FRAF1601G-FRAF1607G
Isolated 16.0AMP. Glass Passivated Fast Recovery Rectifiers
ITO-220AC
.185(4.7)
.173(4.4)
.406(10.3)
.390(9.90)
.134(3.4)DIA
.113(3.0)DIA
.272(6.9)
.248(6.3)
Features
Glass passivated chip junction.
High efficiency, Low VF
High current capability
High reliability
High surge current capability
Low power loss
.124(3.16)
.118(3.00)
.112(2.85)
.100(2.55)
.606(15.5)
.583(14.8)
.063(1.6)
MAX
.161(4.1)
.146(3.7)
Mechanical Data
Cases: ITO-220AC molded plastic
Epoxy: UL 94V-0 rate flame retardant
Polarity: As marked
High temperature soldering guaranteed:
260
o
C /10 seconds 0.25”,(6.35mm) from
case.
Mounting position: Any
Weight: 2.24 grams
Mounting torque: 5 in – 1bs. max.
.110(2.8)
.098(2.5)
.030(0.76)
.020(0.50)
.055(1.4)
.043(1.1)
.035(0.9)
.020(0.5)
.071(1.8)
MAX
.543(13.8)
.512(13.2)
2
.100(2.55)
.100(2.55)
PIN 1
PIN 2
CASE
Case Positive
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
o
Rating at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load
(JEDEC method )
Maximum Instantaneous Forward Voltage
@ 16.0A
Maximum DC Reverse Current @ T
C
=25
o
C
at Rated DC Blocking Voltage @ T
C
=125
o
C
Maximum Reverse Recovery Time ( Note 1)
Typical Junction Capacitance (Note 3)
Typical Thermal Resistance RθJC (Note 2)
Symbol
FRAF FRAF FRAF FRAF FRAF FRAF FRAF
Units
1601G 1602G 1603G 1604G 1605G 1606G 1607G
V
RRM
V
RMS
V
DC
I
(AV)
I
FSM
V
F
I
R
Trr
50
35
50
100
70
100
200
140
200
400
280
400
16.0
250
1.3
5.0
100
600
420
600
800
560
800
1000
700
1000
V
V
V
A
A
V
uA
uA
nS
pF
o
C/W
o
C
150
250
70
4.5
-65 to +150
500
Cj
R
θJC
Operating and Storage Temperature Range
T
J,
T
STG
1. Reverse Recovery Test Conditions: I
F
=0.5A, I
R
=1.0A, I
RR
=0.25A.
Notes:
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink Size
2” x 3” x 0.25” Al-Plate.
3. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C.
http://www.luguang.cn
mail:lge@luguang.cn
FRAF1601G-FRAF1607G
Isolated 16.0AMP. Glass Passivated Fast Recovery Rectifiers
RATINGS AND CHARACTERISTIC CURVES (FRAF1601G THRU FRAF1607G)
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
1000
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
20
AVERAGE FORWARD CURRENT. (A)
16
12
INSTANTANEOUS REVERSE CURRENT. ( A)
100
8
Tj=125
0
C
4
10
0
0
50
100
o
150
CASE TEMPERATURE. ( C)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
300
1
Tj=25
0
C
PEAK FORWARD SURGE CURRENT. (A)
250
TJ=125
0
C
8.3ms Single Half Sine Wave
JEDEC Method
0.1
0
20
40
60
80
100
120
140
200
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
150
100
80
50
40
0
NUMBER OF CYCLES AT 60Hz
FIG.5- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
INSTANTANEOUS FORWARD CURRENT. (A)
1
2
5
10
20
50
100
20
10
FIG.4- TYPICAL JUNCTION CAPACITANCE
150
125
4
2
1
CAPACITANCE.(pF)
100
75
50
Tj=25
0
C
f=1.0MHz
Vsig=50mVp-p
0.5
1
5
10
50
100
500 1000
0.4
0.2
25
Tj=25
o
C
Pulse Width=300 s
1% Duty Cycle
0.9
1.0
1.1
1.2
1.3
1.4
1.5
0
0.1
0.1
0.8
REVERSE VOLTAGE. (V)
INSTANTANEOUS FORWARD VOLTAGE. (V)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
(+)
0
-0.25A
trr
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
http://www.luguang.cn
mail:lge@luguang.cn
单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
