The MINMAX MA01 series is a new range of isolated 1W DC/DC converter modules in a small SIP-package. There are 24 models available with 5V, 12V or
24VDC input and single-or dual-output voltages. These products provide have a typical load regulation of 2.5% to 5.0% depending on model.
The MA01 DC/DC converters are a compromise between a more expensive fully regulated converter and a non-regulated converter. They offer the
designer a new solution for many cost critical applications where the output voltage variation has to be kept in a certain limit under all load conditions.
Model Selection Guide
Model
Number
Input
Voltage
(Range)
VDC
Output
Voltage
VDC
5
9
12
15
±5
±9
±12
±15
5
9
12
15
±5
±9
±12
±15
5
9
12
15
±5
±9
±12
±15
Output Current
Max.
Min.
Input Current
@Max. Load
mA(typ.)
238
228
232
230
237
234
233
236
99
95
95
95
99
98
95
94
50
48
48
48
50
49
48
49
@No Load
mA(typ.)
Load
Regulation
% (max.)
6.5
5
5.2
5
5.2
4.2
4.6
4.5
5
3.4
3.4
2.7
3.9
2.8
2.9
2.6
3.7
2.5
2.4
2.3
3.7
2.5
2.4
2.3
Reflected
Ripple
mA(typ.)
Max. capacitive
Load
µF
220
MA01-05S05
MA01-05S09
MA01-05S12
MA01-05S15
MA01-05D05
MA01-05D09
MA01-05D12
MA01-05D15
MA01-12S05
MA01-12S09
MA01-12S12
MA01-12S15
MA01-12D05
MA01-12D09
MA01-12D12
MA01-12D15
MA04-24S05
MA01-24S09
MA01-24S12
MA01-24S15
MA01-24D05
MA01-24D09
MA01-24D12
MA01-24D15
5
(4.5 ~ 5.5)
12
(10.8 ~ 13.2)
24
(21.6 ~ 26.4)
mA
200
110
84
67
±100
±56
±42
±34
200
110
84
67
±100
±56
±42
±34
200
110
84
67
±100
±56
±42
±34
mA
4
2
1.5
1
±2
±1
±0.8
±0.7
4
2
1.5
1
±2
±1
±0.8
±0.7
4
2
1.5
1
±2
±1
±0.8
±0.7
@Max. Load
%
84
87
87
87.5
84.5
86
86.5
86.5
84
86.5
88.5
88
84.5
86
88.5
87.5
84
86.5
87.5
87.5
83.5
86
87
87
Efficiency
(typ.)
30
7
100#
220
4
100#
12
220
8
100#
# For each output
Typ.
Max.
---
9
---
18
---
30
5
5.5
12
13.2
24
26.4
---
0.3
Internal Capacitor
---
450
11
Input Specifications
Parameter
Input Surge Voltage (1 sec. max.)
Input Voltage Range
Reverse Polarity Input Current
Internal Filter Type
Internal Power Dissipation
E-mail:sales@minmax.com.tw
Model
5V Input Models
12V Input Models
24V Input Models
5V Input Models
12V Input Models
24V Input Models
All Models
Min.
-0.7
-0.7
-0.7
4.5
10.8
21.6
---
---
Unit
VDC
A
mW
Tel:886-6-2923150
2013/01/21 REV:5
Page 1 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01 SERIES
Output Specifications
Output Voltage Balance
Line Regulation
Load Regulation
Parameter
Dual Output, Balanced Loads
For Vin Change of 1%
Io=20% to 100%
Conditions
Min.
---
---
Ripple & Noise (20MHz)
Temperature Coefficient
Short Circuit Protection
---
See Model Selection Guide
±0.01
30
±0.02
60
±1.05
±0.1
Typ.
Max.
±1.0
±1.2
Unit
%
%
---
mV
P-P
%/℃
0.5 Second Max.
General Specifications
I/O Isolation Voltage (rated)
I/O Isolation Resistance
Switching Frequency
MTBF (calculated)
Safety Approvals
I/O Isolation Capacitance
Parameter
60 Seconds
100KHz, 1V
MIL-HDBK-217F@25℃, Ground Benign
500 VDC
Conditions
1000
40
Min.
Typ.
---
---
Max.
---
---
1000
50
VDC
M
pF
Unit
CSA 60950-1 recognition,IEC/EN 60950-1(CB-scheme)
2,000,000
100
---
60
120
---
120
Hours
KHz
Input Fuse
500mA Slow-Blow Type
5V Input Models
200mA Slow-Blow Type
12V Input Models
100mA Slow-Blow Type
24V Input Models
Environmental Specifications
Case Temperature
Operating Ambient Temperature Range (See Power Derating Curve)
Storage Temperature Range
Humidity (non condensing)
Cooling
Parameter
Natural Convection
Conditions
Min.
