Series 1-Channel (Form A)
High Capacity 4-Pin Type
FEATURES
4.3
.169
4.4
.173
2.1
.083
RELAYS
TYPICAL APPLICA
mm
inch
1. Greatly increased load current in the
same, miniature, 4-pin SO package.
2. Greatly improved specs allow you to
use this in place of mercury and
mechanical relays.
• Measuring instrument marke
• Security market
(use in I/O for alarm and secur
etc.)
1
4
2
3
TYPES
Output rating*
Type
AC/DC type
Load voltage
60 V
Load current
1.0 A
Part No.
Picked from the 1/2-pin side
Picked from the 3/4-pin side
1 Form A
1 Form A
AQY212GSX
AQY212GSZ
Packing qu
Tape and reel: 1
* Indicate the peak AC and DC values.
Notes: (1) Tape package is the standard packing style. Also available in tube. (Part No. suffix "X" or "Z" is not needed when ordering; Tub
Case: 2,000 pcs.)
(2) For space reasons, the initial letters of the product number “AQY” and “S” are ommited on the product seal.
The package type indicator “X” and “Z” are omitted from the seal. (Ex. the label for product number AQY212GS is 212G).
RATING
1. Absolute maximum ratings (Ambient temperature: 25°C
77°F)
Item
LED forward current
LED reverse voltage
Peak forward current
Symbol
I
F
V
R
I
FP
P
in
V
L
I
L
I
peak
P
out
P
T
V
iso
T
opr
T
stg
AQY212GS
50 mA
5V
1A
75 mW
60 V
1.0 A
3.0 A
300 mW
350 mW
1,500 V AC
–40°C to +85°C
–40°F to +185°F
–40°C to +100°C
–40°F to +212°F
100ms (1 shot), V
L
= DC
Remarks
Input
f = 100 Hz, Duty factor = 0.1
Power dissipation
Load voltage (peak AC)
Continuous load current
(peak AC)
Output
Peak load current
Power dissipation
Total power dissipation
I/O isolation voltage
Temperature limits
Operating
Storage
Non-condensing at low temp
1
LED operate current, mA
5
LED turn off current, mA
–40
–20
5
Turn off time, ms
0.8
4
4
0.6
3
3
0.4
2
2
0.2
1
1
0
–40 –20
0
20
40
60
80 85
0
0
20
40
60
8085
0
–40 –20
0
20
40
Ambient temperature,
°C
Ambient temperature,
°C
Ambient temperatu
7. LED dropout voltage vs. ambient
temperature characteristics
LED current: 5 to 50 mA
1.5
8. Voltage vs. current characteristics of output
at MOS portion
Measured portion: between terminals 3 and 4;
Ambient temperature: 25°C
77°F
Current, mA
3
2
1
9. Off state leakage current
Measured portion: between terminals 3
Ambient temperature: 25°C
77°F
1.4
Off state leakage current, A
LED dropout voltage, V
10
-4
10
-6
1.3
50mA
1.2
30mA
20mA
10mA
5mA
1
–40 –20
0
20
40
60
80 85
–2
–3
–1
–0.5
0.5
Voltage, V
–1
1
10
-8
1.1
10
-10
10
-12
0
10
20
30
40
Ambient temperature,
°C
Load voltage, V
10. LED forward current vs. turn on time
characteristics
Measured portion: between terminals 3 and 4;
Load voltage: 10 V (DC);
Continuous load current: 100 mA (DC);
Ambient temperature: 25°C
77°F
5
11. LED forward current vs. turn off time
characteristics
Measured portion: between terminals 3 and 4;
Load voltage: 10 V (DC);
Continuous load current: 100 mA (DC);
Ambient temperature: 25°C
77°F
0.5
12. Applied voltage vs. output cap
characteristics
Measured portion: between terminals 3
Frequency: 1 MHz;
Ambient temperature: 25°C
77°F
800
Output capacitance, pF
700
600
500
400
300
200
100
Turn on time, ms
3
Turn off time, ms
4
0.4
0.3
2
0.2
1
0.1
0
0
0
10
20
30
40
50
0
10
20
30
40
50
LED forward current, mA
LED forward current, mA
0
0
10
20
30
40
Applied voltage,
SAFETY WARNINGS
• Do not use the product under conditions
that exceed the range of its specifications.
