.8]
0.299 [7.6]
0.328 [8.3]
0.353 [9.0]
0.385 [9.8]
0.421 [10.7]
0.469 [11.9]
0.503 [12.8]
0.545 [13.8]
0.506 [12.9]
0.551 [14.0]
0.599 [15.2]
0.655 [16.6]
0.712 [18.1]
0.658 [16.7]
0.716 [18.2]
0.752 [19.1]
0.786 [20.0]
0.865 [22.0]
0.909 [23.1]
0.951 [24.2]
1.031 [26.2]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
0.75 [19.0]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.00 [25.4]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.25 [31.8]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
1.75 [44.5]
MAXIMUM RIPPLE CURRENT
ESR
(Amps rms) at 20 kHz
(Milliohms)
Case Temperature*** at
20 kHz -
100 Khz
+ 25 °C + 35 °C + 45 °C + 55 °C + 65 °C + 75 °C + 85 °C
400 WVDC
-
-
-
-
-
Not applicable. These capacitance values are not customarily
-
used in switched-mode power supplies.
-
-
-
-
-
-
-
-
-
-
-
-
-
32.0
5.7
5.5
5.0
4.4
3.8
3.2
2.2
31.0
5.7
5.7
5.3
4.4
4.1
3.3
2.3
30.0
5.7
5.7
5.5
4.8
4.3
3.5
2.4
28.0
5.7
5.7
5.6
5.3
4.5
3.7
2.6
27.0
5.7
5.7
5.7
5.7
5.7
4.7
4.3
26.0
6.3
6.2
6.0
5.9
5.8
4.9
4.5
25.0
7.0
6.9
6.7
6.6
6.5
5.2
4.7
23.0
8.0
7.9
7.8
7.7
6.8
5.5
5.0
21.0
9.0
9.0
9.0
8.0
7.0
5.7
5.2
20.0
9.0
9.0
9.0
8.3
7.4
5.9
5.4
19.0
9.0
9.0
9.0
8.6
7.6
6.0
5.6
17.0
9.0
9.0
9.0
9.0
7.9
6.4
5.9
16.0
9.0
9.0
9.0
9.0
8.1
6.6
6.3
15.0
9.0
9.0
9.0
9.0
8.3
6.8
6.5
630 WVDC
-
-
-
-
-
-
-
Not applicable. These capacitance values are not customarily
-
used in switched-mode power supplies.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
28.0
6.8
6.3
5.8
5.2
4.5
3.6
2.6
26.0
7.4
6.9
6.3
5.6
4.8
4.0
2.8
25.0
7.8
7.2
6.6
5.9
5.1
4.2
2.9
22.0
8.1
7.5
6.9
6.2
5.3
4.3
3.1
18.0
8.6
7.9
7.3
6.5
5.6
4.6
3.6
Vishay Sprague
0.022*
730P223X9630
0.283 [7.2] 0.75 [19.0]
0.027
730P273X9630
0.307 [7.8] 0.75 [19.0]
0.033
730P333X9630
0.334 [8.5] 0.75 [19.0]
0.039
730P393X9630
0.358 [9.1] 0.75 [19.0]
0.047
730P473X9630
0.388 [9.9] 0.75 [19.0]
0.056
730P563X9630 0.418 [10.6] 0.75 [19.0]
0.068
730P683X9630
0.346 [8.8] 1.00 [25.4]
0.082
730P823X9630
0.374 [9.5] 1.00 [25.4]
0.1
730P104X9630 0.408 [10.4] 1.00 [25.4]
0.12
730P124X9630 0.443 [11.3] 1.00 [25.4]
0.15
730P154X9630 0.496 [12.6] 1.00 [25.4]
0.18
730P184X9630 0.538 [13.7] 1.00 [25.4]
0.22
730P224X9630 0.496 [12.6] 1.25 [31.8]
0.27
730P274X9630 0.542 [13.8] 1.25 [31.8]
0.33
730P334X9630 0.593 [15.1] 1.25 [31.8]
0.39
730P394X9630 0.639 [16.2] 1.25 [31.8]
0.47
730P474X9630 0.696 [17.7] 1.25 [31.8]
0.56
730P564X9630 0.608 [15.4] 1.75 [44.5]
0.68
730P684X9630 0.664 [16.9] 1.75 [44.5]
0.82
730P824X9630 0.724 [18.4] 1.75 [44.5]
1.0*
730P105X9630 0.794 [20.2] 1.75 [44.5]
* These ratings are stocked.
** Part Numbers listed are for a capacitance tolerance of ± 10 %. To specifiy ± 20 % tolerance, change the “X9” in the Part Number to “X0”;
for ± 5 %, from “X9” to “X5”.
*** The peak current pulse capability ot these capacitors is 10 amperes/µF. The maximum rate voltage change is 10 V/µS.
ORDERING INFORMATION
730P
TYPE
224
CAPACITANCE
X9
CAPACITANCE TOLERANCE
100
DC VOLTAGE RATING*
This is expressed in volts.
X0 = ± 20 %
This is expressed in picofarads. The first two
X9 = ± 10 %
digits are the significant figures. The third is
X5 = ± 5 %
the number of zeros to follow.
* At + 85 °C, AC rms ratings for frequencies up to and including 400 Hz correspond to this table:
WVDC
100
250
400
630
RATED rms VOLTS
70
175
275
275
Document Number: 42029
Revision: 07-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
27
Legal Disclaimer Notice
Vishay
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000
Revision: 08-Apr-05
www.vishay.com
1
模拟电子
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