-40
---
---
Max.
+85
+95
95
Unit
℃
℃
% rel. H
℃
℃
-50
Free-Air convection
---
+125
Lead Temperature (1.5mm from case for 10Sec.)
260
Power Derating Curve
Output Voltage Tolerance
+20%
+15%
+20%
+15%
Output Power (%)
Output Voltage(%)
+10%
Max.
+10%
+5%
Typ.
+5%
Vnom
Min.
Vnom
-5%
-5%
-10%
0%
20%
40%
60%
80%
-10%
100%
Output Load Current (%)
Notes
1
2
3
4
5
6
7
Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted.
Ripple & Noise measurement bandwidth is 0-20MHz.
These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these
modules; however they may not meet all specifications listed.
All DC/DC converters should be externally fused at the front end for protection.
Other input and output voltage may be available, please contact factory.
That “natural convection” is about 20LFM but is not equal to still air (0 LFM).
Specifications are subject to change without notice.
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/21 REV:5
Page 2 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01 SERIES
Package Specifications
Mechanical Dimensions
19.5 [0.77]
Pin Connections
Pin
1
2
0.5 [0.02]
10.2 [0.40]
Single Output
+Vin
-Vin
Dual Output
+Vin
-Vin
4
5
6
[0.13]
No Pin
+Vout
-Vout
Common
+Vout
-Vout
0.5
[0.02]
2.4
[0.09]
2.54
[0.10]
5.08
[0.20]
2X2.54
[2X0.10]
3.2
T=6.1[0.24] for 5V & 12V Input Models
T=7.1[0.28] for 24V Input Models
18.5 [0.73]
Bottom View
1
2
4
5
6
►All
dimensions in mm (inches)
T
►Tolerance:
X.X±0.25 (X.XX±0.01)
0.25 [0.01]
1.3 [0.05]
0.50
[0.02]
►
Pins ±0.05(±0.002)
X.XX±0.13 ( X.XXX±0.005)
Physical Characteristics
Case Size (5&12V Input)
Case Size (24V Input)
Case Material
Pin Material
Weight (5&12V Input)
Weight (24V Input)
:
:
:
:
:
:
19.5x6.1x10.2mm (0.77x0.24x0.40 inches)
19.5x7.1x10.2mm (0.77x0.28x0.40 inches)
Non-Conductive Black Plastic (flammability to UL 94V-0 rated)
Alloy 42
2.2g
2.6g
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/21 REV:5
Page 3 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01 SERIES
Test Setup
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with a inductor Lin (10µH) and Cin (1µF, ESR < 1.0 at 100 KHz) to simulate source impedance. Capacitor Cin, offsets
possible battery impedance.
Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz.
To Oscilloscope
+
Battery
+
Lin
+Vin
Current
Probe
+Out
Load
DC / DC
Converter
-Vin
-Out
Cin
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33µF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load
between 50 mm and 75 mm from the DC/DC Converter.
+Vin
Single Output
DC / DC
Converter
-Vin
-Out
+Out
Copper Strip
Cout
Copper Strip
Resistive
Scope
Load
+Vin
Dual Output
DC / DC
Converter
-Vin
+Out
Com.
-Out
Copper Strip
Cout
Copper Strip
Cout
Copper Strip
Scope
Scope
Resistive
Load
Maximum Capacitive Load
The MA01 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up,
affecting the ramp-up and the startup time. For optimum performance we recommend 100µF maximum capacitive load for dual outputs and 220µF capacitive load
for single outputs. The maximum capacitance can be found in the data sheet.
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In
applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup.
Capacitor mounted close to the power module helps ensure stability of the unit, it is commended to use a good quality low Equivalent Series Resistance (ESR < 1.0
at 100 KHz) capacitor of a 2.2µF for the 5V input devices, a 1.0µF for the 12V input devices and a 0.47µF for the 24V devices.
+
DC Power
Source
-
+
Cin
-Vin
-Out
+Vin
DC / DC
Converter
+Out
Load
Technical Notes
Output Ripple Reduction
A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is
recommended to use 1.0µF capacitors at the output.
+
DC Power
Source
-
-Vin
+Vin
Single Output
DC / DC
Converter
-Out
+Out
+
DC Power
Source
-
+Vin
+Out
Dual Output
DC / DC Com.
Converter
Cout
Cout
Load
Load
Cout
Load
-Vin
-Out
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the
maximum temperature rating of the components inside the power module, the case temperature must be kept below 95℃. The derating curves are determined from
measurements obtained in a test setup.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