It may cause overheating, smoke, or fire.
• Do not touch the recharging unit while
the power is on. There is a danger of
electrical shock. Be sure to turn off the
power when performing mounting,
maintenance, or repair operations on the
relay (including connecting parts such as
the terminal board and socket).
• Check the connection diagra
catalog and be sure to connec
terminals correctly. Erroneous
connections could lead to une
operating errors, overheating,
NOTES
1. Short across terminals
Do not short circuit between terminals
when relay is energized. There is
possibility of breaking the internal IC.
2. Surge voltages at the input
If reverse surge voltages are present at
the input terminals, connect a diode in
reverse parallel across the input terminals
and keep the reverse voltages below the
reverse breakdown voltage.
1
2
4
3
2) Keep the LED operate current at 50
mA or less at E
max
.
E
min.
E
max.
5. Output spike voltages
1) If an inductive load generates spike
voltages which exceed the absolute
maximum rating, the spike voltage must
be limited.
Typical circuits are shown below.
1
4
2) If spike voltages generated
are limited with a clamp diode
circuit wires are long, spike vo
occur by inductance. Keep wir
as possible to minimize induct
6. Cleaning solvents compa
Dip cleaning with an organic s
recommended for removal of s
dust, etc. Select a cleaning so
the following table. If ultrasonic
used, the severity of factors su
frequency, output power and c
solvent selected may cause lo
and other defects. Make sure
conditions are correct before u
details, please consult us.
Cleaning solvent
Chlorine- • Trichlene
base
• Chloroethlene
• Indusco
Adueous • Hollis
• Lonco Terg
Alcohol- • IPA
base
• Ethanol
• Thinner
Others
• Gasoline
3. Recommended LED forward current
(I
F
)
It is recommended that the LED forward
current (I
F
) be kept at 5mA.
4. Ripple in the input power supply
If ripple is present in the input power
supply, observe the following:
1) For LED operate current at E
min
,
maintain the value mentioned in the table
of “Note 3. Recommended LED forward
current (I
F
).”
2
3
Load
Co
(r
1
4
Add a clamp diode
to the load
2
3
Load
Add a CR snubber
circuit to the load
7. Soldering
When soldering this terminals, the following conditions are recommended.
(1) IR (Infrared reflow) soldering method
(2) Vapor phase soldering method
T
3
T
2
T
1
T
2
T
1
(3) Double wave soldering me
T
2
T
1
t
1
t
2
t
1
t
2
t
1
t
2
T
1
= 155 to 165°C
311 to 329°F
T
2
= 180°C 200°C
356 to 392°F
T
3
= 245°C
473°F
or less
t
1
= 120 s or less
t
2
= 30 s or less
T
1
= 180 to 200°C
366 to 392°F
T
2
= 215°C
419°F
or less
t
1
= 40 s
t
2
= 40 s or less
T
1
= 155 to 165°C
311 to 329°F
T
2
= 260°C
500°F
or less
t
1
= 60 s or less
t
2+
t
3
= 5 s or less
(4) Soldering iron method
Tip temperature: 280 to 300°C
536 to
572°F
Wattage: 30 to 60 W
Soldering time: within 5 s
(5) Others
Check mounting conditions before using
other soldering methods (hot-air, hot
plate, pulse heater, etc.)
• The temperature profile indicates the
temperature of the soldered terminal on
the surface of the PC board. The ambient
temperature may increase exc
Check the temperature under
conditions.
• The conditions for the infrare
soldering apply when preheat
the VPS method.
下载中心专版
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
